Commit graph

219 commits

Author SHA1 Message Date
Michal Simek
ad5b580126 ARM: zynq: Simplify zynq configuration
Extending Kconfig for adding new platform is a lot of work
for nothing. Setting SYS_CONFIG_NAME directly in Kconfig and
remove all dependencies on TARGET_ZYNQ_* options including SPL.
As a side-effect it also remove custom init folder for ps7_init_gpl.*
files. Folder is chosen based on device-tree file.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24 13:22:50 +02:00
Michal Simek
e6a9ed04e7 ARM64: zynqmp: Add SPL support support
Support RAM and MMC boot mode in SPL also with SPL_FIT images.

In MMC boot mode two boot options are available:
1) Boot flow with ATF(EL3) and full U-Boot(EL2):
 aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
 mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000
 -d bl31.bin atf.ub
 cp spl/boot.bin <sdcard fat partition>
 cp atf.ub <sdcard fat partition>
 cp u-boot.bin <sdcard fat partition>

2) Boot flow with full U-Boot(EL3):
 cp spl/boot.bin <sdcard>
 cp u-boot*.img <sdcard>

3) emmc boot mode
 dd if=/dev/zero of=sd.img bs=1024 count=1024
 parted sd.img mktable msdos
 parted sd.img mkpart p fat32 0% 100%
 kpartx -a sd.img
 mkfs.vfat /dev/mapper/loop0p1
 mount /dev/mapper/loop0p1 /mnt/
 cp spl/boot.bin /mnt
 cp u-boot.img /mnt
 cp u-boot.bin /mnt
 cp atf.ub /mnt
 umount /dev/mapper/loop0p1
 kpartx -d sd.img
 cp sd.img /tftpboot/

 and program it via u-boot
 tftpb 10000 sd.img
 mmcinfo
 mmc write 10000 0 $filesize
 mmc rescan
 mmc part
 ls mmc 0

psu_init() function contains low level SoC setup generated for every HW
design by Xilinx design tools. xil_io.h is only supporting file to fix
all dependencies from tools. The same solution was used on Xilinx Zynq.

The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which
stays at the same location all the time.
Bootrom expects starting address to be at 0xfffc0000 that's why this
address is SPL_TEXT_BASE.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24 11:15:01 +02:00
Michal Simek
6919b4bf36 ARM64: zynqmp: Add support for reading MAC from eeprom
Add support for on board eeprom with programmed MAC for using in u-boot
to have uniq address for every board.
Most of the time uniq MAC address is on a label on the board.
If address is not programmed use these command to program it.

On zcu102:
ZynqMP> mm.b 0
00000000: 00 ? 00
00000001: a0 ? 0a
00000002: 35 ? 35
00000003: 02 ? 02
00000004: 00 ? ef
00000005: 00 ? 67
00000006: 00 ? q
i2c dev 5
i2c write 0 54 20 6
i2c md 54 20

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24 11:15:00 +02:00
Michal Simek
52be5c05a0 ARM64: zynqmp: Remove netdev.h from board file
Including netdev.h is causing compilation warning:
+ int fecmxc_register_mii_postcall(struct eth_device *dev, int
(*cb)(int));
+                                         ^
w+In file included from ../board/xilinx/zynqmp/zynqmp.c:9:0:
w+../include/netdev.h:204:41: warning: ‘struct eth_device’ declared
inside parameter list [enabled by default]
w+../include/netdev.h:204:41: warning: its scope is only this definition
or declaration, which is probably not what you want [enabled by default]

This patch removes it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:05 +02:00
Michal Simek
658b3a5639 ARM64: zynqmp: Make DDR detection code work on 32bit system
Define u64 types to be usable on 32bit system because of 64bit address
and size cells and 32bit shifts in the code.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:05 +02:00
Michal Simek
758f29d0f8 ARM: zynq: Support systems with more memory banks
This is example how to change u-boot to support more memory banks read
from DT.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:02 +02:00
Michal Simek
679b994a2b block: Add support for Ceva sata
Initial Ceva Sata init code.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-04 20:28:39 +02:00
Michal Simek
6d3ddfc473 ARM64: zynqmp: Simplify MAINTAINERS file to support more boards
Handle all Xilinx ZynqMP boards with one fragment.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:28:38 +02:00
Michal Simek
8d59d7f63b ARM64: zynqmp: Read RAM information from DT
Read information about memory from DT. This patch simplify life with
synchronization between DT and board files.

dram_init() only needs maximum RAM size below 4GB that's why please sort
banks in memory node.
dram_init_banksize() copies memory setup to bi_dram[].
This will avoid reading information from DT twice.

Memory test start/end were changed to DDR location to let memtest still
compiled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:28:38 +02:00
Michal Simek
a359eaa598 microblaze: Remove !OF_CONTROL code for timer and interrupt
OF_CONTROL is enabled by default that's why this is dead code.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:28:38 +02:00
Michal Simek
66de226f9f ARM: zynq: Fix default ps7_init_gpl.c/h for ZYBO
There is incorrect setting for USB which didn't work with origin
ps7_init_gpl.X files.
Use default setting for Digilent Zybo projects with HDMI in PL.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:28:38 +02:00
Joe Hershberger
a509a1d402 net: gem: Allow to set the MAC from an EEPROM
Provide board specific option how to read MAC address from ROM.
Do it in generic way to be reusable by differnet boards.
If this is not enough board specific functions can be created.

Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:27:54 +02:00
Michal Simek
d9f317fd0d ARM: zynq: Read memory size setting from DT
OF_CONTROL is setup by default and memory reading is done via DT. Remove
all config files with memory references.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22 16:21:02 +01:00
Ricardo Ribalda Delgado
f36919a813 ppc: xilinx-ppc440-generic: Wire LL_TEMAC driver
If the xparameters file contains a LL_TEMAC definition compile its
driver and the net commands.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:57:20 +01:00
Ricardo Ribalda Delgado
7e5281fee4 ppc: xilinx_ppc440_generic: Remove uncalled functions
board_pre_init was not called because CONFIG_BOARD_EARLY_INIT_F was not
set. Remove unused function.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:57:20 +01:00
Ricardo Ribalda Delgado
63053071b2 ppc: xilinx_ppc405_generic: Remove uncalled functions
board_pre_init was not called because CONFIG_BOARD_EARLY_INIT_F was not
set. Remove unused function.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:57:20 +01:00
Ricardo Ribalda Delgado
28e92109c7 ppc: xilinx_ppc440_generic: Remove weak attributes
Now that the specific boards have been removed there is no need to
maintain the weak functions.

Fix also CamelCase to make checkpatch happy

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:57:20 +01:00
Ricardo Ribalda Delgado
cd4695da8b ppc: xilinx_ppc405_generic: Remove weak attributes
Now that the specific boards have been removed there is no need to
maintain the weak functions.

Fix also CamelCase to make checkpatch happy

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:57:20 +01:00
Ricardo Ribalda Delgado
80cce2629b ppc: xilinx-ppc4xx: Port to DM serial
xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:57:11 +01:00
Michal Simek
5af0855670 ARM: zynq: zynqmp: Line up checkboard message
Use space instead of tab in checkboard print to aligned
it with others boards.

Reported-by: David Glessner <david.glessner@rockwellcollins.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
2016-01-27 15:55:58 +01:00
Michal Simek
cce124b8b3 ARM64: zynqmp: Remove unneeded timer_init function
Empty weak function is used instead.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:57 +01:00
Michal Simek
2d9925bce3 ARM64: zynqmp: Fix bootmode SD_MODE1
When only sdhci1 IP is enabled and SD_MODE1 bootmode is selected
U-Boot using sdboot1 variable which refers to mmc dev 1.
But this device doesn't exist because only one controller is available.

This patch fix logic around sdboot mode with using sdbootdev internal
variable.

Reported-by: Chris Kohn <ckohn@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:57 +01:00
Michal Simek
78678feeac ARM64: zynqmp: Differentiate EMMC boot mode
Show also EMMC bootmode if selected. There is difference compare to SD
bootmode. Use the same bootcommand till better boot command is created.

Reported-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:56 +01:00
Michal Simek
fb90917c46 ARM64: zynqmp: Show information about bootmode
Showing information about bootmode is very useful to make sure
that correct bootmode is selected.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:56 +01:00
Michal Simek
af813acd48 ARM64: zynqmp: Add support for SD1 boot mode
SD1 boot mode is using different bootmode values.
Add support for this mode used on DC1.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:56 +01:00
Siva Durga Prasad Paladugu
0a5bcc8c0d ARM64: zynqmp: Modify the SD and QSPI bootmode values
Modify the SD bootmode value to 0x3 as per latest
spec. Also add new boot mode QSPI 32 bit boot mode

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:56 +01:00
Michal Simek
0785dfd8a7 ARM64: zynqmp: Use the same U-Boot version with/without ATF
Remove SECURE_IOU option which is not needed. U-Boot itself can detect
which EL level it is on and based on that use do platform setup.
It also simplify usage because one Kconfig entry is gone.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:56 +01:00
Michal Simek
38c4761c23 microblaze: Fix board_init calling sequence
board_init() is in final elf file but it is not called at all.
Use board_init_late() instead and call gpio_init() from it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:53 +01:00
Michal Simek
44a3a91cb0 microblaze: Read information about RAM from DT
Do not setup ram start/size in board file. Read it from DT instead.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:53 +01:00
Michal Simek
ed982b4d41 microblaze: Remove systemace from board file
Systemace is ancient IP which is not tested. Remove it from default
configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:53 +01:00
Michal Simek
3229c869aa net: emaclite: Move emaclite to Kconfig
Add PHYLIB and MII dependencies and enable it by default for Microblaze.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:52 +01:00
Michal Simek
d538ee1b54 net: emaclite: Move driver to DM
Move driver to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:52 +01:00
Michal Simek
75cc93fad7 net: axi_emac: Move driver to DM
Move driver to DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:51 +01:00
Michal Simek
576e95b428 microblaze: Remove unused I2C macros
There is no i2c driver in the current u-boot.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:50 +01:00
Michal Simek
54e24d3332 serial: uartlite: Add uartlite to Kconfig
- Move config option out of board file.
- Remove uartlite address from config file

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-27 15:55:49 +01:00
Ricardo Ribalda Delgado
6a2c1aaae7 ppc: xilinx-ppc4xx-generic: Update xparameters.h
-Remove UART address (It is now part of the dts).
-Include dummy ns16550 clock
-Fix address to last test

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:32 +01:00
Ricardo Ribalda Delgado
bec8dd5fc0 ppc: pp440-generic: Simplify Makefile
As a result of the specific board removal, the Makefiles can be
simplified.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:32:05 +01:00
Ricardo Ribalda Delgado
6de59eb2c2 ppc: pp405-generic: Simplify Makefile
As a result of the specific board removal, the Makefiles can be
simplified.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:32:05 +01:00
Ricardo Ribalda Delgado
5b218ae106 mailaddr: Update mail address
The old mail address will stop working soon.
Update it all the files

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:32:05 +01:00
Ricardo Ribalda Delgado
9ac0efd292 ppc: xilinx-ppc440: Remove support for ml507
ml507 is just a specialized version of the xilinx-ppc440-generic

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:32:04 +01:00
Masahiro Yamada
b766476df0 microblaze: move CONFIG_SYS_TEXT_BASE to defconfig
This is how CONFIG options are defined by Kconfig.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
2016-01-20 10:19:35 -05:00
Tom Rini
5b8031ccb4 Add more SPDX-License-Identifier tags
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously.  Convert all of these to the correct SPDX-License-Identifier
tag.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 08:31:21 -05:00
Michal Simek
b5e9b9a9a1 microblaze: Do not handle watchdog and gpio in SPL
watchdog and gpio are not validated for SPL that's why do not use them.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-18 13:15:58 +01:00
Michal Simek
4632b1ea20 microblaze: Remove support for LL_TEMAC
LL_TEMAC is available at big endian MB and it is not properly tested
that's why the patch removes it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-18 13:15:58 +01:00
Nathan Rossi
f0b567bf0a ARM: zynq: Add default ps7_init_gpl.c/h for ZYBO
Add ps7_init_gpl.c/h for the ZYBO board. This instance of the ps7_init
is generated by the Vivado 2015.3 tools using the system configuration
provided by Digilent located on their website.

Update the kconfig so that the defconfig is not overrided to use the
custom init ps7_init_gpl target by default.

Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-18 13:15:57 +01:00
Michal Simek
d9ae52c8f0 zynq: sdhci: Move driver to DM
Move driver to DM

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-12-07 10:14:29 +01:00
Michal Simek
6889ca7198 net: gem: Move driver to DM
- Enable DM_ETH by default for Zynq and ZynqMP
- Remove board_eth_init code
- Change miiphy_read function to return value instead of error code
  based on DM requirement
- Do not enable EMIO DT support by default

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-12-07 10:14:22 +01:00
Michal Simek
1e370ef7e7 ARM: zynq: Remove zc70x target
Remove zc70x target which was one setting for zc702 and zc706.
Currently zc702 and zc706 are separated.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2015-11-04 14:49:53 +01:00
Siva Durga Prasad Paladugu
16fa00a711 zynqmp: usb: Add usb dwc3 driver support for zynqmp
Added usb dwc3 driver support for zynqmp
this also supports the DFU and LTHOR to download
the linux images on to RAM and cen be booted from
those linux images.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-08-19 11:27:30 +02:00
Siva Durga Prasad Paladugu
84696ff57b board: Xilinx: zynqmp: Define checkboard() function
Define checkboard() function for zynqMP

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-08-19 11:26:59 +02:00