Commit graph

30 commits

Author SHA1 Message Date
Joe Hershberger
0adb5b761f net: cosmetic: Name ethaddr variables consistently
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:32 -06:00
Khoronzhuk, Ivan
3e01ed00da mtd: nand: davinci: add header file for driver definitions
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-19 17:53:58 -04:00
Christian Riesch
3864cb2133 da850evm: Use clrbits function with correct endianess
The current code uses clrbits_be32 which is incorrect since we are on
a little endian machine here. This patch fixes this issue and also removes
some unnecessary code: Reading the current GPIO bank state is not required
if we are using the SET and CLEAR GPIO registers for setting/clearing
bits.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Cc: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
2013-07-26 16:39:10 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Lad, Prabhakar
de94b80d3c da850/omap-l138: Fix NAND flash timings
Though Commit id a3f88293dd (da850evm:
setup the NAND flash timings) has configured the AEMIF timings, they
are not exactly in sync with the timings used in Linux. Linux is
configuring the timing register as 0x08222204, where as currently it
configured to 0x00100084 in U-Boot. This issue was found out when
support for NAND SPL is added in U-Boot. Without this patch U-Boot
does not come up with SPL.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
2012-09-01 14:58:09 +02:00
Rajashekhara, Sudhakar
6652c62e01 da850/omap-l138: modifications for Logic PD Rev.3 AM18xx EVM
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
MMC and NOR to work on DA850/OMAP-L138 Rev.3 EVM. When
GP0[11] is low, the SD0 interface will not work, but NOR
flash will. When GP0[11] is high, SD0 will work but NOR
flash will not.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
2012-09-01 14:58:09 +02:00
Lad, Prabhakar
ecc98ec18c da850/omap-l138: Add MMC support for DA850/OMAP-L138
This patch adds support for MMC/SD on DA850/OMAP-L138.

Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
2012-09-01 14:58:09 +02:00
Hadli, Manjunath
206a1038f7 da850evm: read mac address from I2C EEPROM on AM18x EVM
add support to read mac address for AM18x EVM manufactured from
Spectrum digital which have mac address stored in I2C EEPROM manufactured
by WINBOND. This patch reads mac address from I2C EEPROM and sets the
environment variable if not set, If mac address is already present in
environment compare it with the mac address in EEPROM and warn on
mismatch.Introduced a config option CONFIG_MAC_ADDR_IN_EEPROM to where
to look for the mac address.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Wolfgang Denk <wd@denx.de>
2012-02-27 21:19:24 +01:00
Hadli, Manjunath
38fed6ee95 da850evm: add support to read mac address from SPI flash
add support to read mac address for da850/L138 evm manufactured by
Logic PD which store mac address in SPI flash manufactured by ST
Microelectronics. This patch adds support to read mac address from
SPI flash and set the mac address if it hasn't been set in environment,
If it has been set in the environment it compares the value one with
SPI flash and warns on mismatch. Introduced a config option
CONFIG_MAC_ADDR_IN_SPIFLASH indicating where to look mac address for.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Wolfgang Denk <wd@denx.de>
2012-02-27 21:19:24 +01:00
Sughosh Ganu
6b873dcabd Changes to move hawkboard to the new spl infrastructure
This patch moves hawkboard to the new spl infrastructure from the
older nand_spl one.

Removed the hawkboard_nand_config build option -- The spl code now
gets compiled with hawkboard_config, after building the main u-boot
image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard
to reflect the same.

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
2012-02-12 10:11:33 +01:00
Christian Riesch
3d2c8e6c7f arm, da850evm: Add an SPL for SPI boot
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
2011-12-24 10:23:30 +01:00
Manjunath Hadli
754f8cb689 da850evm: pass board revision info to kernel
there are two boards based on da850 SOC - OMAP-L138 and AM18x.
In order to differentiate between these two boards, revision id
is passed to kernel via second byte of ATAG_REVISION.

Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
2011-12-06 23:59:40 +01:00
Christian Riesch
52b0f877a2 arm, da850evm: Use the pinmux configurations defined in the arch tree
The boards in board/davinci/da8xxevm/ define pinmux_config[] vectors
that contain pinmux configurations for emac, uarts, memory controllers...
In an earlier patch such pinmux configurations were added to the arch
tree. This patch makes the da850evm use these definitions instead of
defining its own.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Heiko Schocher <hs@denx.de>
2011-12-06 23:59:36 +01:00
Christian Riesch
591d8019a1 arm, da850evm: Do pinmux configuration for EMAC together with other pinmuxes
Pinmux configuration for the EMAC was done in a separate call
of davinci_configure_pin_mux(). This patch moves all the pinmux
configuration that is done for this board to a common place.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
2011-12-06 23:59:36 +01:00
Christian Riesch
964930bcfd arm, davinci: Move pinmux functions from board to arch tree
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Nick Thompson <nick.thompson@ge.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Nick Thompson <nick.thompson@ge.com>
2011-12-06 23:59:36 +01:00
Christian Riesch
ae5c77dd90 da850evm: Move LPSC configuration to board_early_init_f()
Since commit f1d2b313c9 the serial
port of the da850evm is accessed before the UART2 peripheral of
the SoC is powered on in the function board_init() in
board/davinci/da8xxevm/da850evm.c.

When u-boot is used in conjunction with the UBL (user boot loader, see
doc/README.davinci) on this board, the UART2 peripheral is already
turned on by UBL at the time u-boot is started. Hence, the wrong
initialization sequence is not noticed by most users. However, if UBL is not
used, u-boot must power on the peripheral before using it.

This patch adds a board_early_init_f() function for the LPSC
configuration to the da850evm board configuration.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:36 +02:00
Wolfgang Denk
6f0d7ae265 da8xxevm: Fix warning: unused variable 'val'
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
2011-09-07 22:02:07 +02:00
Nagabhushana Netagunte
0f3d6b06ea da850: modifications for Logic PD Rev.3 AM18xx EVM
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
NOR to work on Rev.3 EVM. When GP0[11] is low,
the SD0 interface will not work, but NOR flash will.

Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04 11:36:19 +02:00
Nagabhushana Netagunte
cf2c24e399 da850: add support to wake up DSP during board init
add support for DSP wake-up by default on DA850/OMAP-L138
during board initialization. Enable hwconfig environment and added
extra env setting through CONFIG_EXTRA_ENV_SETTINGS.
To prevent DSP from being woken up,set the environment variable as,
set hwconfig "dsp:wake=no"

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04 11:36:19 +02:00
Nagabhushana Netagunte
1506b0a837 da850: add NOR boot mode support
Add pin-mux support for NOR in board file and correspanding
macros to use NOR boot mode in configuration file.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04 11:36:19 +02:00
Ben Gardiner
24a514c445 da850evm: fix NAND WSTROBE and TA timings
The current NAND timings, introduced in commit
a3f88293dd da850evm: setup the NAND flash
timings , incorrectly set WSTROBE and TA to 0. A more recent inspection of the
values set by the Linux kernel indicates that these should be set to 1.

Set the WSTROBE and TA field of the EMIFA cycle-count timings configuration to
1 to match the values set by linux.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Stefano Babic <sbabic@denx.de>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-05-11 23:03:15 +02:00
Stefano Babic
6d1c649f44 Davinci 8xx: Move common functions to share code
As more Davinci 8xx board can be added, move common code
to be shared between boards.

 * rebased ontop of Sugosh's patches
 * moving the HAWKBOARD_KICK{0,1}_UNLOCK defines to
   arch/arm/include/asm/arch-davinci/davinci_misc.h from to
   arch/arm/include/asm/arch-davinci/da8xx_common.h
 * don't define dram functions in PRELOADER
 * move sync_env_enetaddr into existing EMAC ifdef
 * use misc.c in hawkboard nand_spl

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-30 11:32:59 -05:00
Sudhakar Rajashekhara
d26074012b da850: Add RMII support for EMAC
This patch is a port of the work by Sudhakar Rajeshekhara in commit
ab3effbcad8851cc65dc5241a01c064d2030a3b2 of
git://arago-project.org/git/people/sandeep/u-boot-davinci.git.

The da850 UI board has on it an RMII PHY which can be used if the MDC line
to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by
configuring the values of some GPIO pins on the IO expander of the UI board.
This patch implements disabling that line via GPIO2[6], configuring the UI
board's IO expander and setting only the pinmux settings that are needed for
RMII operation.

Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-30 11:27:44 -05:00
Sughosh Ganu
d7f9b503a8 Move and rename common headers from under
board/davinci.

 Move the davinci common headers to the architecture specific
 include file path.

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-28 20:21:27 -05:00
Sekhar Nori
4f6fc15b42 DA850 EVM: passing maximum clock rate information to kernel
The TI DA850/OMAP-L138/AM18x EVM can be populated with devices
having different maximum allowed CPU clock rating.

The maximum clock the chip can support can only be determined from
the label on the package (not software readable).

Introduce a method to pass the maximum allowed clock rate information
to kernel using ATAG_REVISION. The kernel uses this information to
determine the maximum cpu clock rate reachable using cpufreq.

Note that U-Boot itself does not set the CPU clock rate. The CPU
clock is setup by a primary bootloader ("UBL"). The rate setup by
UBL could be different from the maximum clock rate supported by the
device.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-19 16:29:11 -05:00
Ben Gardiner
3d248d37e1 da850evm: basic MII EMAC support
The current da850evm support in u-boot/master omits any use of
the davinci EMAC. This patch adds basic support for the EMAC using
the MII PHY found on the baseboard of the EVM. The MAC address is
read from the environment variable 'ethadd'. Note that this is
different from the da850evm support in the u-boot omapl1 tree
where the MAC address is read from SPI flash.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-10-17 20:14:55 +02:00
Ben Gardiner
a3f88293dd da850evm: setup the NAND flash timings
The default NAND flash timings are very conservative. This patch assigns the
timings reccomended in the recent linux kernel patch [1] from Sekhar Nori. The
speedup, as reported in that patch, is 5.3x for reads.

[1] http://www.spinics.net/lists/arm-kernel/msg100278.html

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-10-17 20:14:47 +02:00
Ben Gardiner
756d1fe7ac da850evm : enable NAND even when not in NAND boot mode
There is currently no NAND pinmux enabled by the da850evm board setup code.
This is fine when booting from NAND since the early boot code (UBL) will setup
the pinmux; however, when the boot mode is any other setting NAND is unusable
when enabled in the config.

This patch adds a pinmux list for NAND and enables it when NAND is enabled in
the config. Tested by booting from SPI on the da850evm and verifying NAND
was usable.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-10-17 20:14:45 +02:00
Prakash PM
37adbf9b12 da850 evm: Fix definition of 'pinmux' macro
Usage of parenthesis in pinmux macro definition changes the
definition of the macro and raises the precedence of '&'
operator inadvertently over '[]'.

Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-15 16:08:38 -04:00
Sudhakar Rajashekhara
89b765c7f6 TI: DaVinci: Add board specific code for da850 EVM
Provides initial support for TI OMAP-L138/DA850 SoC devices on
a Logic PD EVM board.

Provides:
Initial boot and configuration.
Support for i2c.
UART support (console).

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-10 12:04:42 -04:00