Commit graph

1399 commits

Author SHA1 Message Date
Robert P. J. Day
25bab53ab2 Remove unneeded remnants of bcopy().
Since bcopy() is no longer used, delete all remaining references to
it.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2016-06-06 13:39:18 -04:00
mario.six@gdsys.cc
07d31f8f98 dm: gpio: Add driver for MPC85XX GPIO controller
This patch adds a driver for the built-in GPIO controller of the MPC85XX
SoC (probably supporting other PowerQUICC III SoCs as well).

Each GPIO bank is identified by its own entry in the device tree, i.e.

gpio-controller@fc00 {
      #gpio-cells = <2>;
      compatible = "fsl,pq3-gpio";
      reg = <0xfc00 0x100>
}

By default, each bank is assumed to have 32 GPIOs, but the ngpios
setting is honored, so the number of GPIOs for each bank in configurable
to match the actual GPIO count of the SoC (e.g. the 32/32/23 banks of
the P1022 SoC).

The usual functions of GPIO drivers (setting input/output mode and output
value setting) are supported.

The driver has been tested on MPC85XX, but it is likely that other
PowerQUICC III devices will work as well.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 22:13:24 -07:00
Robert P. J. Day
b7707b043e arch/powerpc: Simplify some calculations using ARRAY_SIZE() macro.
Replace a number of array length calculations with the ARRAY_SIZE()
macro, for clarity.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 22:13:12 -07:00
Robert P. J. Day
7ffe3cd62e Delete tests of CONFIG_OF_LIBFDT when testing CONFIG_OF_BOARD_SETUP
Since CONFIG_OF_BOARD_SETUP depends on CONFIG_OF_LIBFDT:

  config OF_BOARD_SETUP
          bool "Set up board-specific details in device tree before boot"
          depends on OF_LIBFDT
          ...

remove superfluous tests of CONFIG_OF_LIBFDT when testing for
CONFIG_OF_BOARD_SETUP.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[trini: Typo fix: s/ifdefi/ifdef/]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:16 -04:00
Simon Glass
14c67ebaef powerpc: Drop unused code related to generic board
Since generic board init is enabled, this is not used. Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-05-27 15:39:54 -04:00
Tom Rini
826d06dbdd Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2016-05-25 07:19:31 -04:00
Tom Rini
fc15b9beed Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-05-24 13:42:03 -04:00
Aneesh Bansal
82eda68444 powerpc/mpc85xx: set L2PE in L2CSR0 before enabling L2 cache
While enabling L2 cache, the value of L2PE (L2 cache parity/ECC
error checking enable) must not be changed while the L2 cache is
enabled.
So, L2PE must be set before enabling L2 cache.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-24 10:31:21 -07:00
York Sun
cb1629f91a powerpc: Disable flush or invalidate dcache by range for some SoCs
Commit ac337168a unified functions to flush and invalidate dcache by
range. These two functions were no-op for SoCs other than 4xx and
MPC86xx. Adding these functions seemed to be correct but introduced
issues when the dcache is flushed. While the root cause is under
investigation, disable these functions for affected SoCs so various
drivers can work.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-05-19 10:47:11 -07:00
Alex Porosanu
76394c9c91 crypto/fsl: add support for multiple SEC engines initialization
For SoCs that contain multiple SEC engines, each of them needs
to be initialized (by means of initializing among others the
random number generator).

Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:46 -07:00
Alex Porosanu
404bf4547e arch/arm, arch/powerpc: add # of SEC engines on the SOC
Some SOCs, specifically the ones in the C29x familiy can have
multiple security engines. This patch adds a system configuration
define which indicates the maximum number of SEC engines that
can be found on a SoC.

Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:46 -07:00
mario.six@gdsys.cc
dbc82ce31b dm: fsl_i2c: Enable DM for FSL I2C
Signed-off-by: Mario Six <mario.six@gdsys.cc>
2016-05-17 08:28:55 +02:00
mario.six@gdsys.cc
ec2c81c5d4 dm: fsl_i2c: Rename I2C register structure
Signed-off-by: Mario Six <mario.six@gdsys.cc>
2016-05-17 08:28:52 +02:00
Robert P. J. Day
1cc0a9f496 Fix various typos, scattered over the code.
Spelling corrections for (among other things):

* environment
* override
* variable
* ftd (should be "fdt", for flattened device tree)
* embedded
* FTDI
* emulation
* controller
2016-05-05 21:39:26 -04:00
Andreas Bießmann
09c2b8f3e3 Change my mailaddress
I'll switch my mails to my own server, so drop all gmail references.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-05-02 18:37:09 -04:00
mario.six@gdsys.cc
5068946120 powerpc: mpc85xx: Enable pre-relocation malloc for MPC85xx
To enable DM on MPC85xx, we need pre-relocation malloc, which is
implemented in this patch.

We also make sure that the IVORs are always 4-aligned on e500 to prevent
alignment exceptions caused by code changes in start.S.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Cc: York Sun <york.sun@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-04-08 15:42:10 -07:00
Mateusz Kulikowski
e162c6b1a7 usb: Rename ehci-fsl.h to ehci-ci.h
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.

This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:10 -04:00
Vagrant Cascadian
a6f70a3d14 Fix spelling of "transferred".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-22 12:16:16 -04:00
Simon Glass
73223f0e1b Kconfig: Move CONFIG_FIT and related options to Kconfig
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.

Move these options to Kconfig and tidy up board configuration:

   CONFIG_FIT
   CONFIG_OF_BOARD_SETUP
   CONFIG_OF_SYSTEM_SETUP
   CONFIG_FIT_SIGNATURE
   CONFIG_FIT_BEST_MATCH
   CONFIG_FIT_VERBOSE
   CONFIG_OF_STDOUT_VIA_ALIAS
   CONFIG_RSA

Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.

Note: Masahiro's moveconfig.py script is amazing.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:07 -04:00
Simon Glass
9e971632cd freescale: Remove CONFIG_DM from header files
Kconfig options must defined in the defconfig files. Since RSA_SOFTWARE_EXP
relies on CONFIG_DM, unless it is set in kconfig we cannot enable RSA.
Remove the hacks which enable CONFIG_DM in header files and update the
defconfig.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-03-14 14:21:27 -04:00
Qianyu Gong
075affb1ac fm: fdt: Move fman ucode fixup to driver code
Not only powerpc/mpc85xx but also Freescale Layerscape platforms will
use fdt_fixup_fman_firmware() to insert Fman ucode blob into the device
tree. So move the function to Fman driver code.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:13 -08:00
Qianyu Gong
2459afb1a7 qe: move drivers/qe/qe.h to include/fsl_qe.h
As the QE firmware struct is shared with Fman, move the header file
out of drivers/qe/.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:51:13 -08:00
Aneesh Bansal
f698e9f39a powerpc/SECURE_BOOT: Add PAMU driver
PAMU driver basic support for usage in Secure Boot.
In secure boot PAMU is not in bypass mode. Hence to use
any peripheral (SEC Job ring in our case), PAMU has to be
configured.

The patch reverts commit 7cad2e38d6.

The Header file pamu.h and few functions in driver have been derived
from Freescale Libos.

Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:40:55 -08:00
David Müller (ELSOFT AG)
928f605455 Remove unused CONFIG_MODEM_SUPPORT option and associated dead code.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
2016-02-08 10:22:44 -05:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Tom Rini
cd85bec36d Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-01-27 15:05:36 -05:00
Aneesh Bansal
d0a6d7ce55 secure_boot: enable chain of trust for PowerPC platforms
Chain of Trust is enabled for PowerPC platforms for Secure Boot.
CONFIG_BOARD_LATE_INIT is defined.
In board_late_init(), fsl_setenv_chain_of_trust() is called which
will perform the following:
- If boot mode is non-secure, return (No Change)
- If boot mode is secure, set the following environmet variables:
   bootdelay = 0 (To disable Boot Prompt)
   bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script)

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:12:56 -08:00
Aneesh Bansal
0a6b2714ad secure_boot: create function to determine boot mode
A function is created to detrmine if the boot mode is secure
or non-secure for differnt SoC's.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:12:42 -08:00
Aneesh Bansal
bdc22074c5 secure_boot: split the secure boot functionality in two parts
There are two phases in Secure Boot
1. ISBC: In BootROM, validate the BootLoader (U-Boot).
2. ESBC: In U-Boot, continuing the Chain of Trust by
         validating and booting LINUX.

For ESBC phase, there is no difference in SoC's based on ARM or
PowerPC cores.

But the exit conditions after ISBC phase i.e. entry conditions for
U-Boot are different for ARM and PowerPC.
PowerPC:

If Secure Boot is executed, a separate U-Boot target is required
which must be compiled with a diffrent Text Base as compared to
Non-Secure Boot. There are some LAW and TLB settings which are
required specifically for Secure Boot scenario.

ARM:
ARM based SoC's have a fixed memory map and exit conditions from
BootROM are same irrespective of boot mode (Secure or Non-Secure).

Thus the current Secure Boot functionlity has been split into
two parts:
CONFIG_CHAIN_OF_TRUST
This will have the following functionality as part of U-Boot:
1. Enable commands like esbc_validate, esbc_halt
2. Change the environment settings based on bootmode, determined
   at run time:
     - If bootmode is non-secure, no change
     - If bootmode is secure, set the following:
         - bootdelay = 0 (Don't give boot prompt)
         - bootcmd = Validate and execute the bootscript.

CONFIG_SECURE_BOOT
This is defined only for creating a different compile time target
for secure boot.

Traditionally, both these functionalities were defined under
CONFIG_SECURE_BOOT. This patch is aimed at removing the requirement
for a separate Secure Boot target for ARM based SoC's.
CONFIG_CHAIN_OF_TRUST will be defined and boot mode will be
determine at run time.

Another Security Requirement for running CHAIN_OF_TRUST is that
U-Boot environemnt must not be picked from flash/external memory.
This cannot be done based on bootmode at run time in current U-Boot
architecture. Once this dependency is resolved, no separate
SECURE_BOOT target will be required for ARM based SoC's.

Currently, the only code under CONFIG_SECURE_BOOT for ARM SoC's is
defining CONFIG_ENV_IS_NOWHERE

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:12:32 -08:00
Aneesh Bansal
74eecd820f secure_boot: include/configs: move definition of CONFIG_CMD_BLOB
CONFIG_CMD_BLOB must be defined in case of Secure Boot. It was
earlier defined in all config files. The definition has been
moved to a common file which is included by all configs.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:12:26 -08:00
Ricardo Ribalda Delgado
80cce2629b ppc: xilinx-ppc4xx: Port to DM serial
xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:57:11 +01:00
Ricardo Ribalda Delgado
5e68f17e24 ppc: dts: Add device tree for xilix-ppc4xx-generic
Add device tree example file for xilinx-ppc440-generic and
xilinx-ppc405-generic

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:43:01 +01:00
Ricardo Ribalda Delgado
5b218ae106 mailaddr: Update mail address
The old mail address will stop working soon.
Update it all the files

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:32:05 +01:00
Ricardo Ribalda Delgado
583aefb89c xilinx-ppc440: Remove support for v5fx30teval
It is just a specialized version of xilinx-ppc440

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:32:04 +01:00
Ricardo Ribalda Delgado
70c29dcdbc ppc: xilinx-ppc405: Remove support for fx12mm
It is just a specialized version of the xilinx-ppc405

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:32:04 +01:00
Ricardo Ribalda Delgado
9ac0efd292 ppc: xilinx-ppc440: Remove support for ml507
ml507 is just a specialized version of the xilinx-ppc440-generic

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:32:04 +01:00
Tom Rini
d82477748d Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2016-01-25 16:45:00 -05:00
Ashish kumar
43381474ff arch/powperpc: Fix start_align due to use of __ffs64() instead ffs64()
Incorrect DDR law was created in case of B4860qds after commit
2d2f490d. Return value of ffs64() differs from __ffs64(), eg.
    ffs64(0x80000000) = 0x20
    __ffs64(0x80000000) = 0x1f
As a result of this change, callers need to adjust the expected
return value by removing -1.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 12:30:31 -08:00
Prabhakar Kushwaha
2c0d69713c powerpc: mpc85xx: Move set_liodns, setup_portals to common boot seq
Users migrating Freescale's PowerPC SoC U-Boot code to their custom
board, often overlook the need to execute set_liodns() and
setup_portals() being called by platform files.

So Move set_liodns() and setup_portals() to common u-boot boot
sequence

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 12:13:31 -08:00
Shengzhou Liu
a994b3deb0 driver/ddr/fsl: Add workaround for A009663
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.

When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:15 -08:00
Tom Rini
0080931abf serial: Remove serial_putc_raw_dev
clang-3.8 reports that serial_putc_raw_dev in serial_ns16550.c is
unused.  Further investigation shows that we have 3 places that
implement this function and no callers, remove.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-25 10:39:45 -05:00
Tom Rini
6e2f153895 arm, powerpc: Update cc-version tests to check for cc-name as well
For compatibility clang will report some gcc version.  However since we
are checking gcc versions in order to then fail to build, we should
limit these tests only to when we are using gcc and not clang.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-25 10:39:44 -05:00
Tom Rini
5b8031ccb4 Add more SPDX-License-Identifier tags
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously.  Convert all of these to the correct SPDX-License-Identifier
tag.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 08:31:21 -05:00
Ben Whitten
192bc6948b Fix GCC format-security errors and convert sprintfs.
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.

Simple uses of sprintf are also converted to use strcpy.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-14 22:11:34 -05:00
Albert ARIBAUD
ecc306639e Fix board init code to respect the C runtime environment
board_init_f_mem() alters the C runtime environment's
stack it is actually already using. This is not a valid
behaviour within a C runtime environment.

Split board_init_f_mem into C functions which do not alter
their own stack and always behave properly with respect to
their C runtime environment.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-13 21:05:17 -05:00
Robert P. J. Day
d7b4ca2b6f powerpc: Various typo fixes under arch/powerpc/cpu/mpc83xx
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2016-01-08 10:15:43 -05:00
Heiko Schocher
6a655d8e34 powerpc, mpc5xxx: fix missing bootflag init
since:
commit: f05ad9ba "Add a way to skip relocation"

tqm5200s board fails to boot. Reason is that
board_init_f has a function parameter bootflag,
which is not setup in
in arch/powerpc/cpu/mpc5xxx/start.S _start

So board_init_f gets a undefined bootflag,
currently the gd pointer address. Unfortunately
this address sets the GD_FLG_SKIP_RELOC bit,
so u-boot code gets not relocated and u-boot
does not boot ...

Init bootflag with 0, and tqm5200 boots fine again.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <yorksun@freescale.com>
2016-01-05 08:33:44 -08:00
Tom Rini
1a33892164 fsl_*_serdes.c: Modify memset call in serdes_init
GCC 5.x does not like sizeof(array_variable) and errors out.  Change these
calls to be instead sizeof(u8) (as that's what serdes_prtcl_map is) *
SERDES_PRCTL_COUNT (the number of array elements).

Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:29 -08:00
Shengzhou Liu
a46b1852de fsl/ddr: updated ddr errata-A008378 for arm and power SoCs
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0,
T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on
LS102x Rev2.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:28 -08:00
Shengzhou Liu
a07bdad749 fsl/errata: move fsl_errata.h to common directory
move arch/powerpc/include/asm/fsl_errata.h to include/fsl_errata.h
to make it public for both ARM and POWER SoCs.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix soc.h path in fsl_errata.h]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-13 18:27:28 -08:00