Commit graph

27 commits

Author SHA1 Message Date
pekon gupta
e53ad4b445 board/ti/am43xx: add support for parallel NAND
This patch adds support for NAND device connected to GPMC chip-select on
following AM43xx EVM boards.

am437x-gp-evm: On this board, NAND Flash signals are muxed with eMMC, thus at a
  time either eMMC or NAND can be enabled. Selection between eMMC and NAND is
  controlled by:
  (a) Statically using Jumper on connecter (J89) present on board.
  (a) If Jumper on J89 is NOT used, then selection can be dynamically controlled
      by driving SPI2_CS0[MUX_MODE=GPIO] pin via software:
      SPI2_CS0 == 0: NAND (default)
      SPI2_CS0 == 1: eMMC

am43x-epos-evm: On this board, NAND Flash control lines are muxed with QSPI,
  Thus only one of the two can be used at a time. Selection is controlled by:
  (a) Dynamically driving following GPIO pin from software
      GPMC_A0(GPIO) == 0 NAND is selected (default)

NAND device (MT29F4G08AB) on these boards has:
 - data-width=8bits
 - blocksize=256KB
 - pagesize=4KB
 - oobsize=224 bytes
For above NAND device, ROM code expects the boot-loader to be flashed in BCH16
ECC scheme for NAND boot, So by default BCH16 ECC is enabled for AM43xx EVMs.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-08-25 10:48:12 -04:00
Tom Rini
7aa5598aac tps65218/am43xx_evm: Add power framework support to TPS65218
Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.

Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-07-25 15:21:06 -04:00
Felipe Balbi
9cb9f3331b board: ti: am43xx: add support for AM43xx Starter Kit
AM43xx Starter Kit is a new board based on
AM437x line of SoCs. Being a low-cost EVM and
small size EVM are intended to provide an entry
level development platform on a full fledged
Hardware System.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-06-19 17:53:58 -04:00
Tom Rini
83bad1026b arm:am43xx: Add TPS65218 support to scale voltages up
This family is supported by the TPS65218 PMIC.  Implement a scale_vcores
to set the MPU and CORE voltage correctly to the max frequency that is
supported (and what we will be scaling them to in setup_dplls()).

Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:16 -04:00
Lokesh Vutla
fa03834fdf ARM: AM43xx: Fix mmcboot command in EXTRA_ENV_SETTINGS
loadbootenv expects devtype variable to be set. This is missing in
mmcboot command. With this the following error comes:
U-Boot# run mmcboot
mmc0 is current device
SD/MMC found on device 0
** Bad device usb 0 **
** Bad device usb 0 **
Fixing this by setting devtype as mmc.

Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-06-06 17:46:15 -04:00
Tom Rini
196311dc72 arm:am33xx: Rework s_init and add board_early_init_f
With the changes to the i2c framework (and adopting the omap24xx_i2c
driver to them) we can no longer call i2c functions prior to gd having
been set and cleared.  When SPL booting, this is handled by setting gd
to point to SRAM in s_init.  However in the cases where we are loaded
directly by ROM (memory mapped NOR or QSPI) we need to make use of the
normal hooks to slightly delay these calls.

Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:14 -04:00
Sourav Poddar
7a5f71bc40 am43xx_evm: Add qspiboot target
The ePOS EVM and EVM SK have QSPI as an option to boot.  Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices.  As QSPI is booted from directly we need to chang
CONFIG_SYS_TEXT_BASE.

Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices
we need to handle that elsewhere, once NAND support is also added.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-06 17:46:12 -04:00
Tom Rini
2e8f5dc16a am43xx_evm: Drop SPI SPL
QSPI booting on this board does not use SPL, so drop SPI-SPL related
options.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:40:15 -04:00
Tom Rini
d3289aac64 TI:armv7: Change Falcon Mode DT load address
In general, we want to load the DT at base+128MB, so that we ahve
sufficient room for the kernel and a larger device tree.  In the case of
OMAP3, use 64MB instead as we have a number of boards with 128MB DDR.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:20:15 -04:00
Tom Rini
bea0fd5e6a am43xx_evm: Update the ramdisk args, we pass things in just fine via DT
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Tom Rini
fb3ad9bd92 TI: Add, use a DEFAULT_LINUX_BOOT_ENV environment string
To deal with a reoccurring problem properly we need to specify addresses
for the Linux kernel, Flatted Device Tree and ramdisk that obey the
constraints within the kernel's Documentation/arm/Booting file but also
make sure that we relocate things within a valid address range.

It is possible with these addresses to also set fdt_high and initrd_high
to the value of 0xffffffff.  We don't do this by default to allow for
the most likely success of people using custom addresses however.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Mugunthan V N
3a3939bf3d ARM: AM43xx: Add Ethernet boot support to SPL
Add Ethernet Boot support to SPL

Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:07 -05:00
Mugunthan V N
4cdd7fda91 ARM: AM43xx: Add CPSW support to AM43xx EPOS and GP EVM
Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected
to RMII and RGMII phy respectively and enable cpsw in config.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:06 -05:00
Tom Rini
eeb72e6761 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	arch/arm/cpu/armv7/config.mk
	board/ti/am43xx/mux.c
	include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 16:49:58 -05:00
Tom Rini
0f1b044395 am43xx_evm: Enable GPT commands
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 14:03:44 -05:00
Tom Rini
4c89a369c7 Merge branch 'master' of git://git.denx.de/u-boot-spi 2014-02-21 08:00:22 -05:00
Sourav Poddar
ea4c7a8321 am437x_epos_evm: add SPL API, QSPI, and serial flash support
Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-02-18 22:41:09 +05:30
Albert ARIBAUD
e97f9d817e Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-01-29 14:07:50 +01:00
Dan Murphy
2b36fe579c arm: am43xx: Add USB spl boot support
Add the USB host boot support for the am43xx evm
Add the macros to boot from a usb drive in uBoot

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2014-01-24 16:59:22 -05:00
Tom Rini
b1cde7e21f am43xx_evm.h: Correct SPL max size
Upon further inspection of relevant parts of the architecture, the
maximum SPL binary size is 220KiB.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-01-24 11:41:17 -05:00
Sekhar Nori
9f1a8cd33f ARM: AM43XX: board: add support for reading onboard EEPROM
Add support for reading onboard EEPROM to enable
board detection.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:00 -05:00
Lokesh Vutla
1564dba7d9 ARM: AM43xx: Add extra ENV settings
Add Extra env settings.
This is derived from am335x Extra ENV settings.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:00 -05:00
Lokesh Vutla
573b020ecb ARM: AM43xx: Add L2 Support
AM4372 uses PL310 L2 Cache. Enable the configs for the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:00 -05:00
Lokesh Vutla
369cbe1e1e ARM: AM43xx: Adapt to ti_armv7_common.h config file
Use ti_armv7_common.h config file to inclde the common
configs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-12-18 21:14:00 -05:00
Rob Herring
f232950f82 config: remove platform CONFIG_SYS_HZ definition part 2/2
Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:06:16 -05:00
Dan Murphy
3d799c7f5e usb: am437x: Add support for am437x xhci USB host
Add the support for the am437x xhci usb host.

The xHCI host on AM437 is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Lokesh Vutla
8d0afcd7c2 ARM: AM43xx: Add config file
Add config file

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00