Commit graph

47 commits

Author SHA1 Message Date
Stephan Linz
d1d37b5cab microblaze: Wire up OF support for emaclite
- expand the condition with CONFIG_OF_CONTROL

Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-06 13:32:30 +02:00
Michal Simek
9d24274509 microblaze: Add SPL support
Add support for U-BOOT SPL. NOR and RAM mode are supported.
There are 3 images in NOR flash. u-boot.img, dtb and kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-04 16:39:50 +01:00
Michal Simek
22ff7f4d19 microblaze: Enable buffer write for NOR flashes
It speeds up writing a lot.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-04 16:39:37 +01:00
Rob Herring
f232950f82 config: remove platform CONFIG_SYS_HZ definition part 2/2
Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:06:16 -05:00
Stephen Warren
6697d55862 xilinx: move microblaze-generic .dts to standard location
Aside from microblaze, all other SoCs/boards/vendors store their DT files
in board/$vendor/dts/$soc-$board.dts. Move microblaze-generic.dts to this
location for consistency.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <monstr@monstr.eu>
2013-08-02 18:29:32 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Michal Simek
4e779ad2e5 gpio: Add support for microblaze xilinx GPIO
Microblaze uses gpio which is connected to the system reset.
Currently gpio subsystem wasn't used for it.

Add gpio driver and change Microblaze reset logic to be done
via gpio subsystem.

There are various configurations which Microblaze can have
that's why gpio_alloc/gpio_alloc_dual(for dual channel)
function has been introduced and gpio can be allocated
dynamically.

Adding several gpios IP is also possible and supported.

For listing gpio configuration please use "gpio status" command

This patch also remove one compilation warning:
microblaze-generic.c: In function 'do_reset':
microblaze-generic.c:38:47: warning: operation on '*1073741824u'
 may be undefined [-Wsequence-point]

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-05-09 11:20:08 +02:00
Michal Simek
0f21f98dd4 watchdog: Add support for Xilinx Microblaze watchdog
Watchdog can be used on Microblaze, PPC and Zynq hw designs.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:22:43 +02:00
Michal Simek
783764521e microblaze: Enable netconsole
Setup environment and enable netconsole.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:22:39 +02:00
Michal Simek
14d315b8b3 microblaze: Remove FSL support from generic board
This code was targetting one specific Microblaze platform
configuration which is obsolete and fsl bus isn't used
in this way.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-02-04 12:09:50 +01:00
Michal Simek
5811830fae microblaze: Flush caches before enabling them
Flushing caches is necessary because of soft reset
which doesn't clear caches.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Reviewed-by: Marek Vasut <marex@denx.de>
2012-11-07 17:11:14 +01:00
Michal Simek
bcbb046bd5 microblaze: timer: Prepare for device-tree initialization
Fix CONFIG_SYS_HZ usage in board config.

Do not use hardcoded value. Use CONFIG_SYS_HZ instead.
Separate static configuration to single block.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-09-11 09:24:58 +02:00
Stephan Linz
bcec8f49d1 microblaze: Wire up SPI driver
Depending on XILINX_SPI_FLASH_BASEADDR enable SPI flash
and environment in SPI flash.

Expected values from xparameters.h are:
    - XILINX_SPI_FLASH_BASEADDR
    - XILINX_SPI_FLASH_MAX_FREQ
    - XILINX_SPI_FLASH_CS

Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Michal Simek <monstr@monstr.eu>
2012-07-31 07:16:26 +02:00
Michal Simek
575a3d21f6 microblaze: intc: Clear interrupt code
Clear and prepare for device-tree driven configuration.
Remove CONFIG_SYS_INTC_0 definition
Use dynamic allocation instead of static.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Simon Glass <sjg@chromium.org>
2012-07-10 11:54:06 +02:00
Stephan Linz
920c358781 microblaze: Wire up dts configuration
- enable OF control and embedded OF
    - set default device tree file name to 'microblaze'
    - add CPP to dtc proxy: board/xilinx/dts/microblaze.dts
    - add an empty but processable dts for microblaze-generic

Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-07-10 10:01:29 +02:00
Stephan Linz
2cce2d3231 microblaze: Add missing undefs for UBI and UBIFS
In the case of missing flash usage disaple (undef)
all the UBI support in the same way as for JFFS2.

Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-07-09 10:44:26 +02:00
Stephan Linz
8f371b1850 microblaze: Expand and correct configuration comments
- fix CONFIG_SYS_MALLOC_BASE from 0x11FB_F000 to 0x13EF_F000
  - add new size calculation for CONFIG_SYS_MONITOR_LEN
    and CONFIG_SYS_MALLOC_LEN derived from SIZE
  - change CONFIG_SYS_MONITOR_BASE and CONFIG_SYS_MALLOC_BASE
    calculation to a symbolic equation with the corresponding
    _LEN definitions
  - add a "CFI flash memory layout - Example" comment

Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-07-09 10:44:26 +02:00
Stephan Linz
7cfb13a7f4 microblaze: Enable ubi support
Increase malloc area for UBI to >= 512k -- foreseeing of UBIFS
set to 768k. To save memory in flash (CONFIG_SYS_MONITOR_LEN)
the UBIFS is disabled by default.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-06-27 10:18:44 +02:00
Stephan Linz
1fe7e8fa48 microblaze: Avoid compile error on systems without cfi flash
Use XILINX_FLASH_START to set/unset FLASH and RAMENV.

Error:
board.c: In function 'board_init':
board.c:134: error: 'XILINX_FLASH_START' undeclared (first use in this function)
board.c:134: error: (Each undeclared identifier is reported only once
board.c:134: error: for each function it appears in.)

Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-06-27 10:18:20 +02:00
Stephan Linz
2629d63efc microblaze: Remove wrong define CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_PROTECTION is defined twice. The second one
is outside the flash configuration context and we can remove
it safely.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-06-27 10:17:46 +02:00
Tom Rini
219f4788d3 hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-06-20 20:36:51 +02:00
Stephan Linz
8422a35e9b microblaze: Enable several ethernet driver compilation
U-Boot's multipple network supports enables to use
several ethernet drivers but microblaze-generic
platform config file select only one driver.

Reported-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-04-04 09:36:35 -05:00
Stephan Linz
f5e5e1ff0a microblaze: Enable phylib and mii support
Enable phylib and mii support for AXI EMAC
ethernet drivers on Microblaze systems.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-03-27 13:58:19 +02:00
Stephan Linz
4eb29cf043 microblaze: Enable TFTP put command
Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-02-23 12:17:08 +01:00
Stephan Linz
1de55ef105 microblaze: usable uart16550 for big endian systems
As a result of the commit 6833260 the uart16550 driver
is broken for Microblaze big endian systems, because of
the missing 3 byte offset. Other than as described, not
all U-Boot BSP will treat properly the 3 byte offset.

This why prefer to mask out the 3 byte offset in general
and setup correct _REG_SIZE value depending on edianess.

Signed-off-by: Stephan Linz <linz@li-pro.net>
Tested-by: Michal Simek <monstr@monstr.eu>
2011-11-27 15:49:48 +01:00
Michal Simek
e634138e73 microblaze: Wire up axi_ethernet driver initialization
Initialize axi_ethernet driver.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-24 07:50:21 +02:00
Mike Frysinger
31a4f1e5b6 board configs: drop NET_MULTI references
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00
Michal Simek
37e892d93a microblaze: Enable FDT/FIT support
Enable FDT and FIT support.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-03 08:01:56 +02:00
Michal Simek
68332608bc microblaze: Remove address offset for uart16550
U-Boot BSP handle 0x3 offset for big endian systems.
Little endian Microblaze systems don't use any offset.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-03 08:01:56 +02:00
Michal Simek
1252df0659 microblaze: Do not select NFS for platforms without ethernet
Undefined network functionality for systems without ethernet
and disable NFS support.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-03 08:01:56 +02:00
Michal Simek
1020286ef4 microblaze: Fix bd_info pointer
Patch "Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value"
(sha1: 25ddd1fb0a)
introduce GENERATED_GBL_DATA_SIZE which is sizeof aligned gd_t
(currently 0x40).
Microblaze configs used 0x40(128) because this place also contained
board info structure which lies on the top of ram.

U-Boot is placed to the top of the ram (for example 0xd7ffffff)
and bd structure was moved out of ram.

This patch is fixing this scheme with GENERATED_BD_INFO_SIZE
which swap global data and board info structures.

For example:
Current: gd 0xd7ffffc0, bd 0xd8000000
Fixed:   gd 0xd7ffffc0, bd 0xd7ffff90

Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-01-10 08:52:32 +01:00
Wolfgang Denk
25ddd1fb0a Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:05:30 +02:00
Wolfgang Denk
14d0a02a16 Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:07:10 +02:00
Michal Simek
d69f8f41af microblaze: Add support for NET_MULTI api
Microblaze hasn't supported NET_MULTI support.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2010-10-12 16:51:34 +10:00
Michal Simek
4aecfb1602 microblaze: Fix microblaze-generic config file
1. Fix preprocessor statements
2. Clean coding style

Signed-off-by: Michal Simek <monstr@monstr.eu>
2010-10-12 16:44:21 +10:00
Stephan Linz
c82a541d47 microblaze: generic: rename MTD partition set to 'flash-0'
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2010-10-12 16:44:21 +10:00
Stephan Linz
3faf987de5 microblaze: generic: adding DHCP support
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2010-10-12 16:44:21 +10:00
Graeme Smecher
8fe7b29f98 microblaze: Stop stack clobbering in microblaze-generic.
A typo caused the stack and malloc regions to overlap, which prevented
mem_malloc_init() from returning. This commit makes the memory layout match
the example described in include/configs/microblaze-generic.h

Signed-off-by: Graeme Smecher <graeme.smecher@mail.mcgill.ca>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-12-08 08:51:42 +01:00
Michal Simek
0900bee9ab microblaze: Enable hush parser
With Hush parser is possible to change command line in dtb

Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-09-14 14:40:04 +02:00
Michal Simek
3ceba1d45d net: Remove old Xilinx Emac driver
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-09-14 14:40:03 +02:00
Michal Simek
2fddd44464 microblaze: Short size of global data and fix malloc size
If is full malloc area global, data are rewrite because
there was bad size of malloc area.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-09-14 14:40:03 +02:00
Stefan Roese
942556a92a mtd: MTD related config header changes (mtdparts command)
By changing the cmd_mtdparts to only use the MTD infrastructure and
not the direct interface to the CFI NOR FLASH driver we now need
to add the MTD infrastructure to all boards using those mtdparts
commands. This patch adds those components:

CONFIG_MTD_DEVICE (for all FLASH types)

plus

CONFIG_FLASH_CFI_MTD (for NOR FLASH)

To all board maintainers: Please test this on your platforms and
report any problems/issues found. Thanks.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ron Madrid <info@sheldoninst.com>
Cc: Georg Schardt <schardt@team-ctech.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Martin Krause <martin.krause@tqs.de>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Ricardo Ribalda <ricardo.ribalda@uam.es>
2009-06-12 20:45:47 +02:00
Stefan Roese
68d7d65100 Separate mtdparts command from jffs2
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-03-20 22:39:14 +01:00
Mike Frysinger
bdab39d358 rename CONFIG_CMD_ENV to CONFIG_CMD_SAVEENV
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment.  So, let's make sure the define is named accordingly.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-18 00:47:43 +01:00
Michal Simek
e9b737deb2 microblaze: Add cache flush 2009-01-23 10:39:59 +01:00
Michal Simek
330e55459b microblaze: Change microblaze-generic config file
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-01-23 10:39:59 +01:00
Michal Simek
52a822ed9c microblaze: Rename ml401 to microblaze-generic
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-01-23 10:39:56 +01:00
Renamed from include/configs/ml401.h (Browse further)