This patch allows booting from FLASH the ML507 board by Xilinx.
Previously, U-Boot needed to be loaded from JTAG or a Sytem ACE CF
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel. It offers versatile peripherals, such as ethernet, usb
device, usb host etc.
The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).
Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.
For more information see: http:///www.miromico.com/hammerhead
Signed-off-by: Julien May <mailinglist@miromico.ch>
[haavard.skinnemoen@atmel.com: various small fixes and adaptions]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The current implementation of get_timer() is only really useful after we
have relocated u-boot to memory. The i2c code is used before that as part
of the SPD DDR setup.
We actually have a bug when using the get_timer() code before relocation
because the .bss hasn't been setup and thus we could be reading/writing
a random location (probably in flash).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to increased space usage, U-Boot can no longer be stored in three sectors.
The current U-Boot use just over three flash sectors (197k), and U-Boot will
become corrupt after saving environment variables. This patch adds another 64k
to CFG_MONITOR_LEN.
Signed-off-by: Frank E. Svendsbøe <frank.svendsboe@gmail.com>
Because the cmd_tbl_s structure depends on the configuration file, it
must be assured that config.h is included before the structure is
evaluated by the compiler. If this is not certain, it could happen
that the compiler generates structures of different size, depending
on the fact if the source file includes <config.h> before or after
<command.h>.
The effect is that u-boot crashes when tries to relocate the command
table (for ppc) or try to access to the command table for other
architectures.
The problem can happen on board-depending commands. All general
commands under /common are unaffected, because they include already
config.h before command.h.
Signed-off-by: Stefano Babic <sbabic@denx.de>
cmd_ide.c:827: Warnung: weak declaration of `ide_outb' after first use results in unspecified behavior
cmd_ide.c:839: Warnung: weak declaration of `ide_inb' after first use results in unspecified behavior
Signed-off-by: Heiko Schocher <hs@denx.de>
Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.
Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
If CONFIG_SKIP_RELOCATE_UBOOT is set the flag GD_FLG_RELOC is usually
never set, because relocation to RAM is actually never done by U-boot
itself. However, several pieces of code check if this flag is set at
some time.
So, to make sure this flag is set on boards skipping relocation, this
is added to the initialisation of U-boot at a moment where it is safe
to do so.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Prevent i2c_init() in fsl_i2c.c from writing to the data segment before
relocation. Commit d8c82db4 added the ability for i2c_init() to program the
I2C bus speed and save the value in i2c_bus_speed[], which is a global
variable. It is an error to write to the data segment before relocation,
which is what i2c_init() does when it stores the bus speed in i2c_bus_speed[].
Signed-off-by: Timur Tabi <timur@freescale.com>
Use CFG_MIPS_TIMER_FREQ when computing the baudrate divisor
on alchemy cpus.
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Renamed initialization functions for atngw100 and atstk1000.
Removed initializations for these boards from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
map_physmem() takes a phys_addr_t as parameter. This type is defined in
asm/types.h, so we need to include that file.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Some CPU POST tests did not disable the interrupts while running. This
seems to be necessary to protect this self modifying code.
Signed-off-by: Stefan Roese <sr@denx.de>
The SPR IVPR register is only present (as far as I know) for
processors with a PPC440 core.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
Acked-by: Stefan Roese <sr@denx.de>
This patch defines CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL for all
440/460 platforms. This may be needed since those platforms support
36bit physical address space.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a problem with incorrect MODTx (On Die Termination)
setup for a configuration with multiple DIMM's and multiple ranks.
Without this change Katmai was unable to boot Linux with DDR2 frequency
>= 533MHz and mem>=3GB. With this patch Katmai successfully boots Linux
with DDR2 frequency = 640MHz and mem=4GB.
Signed-off-by: Stefan Roese <sr@denx.de>
The Xilinx ML507 Board is a Virtex 5 prototyping board that includes,
among others:
-Virtex 5 FX FPGA (With a ppc440x5 in it)
-256MB of SDRAM2
-32MB of Flash
-I2C Eeprom
-System ACE chip
-Serial ATA connectors
-RS232 Level Conversors
-Ethernet Transceiver
This patch gives support to a standard design produced by EDK for this
board: ppc440, uartlite, xilinx_int and flash
- Includes Changes propossed by Stefan Roese and Michal Simek
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>
-This patchs gives support for the embbedded ppc440
on the Virtex5 FPGAs
-interrupts.c divided in uic.c and interrupts.c
-xilinx_irq.c for xilinx interrupt controller
-Include modifications propossed by Stefan Roese
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>
This got broken by commits 93c56f212c
[cfi_flash: support of long cmd in U-boot.]
That command needs to be in little endian format on BE machines
with CFG_WRITE_SWAPPED_DATA. Without this patch, the command 0xf0
gets saved on stack as 0x00 00 00 f0 and 0x00 gets written into
the cmdbuf in case portwidth = chipwidth = 8bit.
Cc: Alexey Korolev <akorolev@infradead.org>
Cc: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
The thinko was quite silly indeed, I messed with !ptr. Normally this
would trigger some fault, but in U-Boot NULL pointer is equal to phys
0, so the code was working still, just didn't actually test mpc8315erdb
environment variable value. Heh.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Freescale ships MPC8315E-RDB boards either with TSEC1 and USB UTMI
support, or without TSEC1 but with USB ULPI PHY support in addition.
With this patch user can specify desired USB PHY.
Also, it seems that we can't distinguish the two boards in software, so
user have to set `mpc8315erdb' environment variable to either 'tsec1'
(TSEC1 enabled) or `ulpi' (board with ULPI PHY, TSEC1 disabled), so that
Linux will not probe for TSEC1.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Currently U-Boot can only fixup the usb dr_mode, but some boards (namely
MPC8315E-RDB) can use two PHY types: ULPI (stand-alone OTG port) or UTMI
(connected to the four-ports hub, usb host only).
This patch implements support for passing Dual-Role USB controller's
device tree property phy_type through the usb_phy_type environment
variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Round the serial port clock divisor value returned by
calc_divisor()
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Ricardo Ribalda Delgado
Haavard Skinnemoen
Julien May
Kumar Gala
Wolfgang Denk
Frank Svendsbøe
Kyungmin Park
Rafal Jaworowski
Jean-Christophe PLAGNIOL-VILLARD
Stefano Babic
Scott Wood
Heiko Schocher
Adrian Filipi
Remy Bohmer
Timur Tabi
Wolfgang Ocker
Ben Warren
Markus Klotzbuecher
Michal Simek
Gururaja Hebbar K R
Detlev Zundel
Stefan Roese
Niklaus Giger
Sebastian Siewior
Anton Vorontsov
Hugo Villeneuve