Commit graph

25 commits

Author SHA1 Message Date
Rob Herring
32b4a8a2a5 ARM: highbank: remove DRAM bank setup
On the highbank platform the SoC's management controller firmware
will probe the DRAM modules and populates the initial device tree with
the correct values. Therefore the memory sizes in the DT are already
correct, so remove U-Boot's DRAM bank setup so the memory node is not
"fixed up" by u-boot.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andre Przywara <osp@andrep.de>
2015-08-12 12:08:19 -04:00
Joe Hershberger
ef0f2f5752 Move defaults from config_cmd_default.h to Kconfig
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25 22:18:34 -04:00
Stefan Roese
d126e01649 autoboot.c: Move config options to Kconfig
This patch moves the following config options to Kconfig:

CONFIG_AUTOBOOT_KEYED
CONFIG_AUTOBOOT_PROMPT
CONFIG_AUTOBOOT_DELAY_STR
CONFIG_AUTOBOOT_STOP_STR
AUTOBOOT_KEYED_CTRLC

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Drop ip04 and pm9263 configs/ additions, those boards previously
 set CONFIG_AUTOBOOT_PROMPT but never used it, re-run savedefconfig over
 all boards that did change. Make digsy_mtc_* string include seconds to
 match others and not warn. ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-06-08 17:32:16 -04:00
Rob Herring
46e09e6d1e ARM: highbank: convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD on highbank.

Signed-off-by: Rob Herring <robh@kernel.org>
2014-05-25 15:18:26 +02:00
Rob Herring
7904b70885 ARM: highbank: use default prompt
Since highbank is actually shared between Highbank and Midway platforms,
remove the Highbank name from the prompt and use the default.

Signed-off-by: Rob Herring <robh@kernel.org>
2014-05-02 11:43:25 +02:00
Rob Herring
ac9ae1333e ARM: highbank: use config_distro_defaults.h
Adapt highbank to use config_distro_defaults.h and remove the redundant
defines.

Signed-off-by: Rob Herring <robh@kernel.org>
2014-05-02 11:43:11 +02:00
Masahiro Yamada
e63510d1cb configs: clean up unused macro CONFIG_L2_OFF
Since commit c2dd0d455 and 45bf05854 introduced
the new cache maintainance framework to ARM,
CONFIG_L2_OFF has not been used at all.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-15 15:49:36 -05:00
Mark Langsdorf
2a19de42ec highbank: set AUTOBOOT_KEYED_CTRLC config option
Let highbank users break into the autoboot script with ctrl-c.

Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
2013-11-08 15:25:14 -05:00
Rob Herring
9df1bd416d ARM: highbank: convert to common timer code
Convert highbank to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:08:10 -05:00
Rob Herring
f232950f82 config: remove platform CONFIG_SYS_HZ definition part 2/2
Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:06:16 -05:00
Rob Herring
344ca0b40c ahci: convert to use libata functions and definitions
libata already has similar functions as implemented in the ahci code.
Refactor the code to use the libata variants and remove the dependency on
ata.h. Convert some defines to use the version from libata.h. Also, remove
some unnecessary memset's of bss data.

This is a step toward hopefully merging ahci.c and dw_ahsata.c which are
essentially the same driver.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-09-06 13:09:07 -04:00
Albert ARIBAUD
8b485ba12b Merge branch 'u-boot/master' into u-boot-arm/master 2013-07-25 17:57:46 +02:00
Rob Herring
76116f29ee highbank: enable keyed autoboot stop
Restrict autoboot interruption to "s" or "d" keys. This will prevent some
unwanted stopping and also allow disabling the reset on command timeout.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25 08:16:37 +02:00
Rob Herring
76c3999db4 ARM: highbank: setup peripherals based on power domain status
Accessing powered down peripherals will hang the bus, so check power
domain status before initializing SATA and fixup the FDT to disable
unused peripherals.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25 08:16:07 +02:00
Rob Herring
e1df283c26 ARM: highbank: enable reset on command timeout
Enable resetting on command timeout. The timeout is set with environment
setting bootretry.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25 08:15:57 +02:00
Rob Herring
185a5bb0f5 ARM: highbank: update config options
Various changes to highbank config:

Enable EFI partitions
Enable ext4 and FAT filesystems
Enable bootz command and raw initrd
Increase cmd and print buffer size to 1K
Change serial baudrate to 115200
Enable hush shell

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-07-25 08:15:02 +02:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Rob Herring
3d6ba91e79 ARM: Remove unused stack and irq config defines
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.

IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-09-01 14:58:22 +02:00
Stefan Roese
0044c42e94 Consolidate bootcount code into drivers/bootcount
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-09-01 14:26:02 +02:00
Tom Rini
26750c8aee CONFIG_SYS_BAUDRATE_TABLE: Add <config_fallbacks.h>, place there
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file.  This is used when a board has not set its
own table.

Signed-off-by: Tom Rini <trini@ti.com>
2012-06-20 20:26:16 +02:00
Jason Hobbs
a34e854948 ARM: highbank: change env config to use nvram
Update the highbank config to use env from NVRAM. Also remove extra env
settings as they are not used unless the default env is used.

Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28 23:34:13 +02:00
Rob Herring
877012df30 ARM: highbank: Add boot counter support
Add boot counter support using an sysreg which is persistent across reset.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28 23:31:20 +02:00
Rob Herring
7b81649a05 ARM: highbank: change TEXT_BASE to 0x8000
Make some space at the beginning of RAM so the FDT can be loaded to a
known fixed address at 0x1000.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-03-28 23:31:12 +02:00
Rob Herring
9a420986cc ARM: highbank: enable networking and pxe
This enables the XGMAC ethernet driver and networking related config
options.

Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-01-05 20:10:38 +01:00
Rob Herring
37fc0ed268 ARM: Add Calxeda Highbank platform
Add basic support for Calxeda Highbank platform. Only minimal support with
serial and SATA are included.

Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-10-27 21:56:37 +02:00