Board config.mk do not need to add -DCONFIG_SYS_TEXT_BASE
to CPPFLAGS because the top level config.mk does instead.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
T1042RDB_PI is Freescale Reference Design Board supporting the T1042
QorIQ Power Architecture™ processor. T1042 is a reduced personality
of T1040 SoC without Integrated 8-port Gigabit. The board is designed
with low power features targeted for Printing Image Market.
T1042RDB_PI is similar to T1040RDB board with few differences like
it has video interface, supports T1042 personality
T1042RDB_PI board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Two on-board RGMII 10/100/1G ethernet ports.
- SERDES Connections, 8 lanes supporting:
— PCI
— SATA 2.0
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Video
- DIU supports video at up to 1280x1024x32bpp
- HDMI connector
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Device connected: EEPROM, thermal monitor, VID controller, RTC
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
- Remove duplicate doc/README.p1010rdb
- Rename README to README.P1010RDB-PA
- Add new README.P1010RDB-PB
P1010RDB-PB is a variation of previous P1010RDB-PA board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Use a default RCW of protocol 0x66.
A PBI configure file which uses CPC as 256KB SRAM. It can be used by
PBL tool on T1040 to build a pbl boot image.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
This allows to share some common code for the boards that use a corenet
base SoC.
Two different versions of the function are available in
fsl_corenet_serdes.c and fsl_corenet2_serdes.c files.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix t1040qds.c]
Acked-by: York Sun <yorksun@freescale.com>
c29xpcie REV_A board DDR ECC chip has bad impedance in hardware,
force that kind of board to be DDR ECC off when booting.
Other version board config ECC on/off by hwconfig=fsl_ddr:ecc=on
in uboot enviroment.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
- Rename old P1010RDB board as P1010RDB-PA.
- Add support for new P1010RDB-PB board.
- Some optimization.
For more details, see board/freescale/p1010rdb/README.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix conflicts in boards.cfg]
Acked-by: York Sun <yorksun@freescale.com>
Since pins multiplexing, SDHC shares signals with IFC, with this patch:
To enable SDHC in case of NOR/NAND/SPI boot
a) For temporary use case in runtime without reboot system
run 'mux sdhc' in u-boot to validate SDHC with invalidating IFC.
b) For long-term use case
set 'esdhc' in hwconfig and save it.
To enable IFC in case of SD boot
a) For temporary use case in runtime without reboot system
run 'mux ifc' in u-boot to validate IFC with invalidating SDHC.
b) For long-term use case
set 'ifc' in hwconfig and save it.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Some boards use System EEPROM with 128-bytes instead of 256-bytes.
Since we regard 256-bytes EEPROM as standard EEPROM with default
value for MAX_NUM_PORTS. For those non-256-bytes EEPROM, we can
redefine MAX_NUM_PORTS in board-specific file to override the
default MAX_NUM_PORTS.
This patch doesn't impact on previous existing boards.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
T1040QDS is a high-performance computing evaluation, development and
test platform supporting the T1040 QorIQ Power Architecture™ processor.
T1040QDS board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch
- Four 1 Gbps Ethernet controllers
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: fix conflict in boards.cfg]
Acked-by-by: York Sun <yorksun@freescale.com>
Some DDR related structures present in fsl_ddr_dimm_params.h, fsl_ddr_sdram.h, ddr_spd.h
has various parameters with embedded acronyms capitalized that trigger the CamelCase
warning in checkpatch.pl
Convert those variable names to smallcase naming convention and modify all files
which are using these structures with modified structures.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Use a default RCW of protocol 0x2A_0x98, and a PBI configure file which
uses CPC1 as 512KB SRAM, then PBL tool can be used on B4860 to build a
pbl boot image.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Default configuration has been changed, the most important one is DDR
ref_clock which is changed from 66.67MHz to 133.33MHz. so the ratio need to
change from 24x to 12x to keep the DDR frequency. There are also some
other optimise to align with default configuration.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Fix PHY addresses for QSGMII Riser Card working in
SGMII mode on board P3041/P5020/P4080/P5040/B4860.
QSGMII Riser Card can work in SGMII mode, but
having the different PHY addresses.
So the following steps should be done:
1. Confirm whether QSGMII Riser Card is used.
2. If yes, set the proper PHY address.
Generally, the function is_qsgmii_riser_card() is
for step 1, and set_sgmii_phy() for step 2.
However, there are still some special situations,
take P5040 and B4860 as examples, the PHY addresses
need to be changed when serdes protocol is changed,
so it is necessary to confirm the protocol before
setting PHY addresses.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
SGMII5/6 and SGMII7/8 are not on the same slot on P5040
according to the serdes protocol.
So it is not proper to organize SGMII5/6 and SGMII7/8
on one bus and SGMII5/6 can't work.
So a new bus SUPER_HYDRA_FM3_SGMII_MDIO is added for
SGMII5/6
Signed-off-by: Zhao Qiang <B45475@freescale.com>
DDR parameters clk_adjust were changed. This can make the DDR
run more stable. The new value were gotten by the DDR testing
tool.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
If smc911x_initialize() fails we should return the error immediately.
While at it, also check the error from cpu_eth_init().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Currently board_eth_init() always return 0, but we should propagate the error
when cpu_eth_init() fails.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently board_eth_init() always return 0, but we should propagate the error
when cpu_eth_init() fails.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If a HDMI cable is not connected, the following message is seen on boot:
CPU: Freescale i.MX6Q rev1.1 at 792 MHz
Reset cause: POR
Board: MX6-SabreSD
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
No panel detected: default to HDMI
unsupported panel HDMI
Reset the 'i' variable to fix the 'unsupported panel' message.
This follows the same idea of commit 47ac53d7ae (imx: nitrogen6x/mx6qsabrelite:
Fix bug in board_video_skip).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Since commit d9b894603 (mx6sabresd: Add LVDS splash screen support) the
following hang happens if the HDMI cable is not connected or the 'panel'
variable is not set:
U-Boot 2013.10-rc2-12978-g47ac53d-dirty (Sep 11 2013 - 15:07:38)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6-SabreSD
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
...
Provide a check to 'dev->detect' in order to prevent the hang.
Reported-by: Pardeep Kumar Singla <b45784@freescale.com>
Suggested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fix various misspellings of things like "environment", "kernel",
"default" and "volatile", and throw in a couple grammar fixes.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
mx6sabresd boards can be connected to a Hannstar XGA LVDS panel.
Add support for displaying U-boot splashscreen on it.
By default, HDMI splash is selected.
In order to use splash via LVDS, do the following in the U-boot prompt:
setenv panel Hannstar-XGA
save
and reboot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Make sure value in register r0 and r1 is preserved and passed to
the board_init_ll() and mxs_common_spl_init() where it can be
processed further. The value in r0 can be configured during the
BootStream generation to arbitary value, r1 contains pointer to
return value from CALL'd function.
This patch also clears the value in r0 before returning to BootROM
to make sure the BootROM is not confused by this value.
Finally, this patch cleans up some comments in the start.S file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
- Added section "u_boot_list" in arch/powerpc/cpu/mpc85xx/u-boot-spl.lds
- Use the function i2c_init_all instead of i2c_init
Signed-off-by: Ying Zhang <b40530@freescale.com>
There was a bug for calculating ddr_freq_mhz,
it should be divided by 1000000 rather than 0x1000000.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
When using QSGMII protocols, the first lane and third lane on each slot
need to be swapped.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Masahiro Yamada
Priyanka Jain
Shengzhou Liu
Prabhakar Kushwaha
Tom Rini
Valentin Longchamp
Po Liu
Shaohui Xie
Ying Zhang
Zhao Qiang
Wolfgang Denk
Fabio Estevam
Robert P. J. Day
Stefano Babic
Marek Vasut