Add print_cpuinfo() function and enable
CONFIG_DISPLAY_CPUINFO for keystone platforms,
so that cpu info can be displayed during boot.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DRA72x processor variants are single core and it does not export ACP[1].
Hence, we have no source for generating an external snoop requests which
appear to be key to the deadlock in DRA72x design.
Since we build the same image for DRA74x and DRA72x platforms, lets
runtime detect and disable the workaround (in favor of performance) on
DRA72x platforms.
[1] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438i/BABIAJAG.html
Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add workaround for Cortex-A15 ARM erratum 801819 which says in summary
that "A livelock can occur in the L2 cache arbitration that might
prevent a snoop from completing. Under certain conditions this can
cause the system to deadlock. "
Recommended workaround is as follows:
Do both of the following:
1) Do not use the write-back no-allocate memory type.
2) Do not issue write-back cacheable stores at any time when the cache
is disabled (SCTLR.C=0) and the MMU is enabled (SCTLR.M=1). Because it
is implementation defined whether cacheable stores update the cache when
the cache is disabled it is not expected that any portable code will
execute cacheable stores when the cache is disabled.
For implementations of Cortex-A15 configured without the “L2 arbitration
register slice” option (typically one or two core systems), you must
also do the following:
3) Disable write-streaming in each CPU by setting ACTLR[28:25] = 0b1111
So, we provide an option to disable write streaming on OMAP5 and DRA7.
It is a rare condition to occur and may be enabled selectively based
on platform acceptance of risk.
Applies to: A15 revisions r2p0, r2p1, r2p2, r2p3 or r2p4 and REVIDR[3]
is set to 0.
Note: certain unicore SoCs *might* not have REVIDR[3] not set, but
might not meet the condition for the erratum to occur when they donot
have ACP (Accelerator Coherency Port) hooked to ACE (AXI Coherency
Extensions). Such SoCs will need the work around handled in the SoC
specific manner, since there is no ARM generic manner to detect such
configurations.
Based on ARM errata Document revision 18.0 (22 Nov 2013)
Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Reviewed-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
This switches the Integrator boards over to using the device model
for its serial ports.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current many cpu use the same flush_cache() function, which just call
the flush_dcache_range().
So implement a weak flush_cache() for all the cpus to use.
In original weak flush_cache() in arch/arm/lib/cache.c, there has some
code for ARM1136 & ARM926ejs. But in the arch/arm/cpu/arm1136/cpu.c and
arch/arm/cpu/arm926ejs/cache.c, there implements a real flush_cache()
function as well. That means the original code for ARM1136 & ARM926ejs
in weak flush_cache() of arch/arm/lib/cache.c is totally useless.
So in this patch remove such code in flush_cache() and only call
flush_dcache_range().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Since some driver like ohci, lcd used dcache functions. But some ARM
cpu don't implement the invalidate_dcache_range()/flush_dcache_range()
functions.
To avoid compiling errors this patch adds an weak empty stub function
for all ARM cpu in arch/arm/lib/cache.c.
And ARM cpu still can implemnt its own cache functions on the cpu folder.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: York Sun <yorksun@freescale.com>
gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
When using dcache the setup data for the mailbox must be actually written
into memory before calling into firmware. Thus flush and invalidate the
memory.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
As both cores are similar merge the cache handling code for both CPUs
to arm11 directory.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
[trini: Add hunk to arch/arm/cpu/arm1136/Makefile]
Signed-off-by: Tom Rini <trini@konsulko.com>
Apparently lcd_panel_disable is not defined anywhere, so no config for
an arm1136 board would have set CONFIG_LCD. Remove the unused code.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
The LG Optimus Black (P970) codename sniper is a smartphone that was designed
and manufactured by LG Electronics (LGE) and released back in 2011.
It is using an OMAP3630 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up. This port is aimed at running an Android version
such as Replicant, the fully free Android distribution. However, support for
upstream Linux with device-tree and common GNU/Linux distros boot commands
could be added in the future.
For more information about the journey to freeing this device, please read the
series of blog posts at:
http://code.paulk.fr/article20/a-hacker-s-journey-freeing-a-phone-from-the-ground-up-first-part
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add CONFIG_OF_SUPPORT]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reboot mode is written in scratchpad memory before reboot in the form of a
single char, that is the first letter of the reboot mode string as passed to the
reboot function.
This mechanism is supported on OMAP3 both my the upstream kernel and by various
TI kernels.
It is up to each board to make use of this mechanism or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The change adds SPL build support to Timll DevKit3250 board, the
generated SPL image can be uploaded over UART5, JTAG or stored on
NAND. SPL is designed to load U-boot image from NAND.
All new NAND chip defines in board configuration are needed by
SPL NAND "simple" framework, the framework is used to reduce
potentially duplicated code from LPC32xx SLC NAND driver.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds support of LPC32xx SLC NAND controller.
LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.
This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.
Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.
The driver can be included to an SPL image.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Enable BCM SF2 ethernet and PHY for BCM Cygnus SoC
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
add support for the at91sam9260 based board smartweb from
siemens. SPL is used without serial support, as this
SoC has only 4k sram for running SPL. Here a U-Boot
bootlog:
RomBOOT
>
U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200)
CPU: AT91SAM9260
Crystal frequency: 18.432 MHz
CPU clock : 198.656 MHz
Master clock : 99.328 MHz
Watchdog enabled
DRAM: 64 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: macb0
Hit any key to stop autoboot: 0
U-Boot>
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch enables building SPL without
CONFIG_SPL_SERIAL_SUPPORT support.
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Ensure we build arch/arm/imx-common on mx28]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a few extra sunxi display registers and constant defines.
Also rename some existing defines (e.g. dropping _GCTRL) and make
some more generic (e.g. dropping the 2x scaling from
SUNXI_LCDC_TCON1_TIMING_V_TOTAL).
This is a preparation patch for adding composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
To enable NAND flash in sunxi SPL,
pins 0-6, 8-22 and 24 on port C are configured.
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add code which uses the new functions for obtaining FPGA ID from
the scan manager. This new code prints the FPGA model attached to
the SoCFPGA during boot and sets environment variable "fpgatype",
which can be used to determine the FPGA model in U-Boot scripts.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Add code to get the FPGA type for Altera's SoCFPGA family of FPGA. The code
uses the scan manager to send jtag pulses that will return the FPGA ID.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Factor out the code which sends JTAG instruction followed by data
into separate function to tidy the code up a little.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Clean up the horrible macros present in the scan_manager.h . Firstly,
the function scan_mgr_io_scan_chain_prg() is static, yet all the macros
are used only within it, thus there is no point in having them in the
header file. Moreover, the macros are just making the code much less
readable, so remove them instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce generic function for accessing the JTAG scan chains in the
SCC manager. Make use of this function throughout the SCC manager to
replace the ad-hoc writes to registers and make the code less cryptic.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Rework this function so it's clear that it is only polling for certain
bits to be cleared. Add kerneldoc. Fix it's return value to be either
0 on success and -ETIMEDOUT on error and propagate this through the
scan manager code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager
configuration values in board file. Introduce a complementary function,
socfpga_get_sdram_rwmgr_config(), which returns this the structure.
This is another step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce two wrapper functions, socfpga_get_seq_ac_init() and
socfpga_get_seq_inst_init() to avoid direct inclusion of the
sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS
generated files. This reduces namespace pollution again.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Zap non-existent functions and place function prototypes at the
beginning of the header file.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce socfpga_sdram_get_config() function implement in a board file,
which returns the socfpga_sdram_config structure. This is the last step
in cleaning up the socfpga_mmr_init_full(), but not the last step which
allows removing the inclusion of sdram.h from drivers/ddr/altera/sdram.c
thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Add a small workaround into the platform code which forces the SDMMC
into 8-bit mode (the default configuration for all socfpga platforms)
to work around breakage caused by missing patches in mainline which
switch the probing of SD/MMC to OF instead of static configuraiton.
The patches will hit mainline after the SPL series, so to avoid build
issues, add this small temporary workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
Now that the SPL structure is organised such that it matches the
U-Boot's SPL design, it is possible to use the option of relocating
GD to RAM. And since we have GD in RAM, move malloc area to RAM as
well. We point the malloc base pointer 1 MiB past U-Boot's load
address. We use simple malloc for SPL because it is 3kiB smaller
in terms of code size than regular malloc which was used thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Reset the GMAC ethernets based on the "resets" OF node instead of ad-hoc
hardcoded values in the U-Boot code. Since we don't have a proper reset
framework in place yet, we have to do this slightly ad-hoc parsing of the
OF tree instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The GMAC can now be probed from OF, so enable DM ethernet and remove the
old ad-hoc designware_initialize() invocation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
setenv an environment variable called "bootmode" , which contains the
board boot mode. This can be in turn used in scripts to determine from
where to load kernel and such.
Signed-off-by: Marek Vasut <marex@denx.de>
Add support for printing from which device the SoCFPGA board booted.
This decodes the BSEL settings and prints it in human readable form.
Signed-off-by: Marek Vasut <marex@denx.de>
Write necessary magic value into the Warm Boot from ON-Chip RAM
group Enable register to enable Warm reset support. Instead of
doing this in the reset_cpu() function, we do it in arch early
init to avoid breaking old kernel code which expects this magic
value to be already written into this register.
This magic is originally excavated from common/spl/spl.c in the
u-boot port from altera, where this value was written just before
the SPL jumped to actual U-Boot in the RAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Rework spl_boot_device() such that it reads the BSEL settings from
system manager and decides from where to load U-Boot based on this
information.
Signed-off-by: Marek Vasut <marex@denx.de>
Add code and configuration options to support booting from QSPI NOR.
Enable support for booting from QSPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
Add code and configuration options to support booting from RAW
SD/MMC card as well as for ext4/vfat filesystems. Enable support
for booting from SD/MMC card, but don't enable the filesystem
support just yet to retain compatibility with old SoCFPGA card
format.
Signed-off-by: Marek Vasut <marex@denx.de>
Remove the custom SPL linker script, use the generic one instead.
The custom script doesn't bring in anything new and is only burden
to maintain.
Signed-off-by: Marek Vasut <marex@denx.de>
The code in spl_board_init() should have been in board_init_f()
from the beginning, since it is code which configures system and
then starts DRAM. Thus, it cannot be in spl_board_init(), which
is called from board_init_r() , which already expects a working
DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Make sure that all the peripherals are correctly reset and then
brought out of reset in the SPL. Not going through proper reset
cycle might leave the IP blocks in inconsistent state.
Signed-off-by: Marek Vasut <marex@denx.de>