Commit graph

13 commits

Author SHA1 Message Date
Masahiro Yamada
0298f4c003 ARM: uniphier: move CONFIG_SPL_* to defconfig or select
As I repeated in the ML, I am unhappy with config entries with bare
defaults.  Kick them out of arch/arm/mach-uniphier/Kconfig.

Currently, CONFIG_SPL_SERIAL_SUPPORT is not user-configurable
(build fails without it), but it should be fixed later anyway,
so I am moving CONFIG_SPL_SERIAL_SUPPORT to defconfigs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-23 00:38:38 +09:00
Tom Rini
06066a7df9 configs: Re-sync
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-20 09:30:07 -04:00
Masahiro Yamada
9b1b6d4225 Revert "Increase default of CONFIG_SYS_MALLOC_F_LEN for SPL_OF_CONTROL"
This reverts commit 90c08d9e08.

I took a closer look at this after the commit was applied, and found
CONFIG_SYS_MALLOC_F_LEN=0x2000 was too much.  8KB memory for SPL is
actually too big for some boards.  Perhaps 0x800 is enough, but the
situation varies board by board.

Let's postpone our decision until we come up with a better idea.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-19 15:20:09 -04:00
Tom Rini
9a6535e05f Merge branch 'master' of git://git.denx.de/u-boot-uniphier 2016-09-18 14:05:30 -04:00
Masahiro Yamada
27350c922e ARM: uniphier: select PINCTRL and SPL_PINCTRL
Now all UniPhier SoCs support a pinctrl driver.  Select (SPL_)PINCTRL
since it is mandatory even for base use.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-09-18 23:10:35 +09:00
Simon Glass
7ace858bf1 Convert CONFIG_SPL_NOR_SUPPORT to Kconfig
Move this option to Kconfig and tidy up existing uses.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-09-16 17:27:16 -04:00
Masahiro Yamada
90c08d9e08 Increase default of CONFIG_SYS_MALLOC_F_LEN for SPL_OF_CONTROL
If both SPL_DM and SPL_OF_CONTROL are enabled, SPL needs to bind
several devices, but CONFIG_SYS_MALLOC_F_LEN=0x400 is apparently
not enough.  Increase the default to 0x2000 for the case.  This
will be helpful for shorter defconfigs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-07 08:48:58 -04:00
Masahiro Yamada
8d11f80413 ARM: uniphier: enable CONFIG_CMD_CACHE
This will be useful, for example, to load firmware to DRAM and make
it visible to other agents.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-08-28 13:12:18 +09:00
Masahiro Yamada
85dc2fe119 ARM: uniphier: change UNIPHIER_SERIAL to default y option
This is very likely to be necessary for normal use cases.
Set its default to 'y' for shorter defconfig files.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-08-28 13:11:35 +09:00
Masahiro Yamada
4fd92db8db ARM: uniphier: move CONFIG_I2C_EEPROM to defconfig
We already have the entry for this option in Kconfig, so let's
migrate to it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-26 17:35:46 -04:00
Masahiro Yamada
7c8ef0feb9 ARM: uniphier: use the default CONFIG_BOOTDELAY=2
I do not insist on CONFIG_BOOTDELAY=3. The default value in Kconfig,
CONFIG_BOOTDELAY=2, is just fine for these boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-20 07:15:39 +09:00
Heiko Schocher
bb597c0eeb common: bootdelay: move CONFIG_BOOTDELAY into a Kconfig option
move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.

Signed-off-by: Heiko Schocher <hs@denx.de>

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2016-06-09 13:53:05 -04:00
Masahiro Yamada
667dbcd01d ARM: uniphier: add PH1-LD11 SoC support
This is a low-cost ARMv8 SoC from Socionext Inc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-05-26 00:37:13 +09:00