The current implementation for baudrate calculation is incorrect.
This part from the formula:
"2 ^ (n + 1)" is not equivalent to (1 << n) but to (2 << n)!
This patch fixes this and moves this calculation to a function instead of using a macro.
This new function is taken from the Linux kernel.
This was detected and tested on the Marvell Armada A38x DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Panasonic's System LSI products, UniPhier SoC family, have been
transferred to Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Make this option available in Kconfig and clean up the board that uses it.
Note there is also an entry in exynos5-common.h but this affects multiple
boards and should be dropped as part of the Samsung I2C migration to
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Expand the help messages for each driver. Add missing Kconfig for I2C,
SPI flash and thermal.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Make the driver model I2C API available always, even if driver model
is not enabled. This allows for a 'soft' switch-over, where drivers can
use the new structures in code which is compiled but not yet used. This
makes migration easier in some cases.
Fix up the existing drivers which define their own 'struct i2c_msg'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
As with i2c_read() and i2c_write(), add a dm_ prefix to the driver model
versions of these functions to avoid conflicts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
If no device is connected to I2C bus, the i2c probe command
can take a lot of time for probe each address. This commit
reduces the busy timeout to 10ms for standard and high speed
modes. This doesn't break the transmission an also allow for
properly probe the devices.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Changes v3:
- new commit, after split the next one
Tested-by: Simon Glass <sjg@chromium.org>
These functions are useful in case the board calls them. Also fix a missing
parameter caused by applying the wrong patch (actually I failed to send v2
and applied v1 by mistake).
Signed-off-by: Simon Glass <sjg@chromium.org>
Since U-Boot can support different offset lengths (0-4 bytes), add a device
tree property to specify this. This avoids hard-coding it in the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit adjusts the s3c24x0 driver to new i2c api
based on driver-model. The driver supports standard
and high-speed i2c as previous.
Tested on Trats2, Odroid U3, Arndale, Odroid XU3
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch fixes build error for CONFIG_DM_I2C_COMPAT.
In i2c_get_chip_for_busnum() call, one of argument was missed,
which was offset_len. Now it is set to 'alen' as previous.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
At present we go through various contortions to store the I2C's chip
address in its private data. This only exists when the chip is active so
must be set up when it is probed. Until the device is probed we don't
actually record what address it will appear on.
However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the address when the child is bound,
and avoid the messy contortions.
Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
At present we try to use the 'reg' property and device tree aliases to give
devices a sequence number. The 'reg' property is often actually a memory
address, so the sequence numbers thus-obtained are not useful. It would be
better if the devices were just sequentially numbered in that case. In fact
neither I2C nor SPI use this feature, so drop it.
Some devices need us to look up an alias to number them within the uclass.
Add a flag to control this, so it is not done unless it is needed.
Adjust the tests to test this new behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Rather than assuming that the chip offset length is 1, allow it to be
provided. This allows chips that don't use the default offset length to
be used (at present they are only supported by the command line 'i2c'
command which sets the offset length explicitly).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
For boards which use multiple I2C devices, or for SOCs which support
multiple boards, we might want to convert these to driver model at different
times. At present this is difficult because we need to either use
CONFIG_DM_I2C for a board or not.
Add a compatibility layer which implements the old API, thus allowing a
board to move to driver model for I2C without requiring that everything it
uses is moved in the same commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a dm_ prefix to driver model I2C functions so that we can keep the old
ones around.
This is a little unfortunate, but on reflection it is too difficult to
change the API. We can undo this rename when most boards and drivers are
converted to use driver model for I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit adds on-chip I2C driver used on newer SoCs of Panasonic
UniPhier platform.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
This commit adds on-chip I2C driver used on some old Panasonic
UniPhier SoCs.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
We should not hardcode array size of i2c_data to 3. To CONFIG_FSL_LSCH3,
there are 4 i2c interface, but not 3. So the size of i2c_data array should
be calculated using "ARRAY_SIZE(i2c_bases)".
To avoid compile error, move i2c_bases before sram_data structure which
contains i2c_data array.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:
- CONFIG_SYS_I2C_INIT_BOARD
- CONFIG_I2C_MULTI_BUS
- CONFIG_SYS_MAX_I2C_BUS
- CONFIG_SYS_I2C_SPEED
- CONFIG_SYS_I2C
This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1
It has not been tested on Tegra 114 as I don't have that board.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver includes some test features such as only supporting certain
bus speeds. It passes its I2C traffic through to an emulator.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In order to test I2C we need some sort of emulation interface. Add hooks
to allow a driver to emulate an I2C device for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The uclass implements the same operations as the current I2C framework but
makes some changes to make it fit driver model better:
- Remove the chip address from API calls
- Remove the address length from API calls
- Remove concept of 'current' I2C bus
- Drop all existing init functions
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Due to an uninitialised variable, when muxes were deselected, any value
could be written to the mux control register. On the PCA9548, this could
result in multiple channels being selected, thus enabling multiple
pull-up resistors, and much bus capacitance.
The fix is simply to initialise the written value to zero.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
In case of repeated START condition, the restart has to be kicked
before clear status (MSR register). If it is kicked after clear status,
R-Car I2C may transfer data (TXD register) or receive data (RXD register)
instead of transferring slave address (MAR register).
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Some slow I2C devices like Power Monitor(ZM7304) at times
do not work well with low timeout value, so I2C bus get stuck
during read cycle with this device, changing it to 100ms from
10ms works fine
A lot of other i2c drivers like mxc and i2c drivers of BOOTROM
also use relax timeouts to give sufficient ticks to work well
with slower devices
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
ppc4xx i2c master gets stuck on errors while repeated start is
active. Can be easily reproduced by "i2c md" on an unpopulated
i2c address. There is not stop condition given, scl remains
pulled low.
The only way out seems to be doing a stop manually and then a
soft reset.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Debugging some i2c trouble I saw on my scope that repeated
start is not working properply. The 4xx even held clock pulled down
after transfers. Having a look in the driver I realized
that IIC_CNTL_RPST is set on that part of the transfer that should
begin with a repeated start. But repeated start is about not sending a
stop condition, so IIC_CNTL_RPST has to be set on the last transfer
before the repeated start happens.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
In preparation for the SoCFPGA support of the designware I2C driver,
convert this driver to the common CONFIG_SYS_I2C framework.
This patch converts all users of this driver, this is:
- ST spearxxx boards
- AXS101 (ARC700 platform)
I couldn't test this patch on those boards. Only compile tested for all
spear boards. And tested on SoCFPGA.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
This patch permeates the struct i2c_adapter throughout the driver,
so that it can be used to determine which adapter should be used.
Note that the driver still supports only one adapter. Note that
the patch does shuffle mxs_i2c_set_bus_speed() to the top of the
driver, but the function remains unchanged.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch just converts the function prototypes used throughout
this driver to match those of the i2c framework. There is so far
no functional change. This patch does not do the deeper integration
of the framework bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch prepares the MXS I2C driver for the conversion to the
new I2C driver framework by pulling out the hard-coded I2C0 address
from all the places.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Include the i2c header and change the non confirming
functions to do so.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Heiko Schocher <hs@denx.de>
[trini: Fix i2c_get_bus_num prototype]
Signed-off-by: Tom Rini <trini@ti.com>
To support the Armada XP SoC, we just need to include the correct header.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The existing i.MX's I2C driver mxc_i2c.c is compatible
with the controller of LS102xA. As I2C's registers
are 8-bit on LS102xA, I2C_QUIRK_REG is enabled to
use 8-bit driver.
This patch is to add I2C 1,2,3 support for LS102xA.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).
The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>
If a bus busy is detected when intializing the driver,
toggle 9 times the scl pin. Therefore enable the test mode
of the controller, in which the scl, sda pins can be
controlled manually.
Tested on the siemens boards pxm2, rut and dxr2.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: Lubomir Popov <lpopov@mm-sol.com>
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Vincent Stehlé <v-stehle@ti.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
IHS I2C master support was merely a hack in the osd driver.
Now it is a proper u-boot I2C framework driver, supporting the
v2.00 master features.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Since tegra_i2c_{read,write}'s debug() call dumps the chip address, dump
the address length (alen) too, so the address value can be correctly
interpreted.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
The Tegra I2C controller's TX FIFO contains 32-bit words. If the final
FIFO entry of a transaction contains fewer than 4 bytes, the driver
currently fills the unused FIFO bytes with uninitialized data. This can
be confusing when reading back the FIFO content for debugging purposes.
Solve this by explicitly initializing the variable containing FIFO data
before filling it (partially) with data. With this change,
send_recv_packets()'s loop's if (is_write) code mirrors the else (i.e.
read) branch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
I2C read transactions are typically implemented as follows:
START(write) address REPEATED_START(read) data... STOP
However, Tegra's I2C driver currently implements reads as follows:
START(write) address STOP START(read) data... STOP
This sequence confuses at least the AS3722 PMIC on the Jetson TK1 board,
leading to corrupted read data in some cases. Fix the driver to chain
the transactions together using repeated starts to solve this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
These are used only once, so their is no need to have them global.
This also stops mvtwsi from using any bss vars making it easier to use
before dram init (to talk to the pmic to set the dram voltage).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The TWSI_FREQUENCY macro was wrong in 2 ways:
1) It was casting the result of the calculations to an u8, while i2c clk
rates are often >= 100Khz which won't fit in a u8, drop the cast.
2) It had an extra factor of 2 in the divider which neither the datasheet nor
the Linux driver have.
The comment for the default value was wrongly saying that m lives in
bits 4-7, while in reality it is in bits 3-6, as can be seen from the correct
shift by 3 used in i2c_init().
While at it remove the unused twsi_actual_speed variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Most of the I2C slaves support accesses in the typical style
that is : read/write series of bytes at particular address offset.
These transactions look like:"
(1) START:Address:Tx:Offset:RESTART:Address[0..4]:Tx/Rx:data[0..n]:STOP"
However there are certain devices which support accesses in
terms of the transactions as follows:
(2) "START:Address:Tx:Txdata[0..n1]:Clock_stretching:
RESTART:Address:Rx:data[0..n2]"
Here Txdata is typically a command and some associated data,
similarly Rxdata could be command status plus some data received
as a response to the command sent.
Type (1) transactions are currently supportd in the
i2c driver using i2c_read and i2c_write APIs. I2C EEPROMs,
RTC, etc fall in this category.
To handle type (2) along with type (1) transactions,
i2c_read() function has been modified.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
This driver needs a data structure in SRAM before SDRAM is available.
This is not alway the case using .data section. Moving this data
structure to global_data guarantees it is writable.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
- add davinci driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
This patch moves the davinci i2c_defs.h file to drivers.i2c directory.
It will allow to reuse the davinci_i2c driver for TI Keystone2 SOCs.
Not used "git mv" command to move the file because small part of
it with definitions specific for Davinci SOCs has to remain in the
arch/arm/include/asm/arch-davinci.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Add support for the Kona I2C controller found on Broadcom mobile SoCs.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
As soon as all boards have their CONFIG_SYS_I2C_BASE defined in
configuration files instead of "asm/arch/hardware.h" it's safe to remove
the inclusion in question and make driver platform-independent.
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Adds support for set-speed on the OMAP24xx I2C Adapter.
Changes to omap24_i2c_write(...) for polling ARDY Bit from IRQ-Status.
Otherwise on a subsequent call the transfer of last byte from the
predecessor is aborted and therefore lost. For exmaple when
i2c_write(...) is followed by a i2c_setspeed(...) (which has to
deactivate and activate master for changing psc,...).
Minor cosmetical changes.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: Heiko Schocher <hs@denx.de>
Make sure the I2C write queue is empty before leaving the mxs_i2c_write().
If we start and I2C write and only wait for ACK, the MXS I2C IP block may
enter next operation while still processing the write aftermath internally.
This will in turn disrupt one or more subsequent transfer(s).
A testcase for this issue is as such. This testcase is also interesting because
the first I2C_WRITE which becomes disruptive happens in the 'i2c read' command.
The 'i2c read' command first uses I2C_WRITE to send I2C address of the chip and
then uses I2C_READ to read data from the chip. After this command completes, the
'i2c probe' will use sequence of I2C_WRITE commands to probe the I2C bus. The
problem is that the first I2C_WRITE disrupted the I2C IP block operation and
this sideeffect propagates all the way to this next I2C_WRITE used by the 'i2c
probe' call. The result is the 'i2c probe' receives an ACK on I2C address 0x00,
even if this ACK was owned by the previous I2C_WRITE operation. Note that the
'i2c read' command must read from a valid I2C chip address.
Wrong:
> i2c probe
Valid chip addresses: 50 51
> i2c read 0x50 0x0.2 0x10 0x42000000
> i2c probe
Valid chip addresses: 00 50 51
With this patch
> i2c probe
Valid chip addresses: 50 51
> i2c read 0x50 0x0.2 0x10 0x42000000
> i2c probe
Valid chip addresses: 50 51
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Enhance the DesignWare I2C driver to support address length more
than 1 byte. This enhancement is required as some I2C slave
device such as EEPROM chip might have 16 bit address byte.
Signed-off-by: Chin Liang See <clsee@altera.com>
Acked-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
The ADI twi peripheral is not binding to Blackfin processor only.
Access i2c registers by standard io functions.
Fix coding style.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Fixed bug with alen == 0 in 'i2c_write', 'i2c_read'
Further minor corrections:
- Write 'address' register before 'data' register.
- Write 'transfer_size' register before 'address' register.
Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The architecture is unmaintained and dead, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
This fixes the following compiler warnings:
fti2c010.c: In function 'fti2c010_read':
fti2c010.c:204:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]
fti2c010.c: In function 'fti2c010_write':
fti2c010.c:266:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
Since we agreed on legacy implementation of "eeprom_{read|write}"
(http://patchwork.ozlabs.org/patch/295825/) I had to fix/make it work
again DesignWare I2C driver for cases when 1 EEPROM IC fake I2C with
anumber of "built-in" ICs with different chip addresses.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin KUMAR <vipin.kumar@st.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
This corrects i2c core to interpret the value returned by
i2c_set_bus_speed as a success indicator rather than the
actual speed that was set. When i2c_set_bus_speed returns
a failure code, the speed is unknown so the adapter speed
is set to zero.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Create the i2c adapter object for the fifth bus on SoC with more than
4 buses. This allow using all the bus available on T30.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds the U_BOOT_I2C_ADAP_COMPLETE defines for channels
on Exynos5420 and Exynos5250 and also adds support for init function
for hsi2c channels
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Writing zero into I2Ci.I2C_CNT register causes random I2C failures in OMAP3
based devices. This seems to be related to the following advisory which
apears in multiple erratas for OMAP3 SoCs (OMAP35xx, DM37xx), as well as
OMAP4430 TRM:
Advisory:
I2C Module Does Not Allow 0-Byte Data Requests
Details:
When configured as the master, the I2C module does not allow 0-byte data
transfers. Note: Programming I2Ci.I2C_CNT[15:0]: DCOUNT = 0 will cause
undefined behavior.
Workaround(s):
No workaround. Do not use 0-byte data requests.
The writes in question are unnecessary from a functional point of view.
Most of them are done after I/O has finished, and the only one that preceds
I/O (in i2c_probe()) is also unnecessary because a stop bit is sent before
actual data transmission takes place.
Therefore, remove all writes that zero the cnt register.
Cc: Heiko Schocher <hs@denx.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lubomir Popov <lpopov@mm-sol.com>
Cc: Enric Balletbo Serra <eballetbo@gmail.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
For a eeprom with a 2-bytes address (e.g., Ateml AT24C1024B),
the r/w address should be serial out in MSB order.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
Stefan Roese
Rob Herring
Masahiro Yamada
Simon Glass
Przemyslaw Marczak
Masahiro Yamada
Peng Fan
Mark Tomlinson
Scott Jiang
Nobuhiro Iwamatsu
Shaveta Leekha
Dirk Eibach
Jeroen Hofstee
Marek Vasut
Wang Huan
Albert ARIBAUD
Hans de Goede
Shengzhou Liu
Heiko Schocher
Tom Rini
York Sun
Stephen Warren
Steve Rae
Jesper B. Christensen
Vitaly Andrianov
Karicheri, Muralidharan
Tetsuyuki Kobayashi
Darwin Rambo
Alexey Brodkin
Hannes Petermaier
Chin Liang See
Sonic Zhang
Michael Burr
Kuo-Jung Su
Hisashi Nakamura
Alban Bedel
Naveen Krishna Ch
Nikita Kiryanov