* Added comments and a printf to warn that PCI-X won't
work at 33MHz
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
- make highboot configurations use environment at high end, too,
to avoid flash fragmentation
- always use redundand environment
- don't enable video code for modules without graphics controller
- provide useful (though different) mtdparts settings
- get rid of CONFIG_CS_AUTOCONF which was always set anyway
* Extend mkconfig tool to print more useful target name
Hint: the CPLD on the TQM5200 must be programmed with a software
version supporting the high boot option! The new TQM5200S is
already supporting this option. On the TQM5200 this option will be
supported in configurations with MPC5200 rev B processors.
To actually "high boot", set jumper X30 on the STK52xx.
Patch by Martin Krause, 12 Jul 2006
- Support for TQM5200S (short version without graphic controller)
- Support for modules with 'N' type S29GL128N Spansion flashes
(requires changes to flash layout)
- Support for MPC5200B cpu (mostly support for second SDRAM bank)
The PS/2 keyobard driver for the TQM85xx modules only supports the
internal DUART of the MPC85xx CPU. Since the MPC8560 doesn't
include a DUART, the TQM8560 modules can't be used with the PS/2
keyboard controller on the STK85xx board.
The PS/2 keyboard driver should work with the modules TQM8540,
TQM8541 and TQM8555, but it only has been tested on a TQM8540, yet.
Make sure the PS/2 controller on the STK85xx is programmed. Jumper
settings: X66 1-2, 9-10; X61 2-3
Patch by Martin Krause, 21 Jun 2006
- increase CFG_FLASH_ERASE_TOUT from 2 to 15 seconds
- use CFG_FLASH_WRITE_TOUT for programming instead of CFG_FLASH_ERASE_TOUT
- remove "Unlock Bypass" mode, because macronix flashes do not support
this mode officially
- fix flash reset command from 0x00FF to 0x00F0. 0x00FF is only specified
for Intel compatible flashes, not for AMD compatible.
Patch by Martin Krause, 15 Feb 2006
The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module
integrated in a little aluminium case.
Patch by Martin Krause, 8 Jun 2006
Some code cleanup
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.
U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).
If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Notes:
- Board-dependend code for RPXLITE and RPXCLASSIC-based boards
placed to the drivers/rpx_pmcia.c file to avoid duplication.
Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
- drivers/i82365.c has been split into two parts located at
board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
the only boards using CONFIG_82365).
- Changes were tested for clean build and *very* *few* boards.
Jon Loeliger
Matthew McClintock
Wolfgang Denk
Bartlomiej Sieka
John Traill
Stefan Roese
Haiying Wang
Jin Zhengxiong
Markus Klotzbuecher
Marian Balakowicz