Commit graph

7 commits

Author SHA1 Message Date
Nikita Kiryanov
52658fda7a compulab: eeprom: add support for defining eeprom i2c bus
Create CONFIG_SYS_I2C_EEPROM_BUS #define to tell the EEPROM
module what I2C bus the EEPROM is located at. Make cl_eeprom_read()
switch to that bus when reading EEPROM.

Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-09-09 15:32:32 +02:00
pekon gupta
434f2cfcad ARM: omap: move board specific NAND configs out from ti_armv7_common.h
This patch moves some board specific NAND configs:
- FROM: generic config file 'ti_armv7_common.h'
- TO:   individual board config files using these configs.
So that each board can independently set the value as per its design.

Following configs are affected in this patch:
  CONFIG_SYS_NAND_U_BOOT_OFFS: <refer doc/README.nand>
  CONFIG_CMD_SPL_NAND_OFS: <refer doc/README.falcon>
  CONFIG_SYS_NAND_SPL_KERNEL_OFFS: <refer doc/README.falcon>
  CONFIG_CMD_SPL_WRITE_SIZE: <refer doc/README.falcon>

This patch also updates documentation for few of above NAND configs.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-07-25 16:26:12 -04:00
pekon gupta
68128e0a86 omap3: remove remnant macros GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT
OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros
to configure GPMC controller for x7 or x8 bit device connected to its interface.
Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above
macros can be completely removed.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:07 -04:00
Mugunthan V N
9c653aad16 drivers: net: cpsw: add support to have phy address from cpsw platform data
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 09:41:53 -05:00
Ilya Ledvich
ef62df80dd cm_t335: add support for pca9555 i2c gpio extender
Add support for the 16 bits pca9555 i2c to gpio extender featured
by the SB-T335 baseboard.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-12-04 08:11:27 -05:00
Ilya Ledvich
e8ac22be6a cm_t335: add support for status LED
Add support for status LED. Use the STATUS_LED APIs for indicating a
boot progress.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-12-04 08:11:26 -05:00
Ilya Ledvich
54e7445de9 cm_t335: add cm_t335 board support
Add cm_t335 board directory, config file. Enable build.

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[trini: Adapt Makefile]
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-04 08:10:41 -05:00