Without this function the USB compliance test (USB 2.0 Command Verifier) will
fail in the "Interface Descriptor Test" with this error message:
FAIL
(1.2.51) A successful GetInterface request must return the alternate setting
set by a prior call to SetInterface.
Lets add this function to read back the value so that the DFU device fully
passes the USB compliance test.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Enrico Leto <enrico.leto@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
On the DXR2 board (AM335x using MUSB) the USB compliance test suite
(USB 2.0 Command Verifier) will cause the board to crash and reset
upon the "BOS Descriptor Test - Addressed state". Here the output
from the DRX2 while running this test:
GADGET DRIVER: usb_dnl_dfu
musb-hdrc: peripheral reset irq lost!
composite_setup (776)
data abort
pc : [<87f693ac>] lr : [<87f6911c>]
sp : 86f33a58 ip : 00000000 fp : 86f3bbac
r10: 00000f00 r9 : 86f33ef4 r8 : 86f37da8
r7 : 00000005 r6 : 86f33a90 r5 : 00000000 r4 : 86f37e30
r3 : 00000000 r2 : 00000000 r1 : 87f9c888 r0 : 00000016
Flags: Nzcv IRQs off FIQs on Mode SVC_32
Resetting CPU ...
resetting ...
By adding the case statement for USB_DT_BOS and therefore not running
into the default case (jump to unkown label) this crash is fixed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Enrico Leto <enrico.leto@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This does nothing now, so drop it. We have SPL anyway to do our low-level
init.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The current sunxi implementation uses gdata, which is going away. It also
sets up DRAM before board_init_f() in SPL.
There is really no reason to do much in s_init() since board_init_f() is
called immediately afterwards. The only change is that we need our own
implementation of board_init_f() which sets up DRAM before the BSS (which
is in DRAM) is cleared.
The s_init() code runs once for SPL and again for U-Boot proper. We
shouldn't need to init the clock/timer/gpio/i2c init twice, so just have it
in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to get rid of this SPL-specific setting of the global_data pointer.
It is already set up in start.S immediately before board_init_f() is called,
and there may be information there that is needed (e.g. pre-reloc malloc
info).
Signed-off-by: Simon Glass <sjg@chromium.org>
Prior to this change we set the gd pointer early so that we can store
data in it. This becomes problematic for DM changes as well as being
odd in general. Re-work the code paths so that we don't need to set the
gd pointer so early and instead can rely upon the normal setting of it.
In order to do this we do need to move certain calls from s_init into
spl_board_init(), mainly preloader_console_init and
save_omap_boot_params.
Tested on: Beaglebone Black, AM43xx GP EVM, Beagleboard, Beagleboard xM,
OMAP5 uEVM, DRA7xx EVM
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Now TQM8xx is the only remaining board family of mpc8xx.
It uses its own linker script, board/tqc/tqm8xx/u-boot.lds.
arch/powerpc/cpu/mpc8xx/u-boot.lds is not used by any boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Since commit 843125daeb (ppc4xx: remove HH405 board), CONFIG_HH405
is not defined.
Since commit d526330479 (ppc4xx: remove PMC405), CONFIG_PMC405
is not defined.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
As a preparation to ARCv2 port submission we rename "arc700" folder to
"arcv1" which stands for ARCv1 ISA also known as ARCompact.
This will allow us to add more flavours of binary-compatible ARCv1 CPUs
like ARC600 if needed later on and all required ARCv2 CPUs (which are
binary incompatible with ARCv1) in "arcv2" folder in subsequent commits.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
Both ARCangel4 and AXS10x are FPGA-based boards so they may have
different CPUs. For now we have only 1 option (ARC700) and we define
this as default in arch Kconfig.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
"reset.c" and "cpu.c" have no architecture-specific code at all.
Others are applicable to either ARC CPU.
This change is a preparation to submission of ARCv2 architecture port.
Even though ARCv1 and ARCv2 ISAs are not binary compatible most of
built-in modules still have the same programming model - AUX registers
are mapped in the same addresses and hold the same data (new featues
extend existing ones).
So only low-level assembly code (start-up, interrupt handlers) is left
as CPU(actually ISA)-specific. This significantyl simplifies maintenance
of multiple CPUs/ISAs.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
* use better symbols for relocatable region boundaries
("__image_copy_start" instead of "CONFIG_SYS_TEXT_BASE")
* remove useless debug messages because they will only show up in case
of both problem (when normal "if" branch won't be taken) and DEBUG take
place which is pretty rare situation.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Even though existing implementation works fine in preparation to
submission of ARCv2 architecture we need this change.
In case of ARCv2 interrupt vector table consists of just addresses
of corresponding handlers. And if those addresses will be in .text
section then assembler will encode them as everything in .text section
as middle-endian and then on real execution CPU will read swapped
addresses and will jump into the wild.
Once introduced new section is situated so .text section remains the
first which allows us to use common linker option for linking everything
to a specified CONFIG_SYS_TEXT_BASE.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
Depending on MMU presence in CPU there're differences in HW behavior.
For example address of instruction that caused exception is put in
ECR register if MMU exists and in ERET register otherwise.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
To disable interrupts we need to reset corresponding flags in STATUS32
register. For this we need to OR flags for interrupts level1 and level2
and then AND with current value in STATUS32.
Before that implementation was incorrect.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
Exception cause register (ECR) contains value that describes a reason
for exception that has happened. This helps a lot to figure-out what
went wrong.
Now we print this register contents when dumping registers.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
Some cache operations ({i|d}cache_{enable|disable|status} or
flush_dcache_all) are built and used even if CONFIG_SYS_{I|D}CACHE_OFF
is set.
This is required for force disable of caches on early boot.
What if something was executed before U-boot and enabled caches
(low-level bootloaders, previously run kernel etc.)?
But if CPU doesn't really have caches any attempt to access
cache-related AUX registers triggers instruction error exception.
So for convenience we'll try to avoid exceptions by checking if CPU
actually has caches (we check separately data and instruction cache
existence) at all.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
Normally buildman runs with 'make -s' meaning that only errors and warnings
appear in the log file. Add a -V option to run make in verbose mode, and
with V=1, causing a full build log to be created.
Signed-off-by: Simon Glass <sjg@chromium.org>
The site at https://www.kernel.org/pub/tools/crosstool/ is a convenient
repository of toolchains which can be used for U-Boot. Add a feature to
download and install a toolchain for a selected architecture automatically.
It isn't clear how long this site will stay in the current place and
format, but we should be able to rely on bug reports if it changes.
Suggested-by: Marek Vašut <marex@denx.de>
Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
We should create a test setting file when running testes, not use whatever
happens to be on the local machine.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since we need a few modules which might not be available in a bare-bones
distribution, add a note about that to the README.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Wolfgang Denk <wd@denx.de>
In some cases there may be multiple toolchains with the same name in the
path. Provide an option to use the full path in the CROSS_COMPILE
environment variable.
Note: Wolfgang mentioned that this is dangerous since in some cases there
may be other tools on the path that are needed. So this is set up as an
option, not the default. I will need test confirmation (i.e. that this
commit fixes a real problem) before merging it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Steve Rae <srae@broadcom.com>
If:
1. Toolchains A and B have the same filename
2. Toolchain A is in the PATH
3. Toolchain B is given in ~/.buildman and buildman uses it to build
then buildman will add toolchain B to the end of its path but will not
necessarily use it since U-Boot will find toolchain A first in the PATH.
Try to fix this by putting the toolchain first in the path instead of
last.
Signed-off-by: Simon Glass <sjg@chromium.org>
The assumption that the compiler name will always end in gcc is incorrect
for clang and apparently on BSD.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the -b flag to permit a range expression as well as a branch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When running tests the output directory is often wiped. This is only safe if
a branch is being built. The output directory may contain other things
besides the buildman test output.
Signed-off-by: Simon Glass <sjg@chromium.org>
When building current source for a single board, buildman puts the output
in <output_dir>/current/current/<board>. Add an option to make it use
<output_dir>/<board> instead. This removes the unnecessary directories
in that case, controlled by the --no-subdirs/-N option.
Suggested-by: Tom Rini <trini@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Buildman normally obtains the upstream commit by asking git. Provided that
the branch was created with 'git checkout -b <branch> <some_upstream>' then
this normally works.
When there is no upstream, we can try to guess one, by looking up through
the commits until we find a branch. Add a function to try this and print
a warning if buildman ends up relying on it.
Also update the documentation to match.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Wolfgang Denk <wd@denx.de>
This is not needed since we always do a full (non-incremental) build. Also
it might be dangerous since it will try to delete everything below the
base directory.
Fix this potentially nasty bug.
Signed-off-by: Simon Glass <sjg@chromium.org>
Buildman currently puts current-source builds in a current/current
subdirectory, but there is no need for the extra depth.
Suggested-by: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Simon Glass <sjg@chromium.org>
It makes sense to specify CONFIG_SYS_CLK_FREQ in "configs/xx_defconfig"
instead of "include/configs/xxx.h" because then header will be reusable
across boards with different CPU clocks.
Also this nice to have an ability for end user to tune this value
himself via "menuconfig".
For now I'm only applying this change to all ARC configs because
otherwise scope of change will be huge.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Hans de Goede <hdegoede@redhat.com>
cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
If CONFIG_SPL_NOR_SUPPORT is defined, spl_nor_load_image() requires
spl_start_uboot(), CONFIG_SYS_OS_BASE, CONFIG_SYS_SPL_ARGS_ADDR,
CONFIG_SYS_FDT_BASE to be defined even if users just want to run
U-Boot, not Linux. This is inconvenient.
This patch is following the codying style of common/spl/spl_nand.c.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Allow booting the OpenRTOS payloads via fitImage image type.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add separate image type for the Wittenstein OpenRTOS .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some MTD defines are repeated twice; once with UBI and then with MTD.
Remove the duplicate MTD defines from the UBI grouping.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Stefan Roese
Simon Glass
Tom Rini
Masahiro Yamada
Alexey Brodkin
Igor Guryanov
Michal Simek
Alexey Brodkin
Marek Vasut
Evgeni Dobrev
Bill Pringlemeir