Commit graph

37 commits

Author SHA1 Message Date
Stefan Agner
5519194d4f mtd: vf610_nfc: add Freescale NFC controller configs to Kconfig
This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-05-24 14:27:28 -05:00
Peter Tyser
aff092ed13 nand: Remove unused CONFIG_MTD_NAND_ECC_JFFS2 option
This option was removed along with legacy NAND support in
be33b046b5.  Clean up some remnants.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2015-03-30 23:16:54 -05:00
Daniel Mack
c316f577b4 mtd: OMAP: Enable GPMC prefetch mode
Enable GPMC's prefetch feature for NAND access. This speeds up NAND read
access a lot by pre-fetching contents in the background and reading them
through the FIFO address.

The current implementation has two limitations:

 a) it only works in 8-bit mode
 b) it only supports read access

Both is easily fixable by someone who has hardware to implement it.

Note that U-Boot code uses non word-aligned buffers to read data into, and
request read lengths that are not multiples of 4, so both partial buffers
(head and tail) have to be addressed.

Tested on AM335x hardware.

Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: Daniel Mack <zonque@gmail.com>
[trini: Make apply again, use 'cs' fix pointed out by Guido]
Signed-off-by: Tom Rini <trini@ti.com>
2015-01-13 11:51:23 -05:00
Masahiro Yamada
4b0abf9f3c mtd: denali: add Denali controller configs to Kconfig
Commit 3eb3e72a3f (nand/denali: Adding Denali NAND driver support)
introduced some new options, and some of them were documented by
commit f9860cf081 (nand/denali: Document CONFIG symbols).

This commit allows users to enable/disable them via Kconfig
with more detailed help docs.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>
2014-10-05 14:10:09 +09:00
Scott Wood
f9860cf081 nand/denali: Document CONFIG symbols
The patch "nand/denali: Adding Denali NAND driver support"
introduced two config symbols without documenting them.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-25 13:54:58 -05:00
pekon gupta
434f2cfcad ARM: omap: move board specific NAND configs out from ti_armv7_common.h
This patch moves some board specific NAND configs:
- FROM: generic config file 'ti_armv7_common.h'
- TO:   individual board config files using these configs.
So that each board can independently set the value as per its design.

Following configs are affected in this patch:
  CONFIG_SYS_NAND_U_BOOT_OFFS: <refer doc/README.nand>
  CONFIG_CMD_SPL_NAND_OFS: <refer doc/README.falcon>
  CONFIG_SYS_NAND_SPL_KERNEL_OFFS: <refer doc/README.falcon>
  CONFIG_CMD_SPL_WRITE_SIZE: <refer doc/README.falcon>

This patch also updates documentation for few of above NAND configs.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25 16:26:12 -04:00
pekon gupta
867f03040f am335x: update README for BCH16
updates documentation with explanation on how to select ECC schemes.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:11 -04:00
pekon gupta
b80a660338 mtd: nand: omap: add CONFIG_SYS_NAND_BUSWIDTH_16BIT to indicate NAND device bus-width
GPMC controller needs to be configured based on bus-width of the NAND device
connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI
parameters is not possible in following situations:
SPL:    SPL NAND drivers does not support ONFI parameter reading.
U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init()
        which is called before probing for devices, hence any ONFI parameter
        information is not available during GPMC initialization.

Thus, OMAP NAND driver expected board developers to explicitely write GPMC
configurations specific to NAND device attached on board in board files itself.
But this was troublesome for board manufacturers as they need to dive into
lengthy platform & SoC documents to find details of GPMC registers and
appropriate configurations to get NAND device working.

This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config
hich indicates that connected NAND device has x16 bus-width. And then based on
this config GPMC driver itself initializes itself based on NAND bus-width. This
keeps board developers free from knowing GPMC controller specific internals.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:06 -04:00
pekon gupta
3f719069c8 mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme
This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed
CONFIG_xx used for selecting NAND ecc-schemes.
This patch aims at solving following issues.

1) Currently ecc-scheme is tied to SoC platform, which prevents user to select
   other ecc-schemes also supported in hardware. like;
 - most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite
   the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with
   software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW).
 - most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware
   supports BCH16 ecc-scheme also.

2) Different platforms use different CONFIG_xx to select ecc-schemes, which
   adds confusion for user while migrating platforms.
 - *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only
    8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW)
    whereas ELM hardware engine supports other ecc-schemes also like; BCH4,
    and BCH16 (in future).
 - *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error
    correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW).
 - *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library

Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency
on SoC platform and NAND driver. And user can select ecc-scheme independently
foreach board.
However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still
depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand)

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
pekon gupta
d016dc42ce mtd: nand: omap: enable BCH ECC scheme using ELM for generic platform
BCH8_ECC scheme implemented in omap_gpmc.c driver has following favours
+-----------------------------------+-----------------+-----------------+
|ECC Scheme                         | ECC Calculation | Error Detection |
+-----------------------------------+-----------------+-----------------+
|OMAP_ECC_BCH8_CODE_HW              |GPMC             |ELM H/W engine   |
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |GPMC             |S/W BCH library  |
+-----------------------------------+-----------------+-----------------+

Current implementation limits the BCH8_CODE_HW only for AM33xx device family.
(using CONFIG_AM33XX). However, other SoC families (like TI81xx) also have
ELM hardware module, and can support ECC error detection using ELM.

This patch
- removes CONFIG_AM33xx
	Thus this driver can be reused by all devices having ELM h/w engine.
- adds omap_select_ecc_scheme()
	A common function to handle ecc-scheme related configurations. This
	can be used both during device-probe and via user-space u-boot commads
	to change ecc-scheme. During device probe ecc-scheme is selected based
	on CONFIG_NAND_OMAP_ELM or CONFIG_NAND_OMAP_BCH8
- enables CONFIG_BCH
	S/W library (lib/bch.c) required by OMAP_ECC_BCHx_CODE_HW_DETECTION_SW
  	is enabled by CONFIG_BCH.
- enables CONFIG_SYS_NAND_ONFI_DETECTION
	for auto-detection of ONFI compliant NAND devices
- updates following README doc
	doc/README.nand
	board/ti/am335x/README
	doc/README.omap3

Signed-off-by: Pekon Gupta <pekon@ti.com>
[scottwood@freescale.com: fixed unused variable warning]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2013-11-21 13:33:41 -06:00
pekon gupta
beba5f04f2 mtd: nand: omap: make am33xx/elm.c as common driver for all OMAPx and AMxxxx platforms
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
	and include in all board configs using AM33xx SoC platform.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
Prabhakar Kushwaha
68ec9c85a9 mtd: move & update nand_ecclayout structure (plus board changes)
nand_ecclayout is present in mtd.h at Linux.
Move this structure to mtd.h to comply with Linux.

Also, increase the ecc placement locations to 640 to suport device having
writesize/oobsize of 8KB/640B. This means that the maximum oobsize has gone
up to 640 bytes and consequently the maximum ecc placement locations have
also gone up to 640.

Changes from Prabhabkar's version (squashed into one patch to preserve
bisectability):
 - Added _LARGE to MTD_MAX_*_ENTRIES

   This makes the names match current Linux source, and resolves
   a conflict between
   http://patchwork.ozlabs.org/patch/280488/
   and
   http://patchwork.ozlabs.org/patch/284513/

   The former was posted first and is closer to matching Linux, but
   unlike Linux it does not add _LARGE to the names.  The second adds
   _LARGE to one of the names, and depends on it in a subsequent patch
   (http://patchwork.ozlabs.org/patch/284512/).

 - Made max oobfree/eccpos configurable, and used this on tricorder,
   alpr, ASH405, T4160QDS, and T4240QDS (these boards failed to build
   for me without doing so, due to a size increase).

   On tricorder SPL, this saves 2576 bytes (and makes the SPL build
   again) versus the new default of 640 eccpos and 32 oobfree, and
   saves 336 bytes versus the old default of 128 eccpos and 8 oobfree.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Vipin Kumar <vipin.kumar@st.com>
[scottwood@freescale.com: changes as described above]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2013-11-21 13:32:43 -06:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Benoît Thébaudeau
3287f6d385 nand: Add torture feature
This patch adds a NAND Flash torture feature, which is useful as a block stress
test to determine if a block is still good and reliable (or should be marked as
bad), e.g. after a write error.

This code is ported from mtd-utils' lib/libmtd.c.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: removed unnec. ifdef and unwrapped error strings]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-11-26 15:41:29 -06:00
Joe Hershberger
eee623a504 nand: Add support for unlock.invert
NAND unlock command allows an invert bit to be set to unlock all but
the selected page range.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[scottwood@freescale.com: updated docs and added comment about invert bit]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-09-17 17:32:10 -05:00
Scott Wood
418396e212 nand: extend .raw accesses to work on multiple pages
A use for this is to read, modify, erase, and write an entire block as a
single unit, as a replacement for the biterr command.  This way gives
more flexibility in that you can also test multiple bit errors, errors
in the ECC, etc.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-05-18 17:34:31 -05:00
Scott Wood
578931b34d nand: Introduce CONFIG_SYS_NAND_SELF_INIT
This allows a driver to run code between nand_scan_ident() and
nand_scan_tail(), among other things.  See the additions to
doc/README.nand for details.

To allow a gradual transition, Boards that don't set
CONFIG_SYS_NAND_SELF_INIT will still be initialized the old way, but
new drivers should not require this, and existing drivers should be
converted when convenient.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26 16:09:06 -06:00
Marek Vasut
fb3659ac42 NAND: Add nand read.raw and write.raw commands
These commands should work around various "hardware" ECC and BCH methods.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: s/write the page/access the page/]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-10-03 18:35:12 -05:00
Ben Gardiner
c9494866df cmd_nand: add nand write.trimffs command
Add another nand write. variant, trimffs. This command will request of
nand_write_skip_bad() that all trailing all-0xff pages will be
dropped from eraseblocks when they are written to flash as-per the
reccommended behaviour of the UBI FAQ [1].

The function that implements this timming is the drop_ffs() function
by Artem Bityutskiy, ported from the mtd-utils tree.

[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_flasher_algo

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Artem Bityutskiy <dedekind1@gmail.com>
CC: Detlev Zundel <dzu@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-07-01 15:56:51 -05:00
Scott Wood
be33b046b5 Remove legacy NAND and disk on chip code.
Legacy NAND had been scheduled for removal.  Any boards that use this
were already not building in the previous release due to an #error.

The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed.  There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 19:07:47 -05:00
David Brownell
6e29ed8e57 davinci_nand: cleanup II (CONFIG_SYS_DAVINCI_BROKEN_ECC)
Remove CONFIG_SYS_DAVINCI_BROKEN_ECC option.  It's not just nasty;
it's also unused by any current boards, and doesn't even match the
main U-Boot distributions from TI (which use soft ECC, or 4-bit ECC
on newer chips that support it).

DaVinci GIT kernels since 2.6.24, and mainline Linux since 2.6.30,
match non-BROKEN code paths for 1-bit HW ECC.  The BROKEN code paths
do seem to partially match what MontaVista/TI kernels (4.0/2.6.10,
and 5.0/2.6.18) do ... but only for small pages.  Large page support
is really broken (and it's unclear just what software it was trying
to match!), and the ECC layout was making three more bytes available
for use by filesystem (or whatever) code.

Since this option itself seems broken, remove it.  Add a comment
about the MV/TI compat issue, and the most straightforward way to
address it (should someone really need to solve it).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-07 17:58:01 -05:00
Scott Wood
99067b08f4 Noisily disable the legacy NAND subsystem.
Legacy NAND is marked for feature removal after April 2009 (i.e. this
upcoming release).  There are still several boards that reference it
(though many do so only for disk-on-chip support which has been silently
disabled for a while now).  These boards will now fail to build
with #error, though the code is still there if the user removes #error.

The plan is to remove the code outright in the next release, along with
any board code that refers to it (such as board/esd/common/auto_update.c).

Also, remove the legacy NAND API description from README.nand.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-04-03 15:27:26 -05:00
Wolfgang Grandegger
6c869637fe NAND: rename NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define

 #define NAND_MAX_CHIPS          CONFIG_SYS_MAX_NAND_DEVICE

but that's bogus and did not work anyhow.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:51 -06:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Hugo Villeneuve
9b05aa788b ARM DaVinci: Fix broken HW ECC for large page NAND.
Based on original patch by Bernard Blackham <bernard@largestprime.net>

U-boot's HW ECC support for large page NAND on Davinci is completely
broken.  Some kernels, such as the 2.6.10 one supported by
MontaVista for DaVinci, rely upon this broken behaviour as they
share the same code for ECCs. In the existing scheme, error
detection *might* work on large page, but error correction
definitely does not.  Small page ECC correction works, but the
format is not compatible with the mainline git kernel.

This patch adds ECC code that matches what is currently in the
Davinci git repository (since NAND support was added in 2.6.24).
This makes the ECC and OOB layout written by u-boot compatible with
Linux for both small page and large page devices and fixes ECC
correction for large page devices.

The old behaviour can be restored by defining the macro
CFG_DAVINCI_BROKEN_ECC, which is undefined by default.

Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-09-10 11:40:30 -05:00
Jean-Christophe PLAGNIOL-VILLARD
cc4a0ceeac drivers/mtd/nand: Move conditional compilation to Makefile
rename CFG_NAND_LEGACY to CONFIG_NAND_LEGACY

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:43 +02:00
Scott Wood
984e03cdf1 NAND: Always skip blocks on read/write/boot.
Use of the non-skipping versions was almost always (if not always)
an error, and no valid use case has been identified.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:27 -05:00
Marcel Ziswiler
10c7382bc5 fix various comments
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2008-01-09 21:50:47 +01:00
Jon Loeliger
b5501f7d72 Update README.* to reference new CONFIG_CMD_* names now.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-07-09 19:10:03 -05:00
Stefan Roese
323bfa8f43 Remove BOARDLIBS usage completely
Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-23 12:00:22 +02:00
Stefan Roese
856f054410 [PATCH] NAND: Partition name support added to NAND subsystem
chpart, nboot and NAND subsystem related commands now accept also partition
name to specify offset.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2006-10-28 17:11:10 +02:00
Wolfgang Denk
fcfed4f2f2 Coding Style cleanup. 2006-10-18 22:44:38 +02:00
Stefan Roese
2255b2d204 * Several improvements to the new NAND subsystem:
- JFFS2 related commands implemented in mtd-utils style
  - Support for bad blocks
  - Bad block testing commands
  - NAND lock commands
  Please take a look at doc/README.nand for more details
  Patch by Guido Classen, 10 Oct 2006
2006-10-10 12:38:50 +02:00
Wolfgang Denk
bfc81252c0 Minor code cleanup 2006-03-06 13:03:37 +01:00
Wolfgang Denk
4e3ccd2692 Merge the new NAND code (testing-NAND brach); see doc/README.nand
Rewrite of NAND code based on what is in 2.6.12 Linux kernel
Patch by Ladislav Michl, 29 Jun 2005

[Merge with /home/tur/nand/u-boot]
2006-03-06 11:25:22 +01:00
wdenk
8bde7f776c * Code cleanup:
- remove trailing white space, trailing empty lines, C++ comments, etc.
  - split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)

* Patches by Kenneth Johansson, 25 Jun 2003:
  - major rework of command structure
    (work done mostly by Michal Cendrowski and Joakim Kristiansen)
2003-06-27 21:31:46 +00:00
wdenk
7a8e9bed17 * Patch by Marc Singer, 29 May 2003:
Fixed rarp boot method for IA32 and other little-endian CPUs.

* Patch by Marc Singer, 28 May 2003:
  Added port I/O commands.

* Patch by Matthew McClintock, 28 May 2003
  - cpu/mpc824x/start.S: fix relocation code when booting from RAM
  - minor patches for utx8245

* Patch by Daniel Engstrm, 28 May 2003:
  x86 update

* Patch by Dave Ellis, 9 May 2003 + 27 May 2003:
  add nand flash support to SXNI855T configuration
  fix/extend nand flash support:
  - fix 'nand erase' command so does not erase bad blocks
  - fix 'nand write' command so does not write to bad blocks
  - fix nand_probe() so handles no flash detected properly
  - add doc/README.nand
  - add .jffs2 and .oob options to nand read/write
  - add 'nand bad' command to list bad blocks
  - add 'clean' option to 'nand erase' to write JFFS2 clean markers
  - make NAND read/write faster

* Patch by Rune Torgersen, 23 May 2003:
  Update for MPC8266ADS board
2003-05-31 18:35:21 +00:00