arch_cpu_init() can be simpler by this refactoring.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Generally the microcode is combined into a single block only (and removed
from the device tree) when there are multiple blocks. But this is not a
requirement.
Adjust the ivybridge code to avoid assuming this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a debug() at this point to help figure out what is wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher<hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To support the BayTrail internal SIO HS UART, the internal UART clock
needs to get configured. This patch adds support for this clock
configuration which will be done, if the PCI device(s) are found.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With the change to set up pinctrl after relocation, link fails to boot. Add
a special case in the link code to handle this.
Fixes: d8906c1f (x86: Probe pinctrl driver in cpu_init_r())
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This introduces quark-specific ACPI global NVS structure, defined in
both C header file and ASL file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This introduces baytrail-specific ACPI global NVS structure, defined in
both C header file and ASL file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are quite a number of BayTrail boards that uses an external
SuperIO chipset to provide the legacy UART. For such cases, it's
better to have a Kconfig option to enable the internal UART.
So far BayleyBay and MinnowMax boards are using internal UART as
the U-Boot console, enable this on these two boards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have drivers for several more devices now, so drop the strings which are
no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is a dummy pch driver in the coreboot directory. This causes
drivers of its children fail to function due to empty ops. Remove
the whole file since it is no longer needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present pinctrl driver gets probed in ich6_gpio driver's probe
routine, which has two issues:
- Pin's PADs only gets configured when GPIO driver is probed, which
is not done by default. This leaves the board in a partially
functional state as we must initialize PADs correctly to get
perepherals fully working.
- The probe routine of pinctrl driver is called multiple times, as
normally there are multiple GPIO controllers. It should really
be called just once.
Move the call to syscon_get_by_driver_data() from ich6_gpio driver
to cpu_init_r().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
So far this is hardcoded to 2, but it should really be read
from the I/O APIC register.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently ID 2 is assgined to broadwell I/O APIC, however per
chromebook_samus.dts 2 is the core#2 LAPIC ID. Now we change
I/O APIC ID to 4 to avoid conflict.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After power-on, both LAPIC and I/O APIC appear with the same APIC ID
zero, which creates an ID conflict. When generating MP table, U-Boot
reports zero as the LAPIC ID in the processor entry, and zero as the
I/O APIC ID in the I/O APIC as well as the I/O interrupt assignment
entries. Such MP table confuses Linux kernel and finally a kernel
panic is seen during boot:
BUG: unable to handle kernel paging request at ffff9000
IP: [<c101d462>] native_io_apic_write+0x22/0x30
*pdpt = 00000000014fb001 *pde = 00000000014ff067 *pte = 0000000000000000
Oops: 0002 [#1]
Modules linked in:
Pid: 1, comm: swapper Tainted: G W 3.8.7 #3 intel galileo/galileo
EIP: 0060:[<c101d462>] EFLAGS: 00010086 CPU: 0
EIP is at native_io_apic_write+0x22/0x30
...
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present LAPIC is enabled and configured as virtual wire mode
in lapic_setup() only when CONFIG_SMP is on. This limitation is
however not necessary as for uniprocessor this is still needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Intel Quark processor core provides an integrated Local APIC but
does not support the IA32_APIC_BASE MSR. As a result, the Local
APIC is always globally enabled and the Local APIC base address
is fixed at 0xfee00000. Attempting to access the IA32_APIC_BASE
MSR causes a general protection fault.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When SeaBIOS is on, reserve configuration tables in reserve_arch().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of asking each platform to provide reserve_arch(),
supply it in arch/x86/cpu/cpu.c in a unified way.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PIRQ routing table checksum is fixed up in copy_pirq_routing_table(),
which is fine if we only write the configuration table once. But with
the SeaBIOS case, when we write the table for the second time, the
checksum will be fixed up to zero per the checksum algorithm, which
is caused by the checksum field not being zero before fix up, since
the checksum has already been calculated in the first run.
To fix this, move the checksum fixup to create_pirq_routing_table(),
so that copy_pirq_routing_table() only does what its function name
suggests: copy the table to somewhere else.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present board_final_cleanup() is called before booting a Linux
kernel. This actually needs to be done before booting anything,
like SeaBIOS, VxWorks or Windows.
Move the call to last_stage_init() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename qemu/acpi_table.c to qemu/e820.c, because ACPI stuff is moved
to qfw core, this file only contains code for installing e820 table.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Loading ACPI table from QEMU's fw_cfg interface is not x86 specific
(ARM64 may also make use of it). So move the code to common place.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make file names consistent with CONFIG_QFW and CONFIG_CMD_QFW
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds some comments about qfw register endianness for clarity.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The original implementation of qfw includes several x86 specific
operations, like directly calling outb/inb and using some inline
assembly code which prevents it being ported to other architectures.
This patch adds callback functions and moves those to arch/x86/
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch splits qfw command interface and qfw core function into two
files, and introduces a new Kconfig option (CONFIG_QFW) for qfw core.
Now when qfw command interface is enabled, it will automatically select
qfw core. This patch also makes the ACPI table generation select
CONFIG_QFW.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch is part of the qfw refactor work.
The qemu_fwcfg_free_files() function is only used in error handling in
ACPI table generation, let's not make this a core function and move it
to the right place.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
CONFIG_GENENRATE_ACPI_TABLE controls the generation of ACPI table which
uses U-Boot's built-in methods and CONFIG_QEMU_ACPI_TABLE controls whether
to load ACPI table from QEMU's fw_cfg interface.
But with commit "697ec431469ce0a4c2fc2c02d8685d907491af84 x86: qemu: Drop
our own ACPI implementation", there is only one way to support ACPI table
for QEMU targets which is the fw_cfg interface. Having two Kconfig options
for this purpose is not necessary any more, so this patch consolidates
the two.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Move the command portion of arch/x86/cpu/qemu/fw_cfg.c into
cmd/qemu_fw_cfg.c
- Move arch/x86/include/asm/fw_cfg.h to include/qemu_fw_cfg.h
- Rename ACPI table portion to arch/x86/cpu/qemu/acpi_table.c
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
FADT/MADT tables are platform specific. Generate them for BayTrail.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default SCI is disabled after power on. ACTL is the register to
enable SCI and route it to PIC/APIC. To support both ACPI in PIC
mode and APIC mode, configure SCI to use IRQ9.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reserve IRQ9 which is to be used as SCI interrupt number
for ACPI in PIC mode.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove asm/acpi.h which is never used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This started as 'ahci' and was renamed to 'disk' during code review. But it
seems that this is too generic. Now that we have a 'blk' uclass, we can use
that as the generic piece, and revert to ahci for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Our own ACPI implementation (when CONFIG_QEMU_ACPI_TABLE is not set)
does not build anymore after x86 has been fully converted to DM PCI.
Instead of trying to fix the build errors, given we now have the ACPI
support via QEMU's fw_cfg interface, which is a more reliable way to
generate correct ACPI tables than by ourselves, hence drop our own
ACPI implementation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the link script to drop this code when not needed. This is only done
for two architectures at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sometimes it is useful to jump into U-Boot directly from coreboot or UEFI
without any 16-bit init. This can help during development by allowing U-Boot
to avoid doing all the init required by the platform.
U-Boot expects its GDT to be set up correctly by its 16-bit code. If
coreboot doesn't do this (because it hasn't run the payload setup code yet)
then this won't happen.
In this case we cannot rely on the GDT settings. U-Boot will hang or crash
if these are wrong. Provide a development-only option to set up the GDT
correctly. This is just a hack so you can jump to U-Boot from any stage of
coreboot, not just at the end.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust the existing implementation to use the new common SDRAM init code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The code to call the memory reference code is common to several Intel CPUs.
Add common code for performing this init. Intel calls this 'Pre-EFI-Init'
(PEI), where EFI stands for Extensible Firmware Interface.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The SATA indexed register write functions are common to several Intel PCHs.
Move this into a common location.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Provide a way to determine the HSIO (high-speed I/O) version supported by
the Intel Management Engine (ME) implementation on the platform.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Broadwell uses a binary blob called the memory reference code (MRC) to start
up its SDRAM. This is similar to ivybridge so we can mostly use common code
for running this blob.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Broadwell requires quite a bit of power-management setup. Add code to set
this up correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
[squashed in http://patchwork.ozlabs.org/patch/598373/]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Broadwell needs a special binary blob to set up the PCH. Add code to run
this on start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Add a driver for the broadwell LPC (low-pin-count peripheral). This mostly
uses common code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Add a driver for the broadwell northbridge. This sets up the location of
several blocks of registers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Add a SATA driver for broadwell. This supports connecting an SSD and the
usual U-Boot commands to read and write data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
GPIO pins need to be set up on start-up. Add a driver to provide this,
configured from the device tree.
The binding is slightly different from the existing ICH6 binding, since that
is quite verbose. The new binding should be just as extensible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Add a driver for the broadwell low-power platform controller hub.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
This adds the broadwell architecture, with the CPU driver and some useful
header files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Each CPU needs to have its microcode loaded. Add support for this so that
all CPUs will have the same version.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable the microcode feature so that the microcode version is shown with the
'cpu detail' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
As each core starts up, record its microcode version and CPU ID so these can
be presented with the 'cpu detail' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the MRC options are private to ivybridge. Other Intel CPUs also
use these settings. Move them to a common place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some of the Intel ME code is common to several Intel CPUs. Move it into a
common location. Add a header file for report_platform.c also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[squashed in http://patchwork.ozlabs.org/patch/598372/]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This same name is used in USB. Add a prefix to distinguish it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some of the Intel CPU code is common to several Intel CPUs. Move it into a
common location along with required declarations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some of the LPC code is common to several Intel LPC devices. Move it into a
common location.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is similar to MCH in that it is used in various drivers. Add it to
the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There are several blocks of registers that are accessed from all over the
code on Intel CPUs. These don't currently have their own driver and it is
not clear whether having a driver makes sense.
An example is the Memory Controller Hub (MCH). We map it to a known location
on some Intel chips (mostly those without FSP - Firmware Support Package).
Add a new header file for these registers, and move MCH into it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This code is used on several Intel CPUs. Move it into a common location.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This cache-as-RAM (CAR) code is common to several Intel chips. Create a new
intel_common directory and move it in there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These two identifiers can be useful for drivers which need to adjust their
behaviour depending on the CPU family or stepping (revision).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Intel SIPI (start-up inter-processor interrupt) vector is the entry
point for each secondary CPU (also called an AP - applications processor).
The assembler and C code are linked, so add comments to indicate this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The timeout step is always 50us. By updating apic_wait_timeout() to print
the debug messages we can simplify the code. Also tidy up a few messages and
comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Many of the model-specific indexes are common to several Intel CPUs. Add
some more common ones, and remove them from the ivybridge-specific header
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This does not need to be modified at run-time, so make it const.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Change the parameter and return value of write_acpi_tables() to u32
to conform with other table write routines.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move asm/arch-coreboot/tables.h to asm/coreboot_tables.h so that
coreboot table definitions can be used by other x86 builds.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds basic support to Intel Cougar Canyon 2 board, a board
based on Chief River platform with an Ivy Bridge processor and
a Panther Point chipset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Wrap initialization codes with #ifndef CONFIG_HAVE_FSP #endif,
and enable the build for both FSP and non-FSP configurations.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
IvyBridge FSP package is built with a base address at 0xfff80000,
and does not use UPD data region. This adds basic FSP support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested on link (ivybridge non-FSP)
Tested-by: Simon Glass <sjg@chromium.org>
Purely by code inspection, it looks like the parameter order to memalign()
is swapped; its parameters are (align, size). 4096 is a likely desired
alignment, and a variable named size sounds like a size:-)
Fixes: 45b5a37836 ("x86: Add multi-processor init")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
There are still two places in Quark's MRC codes that use the generic
legacy PCI APIs, but as we are phasing out these legacy APIs, switch
to use Quark's own PCI config routines.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have converted all x86 codes to use DM PCI APIs,
drop those legacy ones.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Drop legacy PCI APIs usage in pci_assign_irqs() as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Use pci_[read|write]_config intead of x86_pci_[read|write]_config.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
With recent DM PCI changes to vesa_fb driver, external graphics
card does not work any more. This is because: after setting the
function disable bit, IGD and SDVO devices will disappear in the
PCI configuration space. This however creates an inconsistent state
from a driver model PCI controller point of view, as these two PCI
devices are still attached to its parent's child device list as
maintained by the driver model. Some driver model PCI APIs like
dm_pci_find_class() used in the vesa_fb driver, are referring to
the list to speed up the finding process instead of re-enumerating
the whole PCI bus, so it gets the stale cached data which is wrong.
To fix this, manually remove these two devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Once we get udevice of IGD and SDVO, we can use its udevice to
access PCI configuration space with dm_pci_write_config32().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
So far disable_igd() does not have any return value, but we may need
that in the future.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Now that we have irq router's udevice passed as a parameter, it's
time to start using the DM PCI API instead of those legacy ones.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
At present irq_router is declared as a static struct irq_router in
arch/x86/cpu/irq.c. Since it's a driver control block, it makes sense
to move it to a per driver priv. Adjust existing APIs to accept an
additional parameter of irq_router's udevice.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
There is no need to parse PCH's <reg> property as we have already
a DM PCI API dm_pci_get_bdf() that can handle this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Implement get_gpio_base op for bd82x6x, pch7 and pch9 drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Spell out 'sbase' to 'spi_base' so that it looks clearer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
pch_get_version op was only used by the ich spi controller driver,
and does not really provide a good identification of pch controller
so far, since we see plenty of Intel PCH chipsets and one differs
from another a lot, which is not simply either a PCHV_7 or PCHV_9.
Now that ich spi controller driver was updated to not get such info
from pch, the pch_get_version op is useless now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Unprotecting SPI flash is now handled in the SPI controller driver,
via a call to the PCH driver. Drop the ad-hoc version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Unprotecting SPI flash is now handled in the SPI controller driver,
via a call to the PCH driver. Drop the ad-hoc version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This patch adds the ability to load and link ACPI tables provided by QEMU.
QEMU tells guests how to load and patch ACPI tables through its fw_cfg
interface, by adding a firmware file 'etc/table-loader'. Guests are
supposed to parse this file and execute corresponding QEMU commands.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Enable ACPI IO space for piix4 (for pc board) and ich9 (for q35 board)
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Re-write the logic in qemu_fwcfg_list_firmware(), add a function
qemu_fwcfg_read_firmware_list() to handle reading firmware list.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Masahiro Yamada
Simon Glass
Stefan Roese
Tom Rini
Bin Meng
Miao Yan
Stephen Warren