Commit graph

9 commits

Author SHA1 Message Date
Tim Harvey
dad08286ea imx: ventana: add pci fixup for PLX PEX860x switch GPIO
Most Gateworks Ventana boards use a PLX PEX860x PCIe switch for PCIe expansion.
These boards use GPIO on the PLX device as PERST# for the downstream ports
thus we assert this when the PLX is enumerated.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-09-09 16:15:03 +02:00
Tim Harvey
9c0fe83eb5 imx: ventana: add econfig command
The Gateworks Ventana EEPROM contains a set of configuration bits that
affect the removal of device-tree nodes that support peripherals that do not
exist on sub-loaded boards. This patch adds:
 - a structure to define a config bit name, dt node alias, bit position
 - an array of supported configuration items
 - an econfig command to get/set/list configuration bits
 - use of the array when adjusting the FDT prior to boot

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-08-20 13:08:37 +02:00
Albert ARIBAUD
d6694aff56 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-06-30 23:00:34 +02:00
Tim Harvey
0cc11dea89 imx: ventana: switch to SPL
Switch to an SPL image. The SPL for Ventana does the following:
 - setup i2c and read the factory programmed EEPROM to obtain DRAM config
   and model for board-specific calibration data
 - configure DRAM per CPU/size/layout/devices/calibration
 - load u-boot.img from NAND and jump to it

This allows for a single SPL+u-boot.img to replace the previous multiple boa
configurations.

Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-06-06 10:07:26 +02:00
Stephen Warren
77b83e6d09 usb: hub: remove CONFIG_USB_HUB_MIN_POWER_ON_DELAY
Now that we wait the correct specification-mandated time at the end of
usb_hub_power_on(), I suspect that CONFIG_USB_HUB_MIN_POWER_ON_DELAY has
no purpose.

For cm_t35.h, we already wait longer than the original MIN_POWER_ON_DELAY,
so this change is safe.

For gw_ventana.h, we will wait as long as the original MIN_POWER_ON_DELAY
iff pgood_delay was at least 200ms. I'm not sure if this is the case or
not, hence I've CC'd relevant people to test this change.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2014-06-01 19:20:07 +02:00
Tim Harvey
7a278f9f1b imx: ventana: add HDMI and LVDS display capability
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-05-09 15:10:54 +02:00
Tim Harvey
effb7dc6d9 imx: ventana: Convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD on ventana.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-05-09 15:10:54 +02:00
Tim Harvey
234d89dac6 ventana: Add support for the LTC3676 PMIC
The LTC3676 PMIC is used instead of the PFUZE100 PMIC on the
GW51xx/GW52xx/GW53xx Ventana baseboards. In order to support the IMX6Q SoC
at 1GHz on those baseboards, we need to adjust the voltage scaling for the SW1
and SW3 DC/DC converters on the LTC3676 for 1225mV. Note that the scalar
values for the LTC3676 are board-specific as they relate to a resistor devider
chosen by the board design.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-05-09 15:10:43 +02:00
Tim Harvey
59189a8b26 ventana: Add Gateworks Ventana family support
Gateworks Ventana is a product family based on the i.MX6.  This
patch adds support for all boards in the Ventana family. Where
possible, data from the boards EEPROM is used to determine various
details about the board at runtime.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2014-03-12 10:23:03 +01:00