Commit graph

567 commits

Author SHA1 Message Date
Stefan Roese
492d3223b0 mmc: sdhci.c: Add config option to use a fixed buffer for transfers
While implementing SDIO/MMC SPL booting for the Marvell Armada 38x, the
following problem occured. The SPL runs in internal SRAM which is
the L2 cache locked to memory. When the MMC buffers now are located
on the stack (or bss), the SDIO controller (SDHCI) can't write into
this L2 cache memory.

This patch introduces a method to use a fixed buffer that will be
used for all transfers by defining CONFIG_FIXED_SDHCI_ALIGNED_BUFFER.
This way, the board can use this buffer address located in SDRAM
for all transfers. This solves this SPL problem on the A38x and
should only be used in the SPL U-Boot version.

Tested for SPL booting on Marvell Armada 38x DB-88F6820-GP board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-07-10 14:54:05 +02:00
Stefan Roese
29905a451b mmc: sdhci: Use timer based timeout detection in sdhci_send_command()
The loop counter based timeout detection does not work on the Armada
38x based board (DB-88F6820-GP). At least with dcache enabled a
timeout is detected. Without dcache enabled, the timeout does not
occur. Increasing the loop counter solves this issue. But a better
solution is to use a timer based timeout detection instead. This
patch now implements this timer based detection.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-07-10 14:54:00 +02:00
Marek Vasut
9f1b4456c9 mmc: bcm2835_sdhci: Restore original delay behavior
Patch 33fe2fb8df titled
"mmc: bcm283x: Remove get_timer_us() from mmc driver"
incorrectly replaced ad-hoc get_timer_us() function
with a plain get_timer(). The get_timer() operates in
mSec units instead of uSec though, which caused very
slow operation of the driver.

Restore the original behavior of the driver, but avoid
get_timer_us() and use timer_get_us() instead. The later
is part of the standard API.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jakub Kiciński <moorray3@wp.pl>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Jakub Kicinski <kubakici@wp.pl>
2015-06-25 17:04:37 -04:00
Tom Rini
180f87fcc5 mmc_write.c: Make mmc_berase do 32bit safe 64bit math
We want to see if the requested start or total block count are
unaligned.  We discard the whole numbers and only care about the
remainder.  Update the code to use div_u64_rem here and add a comment.

Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Bernhard Nortmann <bernhard.nortmann@web.de>
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
2015-06-18 16:11:41 -04:00
Hans de Goede
1c09fa38e0 sunxi: mmc: Enable pull-up on card-detect gpio pin
On some boards we need to enable the internal pull-up te reliable detect
that no card is inserted.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-06-04 14:08:28 +02:00
Tom Rini
d81572c272 Merge git://git.denx.de/u-boot-mpc85xx 2015-05-05 14:57:23 -04:00
Tom Rini
ff7e9cfc33 Merge branch 'master' of git://git.denx.de/u-boot-mmc 2015-05-05 07:00:38 -04:00
Marek Vasut
33fe2fb8df ARM: mmc: bcm283x: Remove get_timer_us() from mmc driver
The get_timer_us() function is something which is no longer
existing in case we use generic timer framework, so replace
it with get_timer().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tyler Baker <tyler.baker@linaro.org>
2015-05-05 12:29:42 +03:00
Simon Glass
707ac1ad17 tegra: mmc: Set the removable flag correctly
If the mmc device is non-removable (as indicated by the device tree), set
the flag so that users of the device know.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2015-05-05 12:29:42 +03:00
Alexander Stein
ebe78bb993 mmc: bcm2835_sdhci: Use calloc to allocate bcm2835_sdhci_host
We need to clear the allocated memory explicitly as the included
struct sdhci_host has function pointers. Those are compared to NULL to
test if this (optional) feature is supported. Leaving them undefined let
u-boot jump to arbitrary memory.

Signed-off-by: Alexander Stein <alexanders83@web.de>
2015-05-05 12:29:42 +03:00
Yangbo Lu
253d5bdd64 mmc: fsl_esdhc: update eMMC44 adapter card erase timeout
Freescale eMMC44 adapter card uses Micron N2M400FDB311A3CF eMMC
memory. According to the silicon datasheet, secure erase timeout
is 600ms. So increase erase timeout value from 250ms to 600ms.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
2015-05-05 12:29:42 +03:00
Kevin Liu
5e1c23cd39 mmc: sdhci: add timeout setting for response busy command
Timeout interrupt also work for response busy command(R1b) like
cmd38/cmd6. So need to set it accordingly. Current code only
set timeout for data command.

Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-05-05 12:29:42 +03:00
Rob Herring
5a20397b00 mmc: remove the MMC_MODE_HC flag
High capacity support is not a host capability, but a device capability
that is queried via the OCR. The flag in the operating conditions
request argument can just be set unconditionally. This matches the Linux
implementation.

[panto] Hand merged and renumbering MMC_MODE_DDR_52MHz.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
2015-05-05 12:29:36 +03:00
Andrew Gabbasov
bd47c13583 mmc: Fix splitting device initialization
Starting part of device initialization sets the init_in_progress flag
only if the MMC card did not yet come to ready state and needs to continue
polling. If the card is SD or if the MMC card became ready quickly,
the flag is not set and (if using pre-initialization) the starting
phase will be re-executed from mmc_init function.

Set the init_in_progress flag in all non-error cases. Also, move flags
setting statements around so that the flags are not set in error paths.
Also, IN_PROGRESS return status becomes unnecessary, so get rid of it.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:55:46 +03:00
Andrew Gabbasov
1677eef459 mmc: Restructure polling loops to avoid extra delays
The polling loops in sd_send_op_cond and mmc_complete_op_cond functions
check the ready flag state at the end of the loop, that is after executing
a delay inside the loop, which, in case of exiting with no error,
is not needed. Also, one of these loops, as well as the loop
in mmc_send_status, have the delay just before exiting on timeout
conditions.

Restructure all these loops to check the respective conditions before making
a delay for the next loop pass, and to appropriately exit without the delay.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:55:00 +03:00
Andrew Gabbasov
cc17c01f2d mmc: Continue polling MMC card for OCR only if it is still not ready
Some MMC cards come to ready state quite quickly, so that the respective
flag appears to be set in mmc_send_op_cond already. In this case trying
to continue polling the card with CMD1 in mmc_complete_op_cond is incorrect
and may lead to unpredictable results. So check the flag before polling
and skip it appropriately.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:54:40 +03:00
Andrew Gabbasov
5289b5350b mmc: Do not pass external mmc_cmd structure to mmc_send_op_cond_iter()
The previous change to use 'ocr' structure field for storing send_op_cond
command response also stopped using command response directly
outside of mmc_send_op_cond_iter(). Now it becomes possible to use
command structure in mmc_send_op_cond_iter() locally, removing a necessity
to pass it as an argument from the caller.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:54:09 +03:00
Andrew Gabbasov
a626c8d418 mmc: Avoid extra duplicate entry in mmc device structure
The 'op_cond_response' field in mmc structure contains the response
from the last SEND_OP_COND MMC command while making iterational
polling of the card. Later it is copied to 'ocr' field, designed
to contain the OCR register value, which is actually the same
response from the same command. So, these fields have actually
the same data, just in different time periods. It's easier to use
the same 'ocr' field in both cases at once, without temporary using
of the 'op_cond_response' field.

Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
2015-05-05 11:53:52 +03:00
Yangbo Lu
2d9ca2c72c mmc: fsl_esdhc: Add peripheral clock support
The SD clock could be generated by platform clock or peripheral
clock for some platforms. This patch adds peripheral clock
support for T1024/T1040/T2080. To enable it, define
CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:25:39 -07:00
Yangbo Lu
5a8dbdc6b4 mmc: fsl_esdhc: Add adapter card type identification support
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:25:19 -07:00
Hans de Goede
90641f82f1 sunxi: mmc: Fix card-detect gpio handling to work with the driver-model
The driver-model gpio functions may return another value then -1 as error,
make the sunxi mmc code properly handle this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:52 +02:00
Hans de Goede
44d8ae5b69 sunxi: Introduce a hidden SUNXI_GEN_SUNxI Kconfig bool
sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i
have a various things in common, like having separate ahb reset control
registers, the SID living inside the pmic, custom pmic busses, new style
watchdog, etc.

This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be
used to check for these features avoiding the need for an ever growing list
of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more
"new style" sunxi SoCs.

Note that this commit changes the behavior of the gmac and hdmi code for
sun8i and the upcoming sun9i devices. This does not matter as sun8i does
not have gmac nor hdmi, and sun9i has new hardware-blocks for these so
the old code will not work there.

Also this is intentional as if a sun8i / sun9i variant which does use the
old hwblocks shows up then the GEN_SUN6I code paths will be the right ones
to use.

For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Siva Durga Prasad Paladugu
eddabd1662 zynqmp: sdhci: Remove the quirk SDHCI_QUIRK_NO_CD
Remove the quirk SDHCI_QUIRK_NO_CD as it is not
required.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-29 11:19:03 +02:00
Yangbo Lu
8b06460e55 ls2085a: esdhc: Add esdhc support for ls2085a
This patch adds esdhc support for ls2085a.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 16:46:51 -07:00
Masahiro Yamada
d6c418e4b8 ARM: bcm283x: move SoC headers to mach-bcm283x/include/mach
Move arch/arm/include/asm/arch-bcm283x/*
  -> arch/arm/mach-bcm283x/include/mach/*

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
2015-03-28 09:03:09 -04:00
Rob Herring
3a48944bc9 mv_sdhci: fix warnings on 64-bit builds
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-03-18 09:56:17 +02:00
Rob Herring
3c1fcb770b sdhci: fix warnings on 64-bit builds
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-03-18 09:55:59 +02:00
Matt Reimer
e113fe3c06 mmc: sdhci: don't clobber adjacent registers
SDHCI_HOST_CONTROL is a byte-sized register, so don't write to it
as if it were a long, as that would result in clobbering the three
registers following.

Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
2015-03-18 09:53:01 +02:00
Matt Reimer
8ebde4f0b3 mmc: s5p: properly mask SELBASECLK
Properly mask SELBASECLK by using an actual mask rather than the
number of bits to shift in order to create the mask.

Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-03-18 09:51:56 +02:00
Peng Fan
323aaaa1e3 mmc: fsl_esdhc fix register offset
Commit f022d36e8a introduces
error register offset.

Change the "char reserved3[59]" to "char reserved3[56]".

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-03-17 09:09:47 -04:00
Stefano Babic
b9cb64825b Merge branch 'master' of git://git.denx.de/u-boot 2015-03-02 09:42:53 +01:00
Volodymyr Riazantsev
0e1bf614d5 mmc: fsl_esdhc: Add support for DDR mode
Add support of the DDR mode for eSDHC driver.
Enable it for i.MX6 SoC family only.

Signed-off-by: Volodymyr Riazantsev <volodymyr.riazantsev@globallogic.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24 13:11:10 -08:00
Matt Reimer
f88a429f11 mmc: sdhci: fix bus width switching on Samsung SoCs
Fix bus width switching from 8-bit mode down to 4-bit or 1-bit modes on
Samsung SoCs using SDHCI_QUIRK_USE_WIDE8.  These SoCs report controller
version 2.0 yet they support 8-bit bus widths.  If 8-bit mode was
previously enabled and then an operation like "mmc dev" caused a switch
back down to 4-bit or 1-bit mode, WIDE8 was left set, causing failures.

This problem was manifested by "mmc dev" timing out.

Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
2015-02-23 19:52:00 +02:00
Przemyslaw Marczak
34dd928492 mmc: print SD/eMMC type for inited mmc devices
Depending on the boot priority, the eMMC/SD cards,
can be initialized with the same numbers for each boot.

To be sure which mmc device is SD and which is eMMC,
this info is printed by 'mmc list' command, when
the init is done.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2015-02-23 19:49:49 +02:00
Przemyslaw Marczak
64029f7aee mmc: exynos dwmmc: check boot mode before init dwmmc
Before this commit, the mmc devices were always registered
in the same order. So dwmmc channel 0 was registered as mmc 0,
channel 1 as mmc 1, etc.
In case of possibility to boot from more then one device,
the CONFIG_SYS_MMC_ENV_DEV should always point to right mmc device.

This can be achieved by init boot device as first, so it will be
always registered as mmc 0. Thanks to this, the 'saveenv' command
will work fine for all mmc boot devices.

Exynos based boards usually uses mmc host channels configuration:
- 0, or 0+1 for 8 bit  - as a default boot device (usually eMMC)
- 2 for 4bit - as an optional boot device (usually SD card slot)

And usually the boot order is defined by OM pin configuration,
which can be changed in a few ways, eg.
- Odroid U3     - eMMC card insertion -> first boot from eMMC
- Odroid X2/XU3 - boot priority jumper

By this commit, Exynos dwmmc driver will check the OM pin configuration,
and then try to init the boot device and register it as mmc 0.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
2015-02-23 19:49:22 +02:00
Hans de Goede
1f3e877def sunxi: mmc: Always declare High Capacity capability
High Capacity (e)MMC cards work fine on sun4i / sun5i, and not having this
capability set causes u-boot to not recognize the eMMC on an Utoo P66 A13
tablet, so always set it thereby fixing this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-23 19:46:13 +02:00
Jaehoon Chung
5dab81cea5 mmc: exynos_dw_mmc: use the exynos specific data structure
Clksel value is exynos specific value.
It removed "clksel_val" into dwmci_host and created the
"dwmci_exynos_priv_data" structure for exynos specific data.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-02-23 19:39:51 +02:00
Jaehoon Chung
3a33bb1874 mmc: exynos_dw_mmc: set to clksel_val into board-init function
"clksel_val" is assigned to property of mmc or defined value.
But it doesn't write at initial sequence.
There is a reason that get the wrong source-clock value.
This patch fixed it.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-02-23 19:36:55 +02:00
Jaehoon Chung
afc9e2b509 mmc: dw_mmc: fixed the wrong bit control
If mode is not DDR-mode, then it needs to clear it.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-02-23 19:35:13 +02:00
Otavio Salvador
ee0c538951 mmc: fsl_esdhc: Add support to force VSELECT set
Some boards cannot do voltage negotiation but need to set the VSELECT
bit forcely to ensure it to work at 1.8V.

This commit adds CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT flag for this use.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2015-02-23 09:11:42 +01:00
Otavio Salvador
f022d36e8a mmc: fsl_esdhc: Add CMD11 support to switch to 1.8V
This adds support to switch to 1.8V in case CMD11 succeeds.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Marek Vasut <marex@denx.de>
2015-02-23 09:11:42 +01:00
Simon Glass
91785f70b9 x86: mmc: Move common FSP functions into a common file
Since these board functions seem to be the same for all boards which use
FSP, move them into a common file. We can adjust this later if future FSPs
need more flexibility.

This creates a generic PCI MMC device.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2015-02-06 12:07:36 -07:00
Tom Rini
37ffffb98d Merge branch 'master' of git://git.denx.de/u-boot-ti 2015-02-02 12:37:34 -05:00
Tom Rini
be8ddad9c8 Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2015-02-02 10:11:44 -05:00
Siarhei Siamashka
5abdb156bb sunxi: mmc: Add 'sunxi_' prefix to the static functions
This results in a much more readable callgraph, because now they
can't be confused with the function having exactly the same name
in the generic mmc code.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-02 14:04:28 +01:00
Simon Glass
0347960b87 dm: mmc: Remove use of fdtdec GPIO support
These functions are going away, so use the new uclass support instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:52 -07:00
Albert ARIBAUD \(3ADEV\)
5bfdd1fc97 omap3: mmc: add 1.8v bias setting for MMC1
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-01-29 12:00:50 -05:00
Tom Rini
3b95288a2a Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2015-01-23 10:22:29 -05:00
Hans de Goede
daf22636c2 sunxi: mmc: Add support for sun9i (A80)
The clocks on the A80 are hooked up slightly different, add support for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Hans de Goede
5b8d7fb4fe sunxi: mmc: Use a realistic timeout when sending a mmc command
Wait 1 second for the sdcard to respond, rather then waiting for
0xfffff milliseconds.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00