Commit graph

501 commits

Author SHA1 Message Date
Yunhui Cui
04e5c6d9cc driver: spi: fsl-qspi: remove compile Warnings
Warnins log:
drivers/spi/fsl_qspi.c: In function ‘qspi_ahb_read’:
drivers/spi/fsl_qspi.c:400:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  memcpy(rxbuf, (u8 *)(priv->cur_amba_base + priv->sf_addr), len);

Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02 09:45:13 -07:00
Vignesh R
a6f56ad1ee spi: ti_qspi: dra7xx: Add support to use 76.8MHz clock
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, update
the driver to use the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
fee3b6af90 spi: ti_qspi: Remove delay in read path for dra7xx
As per commit b545a98f5d ("spi: ti_qspi: Add delay
for successful bulk erase) says its added to meet bulk erase timing
constraints. But bulk erase is a cmd to flash and delay in read path
does not make sense. Morever, testing on DRA74/DRA72 evm has shown that
this delay is no longer required.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
c595a28530 spi: ti_qspi: Fix compiler warning when DEBUG macro is set
clk_div is uninitialized at the beginning of ti_spi_set_speed(), move
debug() print after clk_div calculation to avoid compiler warning and to
have proper value of clk_div printed during debugging.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
69eeefaa06 spi: ti_qspi: Fix failure on multiple READ_ID cmd
Populating QSPI_RD_SNGL bit(0x1) in priv->cmd means that value
QSPI_INVAL (0x4) is not written to CMD field of QSPI_SPI_CMD_REG in
ti_qspi_cs_deactivate(). Therefore CS is never deactivated between
successive READ ID which results in sf probe to fail.
Fix this by not populating priv->cmd with QSPI_RD_SNGL and OR it wih
priv->cmd as required (similar to the convention followed in the
driver).

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Simon Glass
911954859d dm: Use dm_scan_fdt_dev() directly where possible
Quite a few places have a bind() method which just calls dm_scan_fdt_dev().
We may as well call dm_scan_fdt_dev() directly. Update the code to do this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:54 -06:00
Simon Glass
2e3f1ff63f dm: Convert users from dm_scan_fdt_node() to dm_scan_fdt_dev()
This new function is more convenient for callers, and handles pre-relocation
situations automatically.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-27 14:15:07 -06:00
Vignesh R
96907c0fe5 dm: spi: Read default speed and mode values from DT
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_*, instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:34 +05:30
Vignesh R
2372e14f19 spi: cadence_quadspi: Enable QUAD mode based on DT data
Instead of relying on CONFIG_SPI_FLASH_QUAD to be defined to enable QUAD
mode, make use of mode_rx field of dm_spi_slave_platdata to determine
whether to enable or disable QUAD mode. This is necessary to support
muliple SPI controllers where one of them may not support QUAD mode.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:33 +05:30
Vignesh R
dac3bf20fb spi: cadence_qspi_apb: Support 32 bit AHB address
AHB address can be as long as 32 bit, hence remove the
CQSPI_REG_INDIRECTRDSTARTADDR mask. Since AHB address is passed from DT
and read as u32 value, it anyway does not make sense to mask upper bits.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:32 +05:30
Vignesh R
192bb756dc spi: davinci_spi: Convert to driver to adapt to DM
Convert davinci_spi driver so that it complies with SPI DM framework.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:30 +05:30
Anatolij Gustschin
c8864d7209 spi: spi-uclass: fix typo in debug output
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-06 12:40:32 +05:30
Praneeth Bajjuri
8dfd6e2129 driver: qspi: correct QSPI disable CS reset value
Correcting QSPI disable/unselect CS reset value.
CTRL_CORE_CONTROL_IO_2: QSPI_MEMMAPPED_CS[10:8]

This is not causing any issue, but its better
to untouch the reserved bits.

Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
2016-07-01 17:42:53 -04:00
Stephen Warren
135aa95002 clk: convert API to match reset/mailbox style
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
  provider now implements a single set of clocks. This provides a simpler
  conceptual interface to clients, and better aligns with device tree
  clock bindings.
* Clocks are now identified with a single "struct clk", rather than
  requiring clients to store the clock provider device and clock identity
  values separately. For simple clock consumers, this isolates clients
  from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
  clk-uclass.h contains the provider API. This aligns with the recently
  added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
  can customize these operations if needed. This also aligns with the
  recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
  clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.

Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.

test/py passes for sandbox (which invokes the dm clk test amongst
others).

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-06-19 17:05:55 -06:00
Purna Chandra Mandal
e19b900457 spi: pic32_spi: add SPI master driver for PIC32 SoC.
This driver implements SPI protocol in master mode to communicate
with the SPI device connected on SPI bus. It handles /CS explicitly
by controlling respective pin as gpio ('cs-gpios' property in dt node)
and uses PIO mode for SPI transaction. It is configurable based
on driver-model only.

Cc: Jagan Teki <jteki@openedev.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-06-10 12:31:12 +02:00
Tom Rini
fc15b9beed Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-05-24 13:42:03 -04:00
Tom Rini
d7d0003112 Merge branch 'master' of git://git.denx.de/u-boot-mips 2016-05-23 11:51:37 -04:00
Martin Hejnfelt
5f89a15e16 omap3: Fix SPI registers on am33xx and am43xx
When the base registers are read from device tree the base is not
0x48030100 as the driver expects, but 0x48030000, resulting in
non functioning SPI. To deal with this, use same idea as how this
is done in the linux kernel (drivers/spi/spi-omap2-mcspi.c) and
add a structure with a field that is used to shift the registers
on these systems.

v2: Fixed commit subject line to correct cpu

Signed-off-by: Martin Hejnfelt <mh@newtec.dk>
2016-05-23 11:50:22 -04:00
Wills Wang
5fabf2e7da ath79: spi: Remove the explicit pinctrl setting
The correct pinctrl is handled automatically so we don't need to do it in
the driver.

Signed-off-by: Wills Wang <wills.wang@live.com>
2016-05-21 01:36:37 +02:00
Wills Wang
b85dc46072 drivers: spi: add spi support for QCA/Atheros ath79 SOCs
This patch add a compatible spi driver for ath79 series SOC.

Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-21 01:25:50 +02:00
Yuan Yao
febffe8dd1 spi: fsl_qspi: Enable Spansion S25FS-S family flashes
The flash type of LS2085AQDS QSPI is S25FS256S. It has special write
any device register command and read any device register command.
This patch enable support for those commands.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:16 -07:00
Yuan Yao
4e14741833 spi: fsl_qspi: Assign AMBA mem according CS num in dts
QSPI controller automatic enable the chipselect signal according the
dest AMBA memory address. Now we distribute the AMBA memory zone
averagely to every chipselect slave device according chipselect
numbers got from dts node.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:06 -07:00
Yuan Yao
bf9bffa978 spi: fsl_qspi: Fix issues on arm64
The address value and size value get from dts "reg" property have
type of u64 on arm64. If we assign those values to "u32" variables,
driver can't work correctly. Converting the type of those variables
to fdt_xxx_t.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:50:48 -07:00
Peng Fan
7a3eff4ce9 dm: spi: introduce dm api
Introduce dm_spi_claim_bus, dm_spi_release_bus and dm_spi_xfer
Convert spi_claim_bus, spi_release_bus and spi_xfer to use
the new API.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Peng Fan
102412c415 dm: spi: soft_spi: switch to use linux compatible string
1. Support compatible string "spi-gpio" which is used by Linux
   Linux use different bindings, so use UBOOT_COMPAT and
   LINUX_COMPAT to differentiate them.
2. Introduce SPI_MASTER_NO_RX and SPI_MASTER_NO_TX to handle
   no rx or no tx case.
3. Tested on i.MX6 UltraLite board with 74LV595 spi-gpio chip.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Peng Fan
b6d54d5273 dm: spi: soft_spi bug fix
When doing xfer, should use device->parent, but not device
When doing bit xfer, should use "!!(tmpdout & 0x80)", but not
"(tmpdout & 0x80)"

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Marek Vasut
5a824c493a mtd: cqspi: Simplify indirect read code
The indirect read code is a pile of nastiness. This patch replaces
the whole unmaintainable indirect read implementation with the one
from upcoming Linux CQSPI driver, which went through multiple rounds
of thorough review and testing. All the patch does is it plucks out
duplicate ad-hoc code distributed across the driver and replaces it
with more compact code doing exactly the same thing. There is no
speed change of the read operation.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
2016-05-06 18:41:49 +02:00
Marek Vasut
26da6353e1 mtd: cqspi: Simplify indirect write code
The indirect write code is buggy pile of nastiness which fails horribly
when the system runs fast enough to saturate the controller. The failure
results in some pages (256B) not being written to the flash. This can be
observed on systems which run with Dcache enabled and L2 cache enabled,
like the Altera SoCFPGA.

This patch replaces the whole unmaintainable indirect write implementation
with the one from upcoming Linux CQSPI driver, which went through multiple
rounds of thorough review and testing. While this makes the patch look
terrifying and violates all best-practices of software development, all
the patch does is it plucks out duplicate ad-hoc code distributed across
the driver and replaces it with more compact code doing exactly the same
thing.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
2016-05-06 18:41:49 +02:00
Stefan Roese
9fc56631a4 spi: kirkwood_spi: Add support for multiple chip-selects on MVEBU
Currently only chip-select 0 is supported by the kirkwood SPI driver.
The Armada XP / 38x SoCs also use this driver and support multiple chip
selects. This patch adds support for multiple CS on MVEBU.

The register definitions are restructured a bit with this patch. Grouping
them to the corresponding registers.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-04-06 15:38:56 +02:00
Stefan Roese
951f1b5f37 spi: kirkwood_spi.c: Add compatible match ID for Armada 375
This enables this driver for the Marvell Armada 375 SoC.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviwer-by: Jagan Teki <jteki@openedev.com>
2016-04-04 11:21:27 +02:00
Jagan Teki
41bccb8142 spi: omap3: Fix multiple definition of 'priv'
Global definition of priv seems no-sense to use it
for non-dm case and pass the pointer to functions
which are common to both dm and non-dm.

So, fix this by removing omap3_spi_slave from non-dm
and make visible to omap3_spi_priv for both dm and non-dm.

Cc: Christophe Ricard <christophe-h.ricard@st.com>
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-03-15 14:50:09 -04:00
Jagan Teki
77b8d04854 spi: omap3: Convert to driver model
After this conversion the driver will able to support both dm and non-dm
and code is more extensible like we can remove the non-dm part simply
without touching anycode if all the boards which are using this driver
become dm driven.

Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Ricard <christophe-h.ricard@st.com>
Tested-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
[Set priv->wordlen, Add Kconfig entry and file credit for dm conversion]
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
2016-03-14 22:46:28 +05:30
Jagan Teki
03661d85f0 spi: omap3: Make local functions as static
Attach static on local defined functions.

Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
2016-03-14 22:46:28 +05:30
Jagan Teki
682c172350 spi: omap3: Move headers code inside the driver
Header file have macro's and register definition and some unneeded
function proto types which becomes tunned further in future patches
and entire driver code resides in one file for more readability.

Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
[Fixes on code styles, Remove omap3_spi_txrx|write|read in header]
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
2016-03-14 22:46:16 +05:30
Lokesh Vutla
e6601df8ac dm: ti_qspi: Fix conversion of address to a pointer
TI QSPI driver directly typecasts fdt_addr_t to a pointer. This is
not strictly correct, as it gives a build warning when fdt_addr_t is u64.
So, use map_physmem for a proper typecasts.

This is inspired by commit 167efe01bc ("dm: ns16550: Use an address
instead of a pointer for the uart base")

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-03-12 19:55:42 +05:30
Christophe Ricard
674f3609aa spi: spi-uclass: Set slave wordlen with SPI_DEFAULT_WORDLEN
In some case wordlen may not be set. Use SPI_DEFAULT_WORDLEN as default.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-02-23 16:14:46 +05:30
Christophe Ricard
3963919e5b spi: omap3: Remove unused variable irqstatus in omap3_spi_txrx
Remove unused variable irqstatus in omap3_spi_txrx

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-02-23 16:14:46 +05:30
Mugunthan V N
518b0afc33 spi: ti_qspi: compile out spi_flash_copy_mmap when CONFIG_DMA is defined
When CONFIG_DMA is defined the default spi_flash_copy_mmap() can
handle dma memory copy, so compile out spi_flash_copy_mmap() from
ti_qspi driver when CONFIG_DMA config is defined.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-02-23 16:14:46 +05:30
Bin Meng
3e389d8ba6 dm: pch: Rename get_sbase op to get_spi_base
Spell out 'sbase' to 'spi_base' so that it looks clearer.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-02-05 12:47:21 +08:00
Bin Meng
6e670b5c4d spi: ich: Change PCHV_ to ICHV_
The ICH SPI controller supports two variants, one of which is ICH7
compatible and the other is ICH9 compatible. Change 'pch_version'
to 'ich_version' to better match its original name.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Simon Glass <sjg@chromium.org>
2016-02-05 12:47:20 +08:00
Bin Meng
1f9eb59d27 spi: ich: Use compatible strings to distinguish controller version
At present ich spi driver gets the controller version information via
pch, but this can be simply retrieved via spi node's compatible string.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Simon Glass <sjg@chromium.org>
2016-02-05 12:47:20 +08:00
Bin Meng
9eb4339ba4 spi: ich: Some clean up
This cleans up the ich spi driver a little bit:
- Remove struct ich_spi_slave that is not referenced anywhere
- Remove ending period in some comments
- Move struct ich_spi_platdata and struct ich_spi_priv to ich.h
- Add #ifndef _ICH_H_ .. in ich.h

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-02-05 12:47:20 +08:00
Tom Rini
cd85bec36d Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-01-27 15:05:36 -05:00
Gong Qianyu
940d2b89bf spi: fsl_qspi: Fix qspi_op_rdsr memcpy issue
In current driver, we always copy 4 bytes to the dest memory.
Actually the dest memory may be shorter than 4 bytes.
Add an argument to indicate the dest memory length.
Avoid writing memory outside of the bounds.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:28:31 -08:00
Gong Qianyu
5207014deb spi: fsl_qspi: Fix qspi_op_rdid memcpy issue
In current driver everytime we memcpy 4 bytes to the dest memory
regardless of the remaining length.
This patch adds checking the remaining length before memcpy.
If the length is shorter than 4 bytes, memcpy the actual length of data
to the dest memory.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:28:04 -08:00
Gong Qianyu
c2a4cb17b4 spi: fsl_qspi: fix compile warning for 64-bit platform
This patch fixes the following compile warning:
drivers/spi/fsl_qspi.c: In function 'fsl_qspi_probe':
drivers/spi/fsl_qspi.c:937:15:
  warning: cast to pointer from integer of different size
					 [-Wint-to-pointer-cast]
  priv->regs = (struct fsl_qspi_regs *)plat->reg_base;
               ^
Just make the cast explicit.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:27:49 -08:00
Simon Glass
f2b85ab5e6 dm: x86: spi: Convert ICH SPI driver to driver model PCI API
At present this SPI driver works by searching the PCI buses for its
peripheral. It also uses the legacy PCI API.

In addition the driver has code to determine the type of Intel PCH that is
used (version 7 or version 9). Now that we have proper PCH drivers we can
use those to obtain the information we need.

While the device tree has a node for the SPI peripheral it is not in the
right place. It should be on the PCI bus as a sub-peripheral of the LPC
device.

Update the device tree files to show the SPI controller within the PCH, so
that PCI access works as expected.

This patch includes Bin's fix-up patch from here:

   https://patchwork.ozlabs.org/patch/569478/

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-24 12:07:17 +08:00
Simon Glass
fffe25db04 spi: ich: Separate out the read/write trace from normal debugging
The trace is seldom useful for basic debugging. Allow it to be enabled
separately so that it is easier to see the more important init and error
debug messages.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-24 12:07:17 +08:00
Simon Glass
90a28470fc rockchip: spi: Remove the explicit pinctrl setting
The correct pinctrl is handled automatically so we don't need to do it in
the driver. The exception is when we want to use a different chip select
(other than 0). But this isn't used at present.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:36 -07:00
Simon Glass
e15af8e2cd rockchip: spi: Correct chip-enable code
At present there is an incorrect call to rkspi_enable_chip(). It should
be disabling the chip, not enabling it. Correct this and ensure that the
chip is disabled when releasing the bus.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:36 -07:00