Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With commit ceec08f50b, phy is connected to slave 0, but
changing the phy node was missed, fix it by populating the
phy node to proper cpsw slave node.
Fixes: ceec08f50b ("ARM: dts: dra72-evm: Add mode-gpios entry for mac node")
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
Add a node for evm_3v3_sd using onboard PCF GPIO expander which feeds
on to mmc vdd.
Update mapping for vmmc-supply and vmmc_aux-supply.
evm_3v3_sd supplies to SD card vdd, and ldo1 to sdcard i/o lines.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. This is controlled by pcf gpio line. Add
appropriate mode-gpios DT entry so that driver can select the required
slave.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
PCF8575 does not have any registers hence, offset field needs to be
ignored for i2c read/write. Therefore populate u-boot,i2c-offset-len
with 0 in PCF8575 DT nodes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
According to AM572x DM SPRS953A, QSPI max bus speed is 76.8MHz.
Therefore update the spi-max-frequency value of QSPI node for DRA74 and
DRA72 evm. This increase flash read speed by ~2MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better
throughput.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.
In DRA72x and AM57xx EVMs the card detect gpio is designed as
active low gpio. So correcting the dt card detect gpio
definition.
Also adding card-detect gpio for DRA74x EVM.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
- Import various DT files for DRA7 / DR72x / dra72-evm from Linux Kernel
v4.1
- Add config file for this board, enable DM and DM_GPIO
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Lokesh Vutla
Mugunthan V N
Vignesh R
Tom Rini