Commit graph

24 commits

Author SHA1 Message Date
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Tom Rini
219f4788d3 hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-06-20 20:36:51 +02:00
Marek Vasut
d5f6a15a39 CMD: Drop CONFIG_CMD_DFL, it's not used
$ git grep CMD_DFL
board/atc/ti113x.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
board/atc/ti113x.c:     pci_writew (s, PCI_COMMAND, CMD_DFLT);
board/cpc45/pd67290.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
board/cpc45/pd67290.c:  pci_writew (s, PCI_COMMAND, CMD_DFLT);
drivers/pcmcia/i82365.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
drivers/pcmcia/i82365.c:        pci_writew (s, PCI_COMMAND, CMD_DFLT);
include/configs/MBX.h:#define CONFIG_CMD_DFL
include/configs/MigoR.h:#define CONFIG_CMD_DFL
include/configs/digsy_mtc.h:#define CONFIG_CMD_DFL
include/configs/ms7722se.h:#define CONFIG_CMD_DFL
include/configs/ms7750se.h:#define CONFIG_CMD_DFL
include/configs/r2dplus.h:#define CONFIG_CMD_DFL
include/configs/sh7757lcr.h:#define CONFIG_CMD_DFL
include/configs/sh7785lcr.h:#define CONFIG_CMD_DFL

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pfister_Werner@intercontrol.de
Cc: iwamatsu@nigauri.org
Cc: nobuhiro.iwamatsu.yj@renesas.com
Cc: vapier@gentoo.org
Cc: wd@denx.de
Cc: yoshihiro.shimoda.uh@renesas.com
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-04-19 22:01:13 +02:00
Anatolij Gustschin
02ab0970b3 mpc5200: digsy_mtc: Fix extension board detection
Switch to extension board detection using pci_find_device()
instead of detecting by i2c access to EEPROM device on
extension board.

This is a cleaner detection method since EEPROM addresses
can be different on different board revisions. This also
avoids "i2c_read: failed to address chip" error messages
in the boot log on boards without extension board which
may confuse users.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-12-12 08:17:05 +01:00
Anatolij Gustschin
4fc823ddb4 mpc5200: digsy_mtc: fix detection of Coral-PA
A delay of approximately 250 ms after PCI bus reset in
pci_mpc5xxx_init() is needed to recognize the Coral-PA
controller on the graphic extention board.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-10-15 22:18:39 +02:00
Anatolij Gustschin
eccfb49046 mpc5200: digsy_mtc: fix extension board EEPROM I2C address for rev5
On newer rev5 hardware the extension board EEPROM I2C address
has been changed to 0x54. Make this I2C address configurable
depending on CONFIG_DIGSY_REV5 so that extention board presence
detection works correctly on newer hardware.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-08-04 23:32:33 +02:00
Anatolij Gustschin
348de314be digsy_mtc: move board into vendor dir and add vendor logo
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-07-27 23:27:07 +02:00
Anatolij Gustschin
a59996e3f7 mpc5200: digsy_mtc: add support for graphic extension board
Add detection and initialisation for graphic extension board
and support splash screen when booting. Enable "bmp" command
in the board configuration and provide "disp" command to
be able to switch the display on/off.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-07-27 23:26:20 +02:00
Heiko Schocher
1b41493def mpc52xx, digsy_mtc: change phy addr for rev5 boards.
- rev5 board has phy addr 1 -> adapt CONFIG_PHY_ADDR define
  in board config file.
- also fixup the phy addr entry in dts, before booting
  Linux.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-28 00:52:09 +02:00
Heiko Schocher
a01ebd9679 mpc52xx, digsy_mtc: add trickle charger support for rev5 boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-26 00:25:05 +02:00
Heiko Schocher
927d2cea6b mpc52xx, digsy_mtc_rev5: Fix Linux crash, if no Flash in bank 2
If no Flash is connected to cs1, Linux crashes, because
reg entries are not correct adapted.

Following fix is needed:
- swap base addresses in CONFIG_SYS_FLASH_BANKS_LIST, as
  flash bank 1 is on chipselect 0 and flash bank 2 on
  chipselect 1
- call fdt_fixup_nor_flash_size() from ft_board_setup()

Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
2011-03-21 22:51:27 +01:00
Heiko Schocher
466f0137e8 mpc5200, digsy_mtc: add support for rev5 board version
difference to previous board version:
- M29W128GH flash from Numonyx
- SDRAM ISSI IS45S16800 (Option A2 105°C)
- rev5 uses RTC RV-3029-C2
- update cs0 and cs1 baseaddr and length
  depending on the detected flash size.
- added Werner Pfister <Pfister_Werner@intercontrol.de>
  as maintainer for the digsy board variants
- As the M29W128GH needs a special flash_cmd_reset()
  document that in the new file doc/README.cfi.
- move "#endif /* CONFIG_CMD_IDE */" to the right place
- remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5
  boards
- change doc/README.cfi as Stefan Roese suggested

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
2011-01-18 23:34:26 +01:00
Wolfgang Denk
25ddd1fb0a Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:05:30 +02:00
Wolfgang Denk
553f09823c Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE
CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE

No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.

Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken.  Last known maintainers on Cc:

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:03:25 +02:00
Peter Tyser
d98b0523cf powerpc: Cleanup BOOTFLAG_* references
Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.

Note that this change makes the board info bd_bootflags field useless.
It will always be set to 0, but we leave it around so that we don't
break the board info structure that some OSes are expecting to be passed
from U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-18 22:38:56 +02:00
Wolfgang Denk
2ae1824196 Makefile: move all Power Architecture boards into boards.cfg
Clean up Makefile, and drop a lot of the config.mk files on the way.

We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:12:04 +02:00
Wolfgang Denk
14d0a02a16 Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:07:10 +02:00
Werner Pfister
c569ad6e1e digsy_mtc: Add TCR register value for RTC (DS1339)
Signed-off-by: Werner Pfister <werner.pfister@intercontrol.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-09-24 00:21:06 +02:00
Detlev Zundel
ff27650bb2 digsy_mtc: Update default environment
Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-08-09 23:01:41 +02:00
Grzegorz Bernacki
a781de1270 digsy mtc: Enable command line history.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2009-07-19 21:43:00 +02:00
Grzegorz Bernacki
1260233982 digsy mtc: Add description to GPIO initial configuration.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2009-06-14 23:06:03 +02:00
Grzegorz Bernacki
f1f66edfc7 digsy MTC: Add SPI support.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2009-06-14 23:03:57 +02:00
Wolfgang Denk
c0a14aedc3 Update CHANGELOG, coding style cleanup. 2009-04-05 00:27:57 +02:00
Grzegorz Bernacki
5c4fa9b474 Add support for the digsy MTC board.
This is the InterControl custom device based on the MPC5200B chip.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2009-03-20 22:39:14 +01:00