Commit graph

117 commits

Author SHA1 Message Date
Edgar E. Iglesias
721aed7912 net: phy: Add support for Texas Instruments DP83867
Code is taken from Linux kernel driver (v4.2).

Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-11-19 13:09:21 +01:00
Vincent BENOIT
5ea667ea2f pengwyn: nand and ethernet fixes
-> Add National instrument ethernet transceiver configuration used (DP83848)
-> Change cpsw slave phy address
-> modify nand configuration to use the correct ECC and correct nand features
2015-11-12 18:13:19 -05:00
Bin Meng
17ecfa9b45 net: phy: Test previous phydev->dev against new mac dev
In phy_connect_dev(), if the phy device has an accociated mac device
before, a warning message will be printed. But we should test the
old device against the new one, if they are actually the same one,
don't print the warning message.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-10-29 14:05:49 -05:00
Bin Meng
3e1949d774 net: phy: Change to print all phys that are not found
In get_phy_device_by_mask(), when no phy is found, currently we only
print a message to show the first phy address that is not found. But
this is not always the case as multiple phys can be specified by
phy_mask. Change to print all phys that are not found, and to reduce
the console boot log, change to use 'debug' instead of 'printf'.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-10-29 14:05:49 -05:00
Bin Meng
0132b9ab6e net: phy: Don't create phy device when there is no phy
In get_phy_device_by_mask(), when no phy is found, we should not
create any phy device.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-10-29 14:05:48 -05:00
Sylvain Rochet
4f485150cf net: phy: micrel: disable NAND-tree for KSZ8051
NAND-tree is used to check wiring between MAC and PHY using NAND gates
on the PHY side, hence the name.

NAND-tree initial status is latched at reset by probing the IRQ pin.
However some devices are sharing the PHY IRQ pin with other peripherals
such as Atmel SAMA5D[34]x-EK boards when using the optional TM7000
display module, therefore they are switching the PHY in NAND-tree test
mode depending on the current IRQ line status at reset.

This patch ensure PHY is not in NAND-tree test mode only for the Micrel
KSZ8051 PHY used by Atmel. There are other Micrel PHY affected but I
doubt they are used on such weird hardware design.

Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-10-29 14:05:48 -05:00
Sylvain Lemieux
6617f87668 net: phy: micrel: add support for KSZ8021RNL & KSZ8031RNL
This patch adds support for Micrel KSZ8021RNL & KSZ8031RNL.

Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-10-29 14:05:46 -05:00
Mugunthan V N
26d3acdab8 net: phy: on phy device create do not initialize link to 1
Currently when phy device is created the link variable is
initialized to 1 which denoted phy link is already up. On a power
reset there is no issue as phy status register link status will
not be set, so phy auto negotiate will be started. But when a cpu
reset is issued (ex: dra72x-evm) phy's link status bit is already
set which leads to assume that link is already setup in
genphy_update_link() initial check which results in ehternet not
working. So do not assume that link is already up and on phy
device create set link to zero. This is verified on dra72x-evm.

Reported-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-09-29 16:01:29 -05:00
Prabhakar Kushwaha
4c2620dd71 net: phy/vitesse: Add support for VSC8584 phy
Add support of VSC8584 phy placed on new QSGMII/SGMII ethernet riser cards
used on LS2085QDS platforms.

Signed-off-by: King Chung Lo@freescale.com <KingChungLo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-01 21:38:39 -05:00
Jiandong Zheng
1b564cecc3 net: phy: broadcom: Add BCM Cygnus PHY
Add Ethernet PHY for BCM Cygnus SoC

Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-08-11 13:49:17 -05:00
Jörg Krause
59370f3fcd net: phy: delay only if reset handler is registered
With commit e3a77218a2 the MII bus is only
reset if a reset handler is registered. If there is no reset handler there
is no need to wait for a device to come out of the reset.

Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2015-08-11 13:48:25 -05:00
Jörg Krause
2c171a2a5f net: phy: fix data type of phy_id
phy_id is declared as u32 in create_phy_by_mask and in struct phy_device.

Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2015-08-11 13:47:15 -05:00
Clemens Gruber
8396d0ab8b net: Add support for Marvell 88E1510 PHY
Support the 88E1510 PHY which is very similar to the 88E1518.
I also set the INTn output and configured the LEDs.

Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-08-11 13:29:01 -05:00
Clemens Gruber
90a94ef652 net: Improve 88E151x PHY initialization
- The EEE fixup magic should also be enabled for RGMII
- Improved comments

Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-08-11 13:28:59 -05:00
Shengzhou Liu
90712741c9 net/phy: set led for rtl8211f phy
Initialize LCR rigister to configure
green LED for Link, yellow LED for Active.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2015-08-11 13:20:34 -05:00
Michal Simek
abbfcbe58e net: phy: Add support for all targets which requires MANUAL_RELOC
Targets with CONFIG_NEEDS_MANUAL_RELOC do not use REL/RELA
relocation (mostly only GOT) where functions aray are not
updated. This patch is fixing function pointers passed to phy_register
function.
This patch was tested on Microblaze architecture.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-05-19 13:33:21 -05:00
Shengzhou Liu
793ea94770 net/phy: refactor RTL8211F initialization
RTL8211F needs to enalbe TXDLY for RGMII during
phy initialization, so move it to rtl8211f_config
for early initialization.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-05-19 13:33:21 -05:00
Shengzhou Liu
3d6af748eb net/phy: Add support for realtek RTL8211F
RTL8211F has different registers from RTL8211E.
This patch adds support for RTL8211F PHY which
can be found on Freescale's T1023 RDB board.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-05-19 13:33:20 -05:00
pankaj chauhan
8bb065630f net/phy/cortina: Fix compilation warning
Fix comilation warning which is emitted when
firmware address is more than 32 bit.

Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2015-04-23 08:55:57 -07:00
Shengzhou Liu
5707d5ffd4 net/phy: fixup for get_phy_id
commit 3c6928fd7b "net: phy: fix warnings with W=1" caused
some PHYs(e.g. CS4315/CS4340) not working. This patch fixes the
warning and make those special PHYs working as well.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2015-04-20 17:57:13 -05:00
Luca Ellero
c6a40f6e51 net: phy: micrel: add support for KSZ8081MNX
This patch adds a support for KSZ8081MNX in MII mode.

Signed-off-by: Luca Ellero <luca.ellero@brickedbrain.com>
Acked-by: Pavel Machek <pavel@denx.de>
2015-04-20 17:57:12 -05:00
Codrin Ciubotariu
3cee138892 net: phy: realtek: Disable interrupt on Realtek Ethernet PHY drivers
Some Realtek Ethernet PHYs, like RTL8211D(G/N) and RTL8211E(G), have
interrupts enabled by default. If the interrupt is not treated later by
the OS and the PHY's interrupt line is enabled and shared with other
interrupts, the system will get an interrupt storm. This patch disables
the interrupt for PHY devices that use one of the current Realtek
Ethernet PHY drivers. Some of Realtek Ethernet PHYs, such as RTL8211B(L)
have the interrupt masked. In this case, the functionality of the PHY
should not be afected since this patch brings INER and INSR registers to
their default values.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-04-20 17:57:11 -05:00
Simon Glass
c74c8e6651 dm: net: Adjust PHY interface to work with CONFIG_DM_ETH
When driver model is used for Ethernet a few functions are passed a udevice
instead of an eth_device. Also add a function to find a PHY type given its
name. This will be used to decode the device tree node.

Finally, put a phy_interface field in struct eth_pdata since this is an
important part of the platform data for Ethernet.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-04-18 11:11:36 -06:00
Philippe De Muyter
b7a5b08438 net: phy: micrel: add support for KSZ8895 switch in SMI mode
This patch adds a phy driver for the Micrel KSZ8895 switch.  As the SoC MAC
is directly connected to the switch MAC the link to the switch is always up.

But the KSZ8895 switch can be hardwired in three configuration modes :
- not configurable with eventually an eeprom-stored configuration
- configurable by the mdio/mdc connection (SMI protocol)
- configurable by a SPI connection.

In not configurable mode, the switch starts automatically, but in the
other modes, it must be started programmatically, by writing 1 in
configuration register 1.
We only support the not configurable and mdio/mdc (aka SMI) modes here.

Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2015-01-30 15:55:00 -06:00
Shaohui Xie
f7c38cf827 phylib: add support for aquantia PHYs
This patch supports AQ1202, AQ2104, AQR105 PHY.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16 09:32:11 -08:00
Shengzhou Liu
c18fc2c960 net/phy: enable serdes auto-negotiation for vsc8514 phy
VSC8514 QSGMII PHY requires enabling auto-negotiation,
otherwise it wouldn't work.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:15 -08:00
Shengzhou Liu
9b18e5199e net/phy: Add support for CS4315/CS4340 PHY
Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
  to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
  we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:11 -08:00
Hao Zhang
35fa0dda0c net: phy: marvell: add errata w/a for 88E151* chips
As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/88E1514
Rev A0, Errata Section 3.1 Marvell PHY has an errata which requires
that certain registers get written in order to restart
autonegotiation.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2014-11-06 11:04:38 -05:00
Tom Rini
5aa7bece10 Merge branch 'master' of git://git.denx.de/u-boot-ti 2014-10-27 09:05:43 -04:00
Jeroen Hofstee
3c6928fd7b net: phy: fix warnings with W=1
get_phy_id is marked weak but has no protype nor a
strong version, just make it static. Use __weak for
board_phy_config.

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 07:01:59 -04:00
Khoronzhuk, Ivan
adc9a79f3f net: phy: print a number of phy that is not found
In case when several Ethernet ports are supported it's
convenient to see the number of phy that is not found.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-23 11:27:28 -04:00
Pavel Machek
58ec63d6bc net: phy: Cleanup drivers/net/phy/micrel.c
Old saying says that more than three exclamation marks in a row are
sign of mental disease. Cleanup micrel.c.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Chin Liang See <clsee@altera.com>
2014-10-06 17:36:40 +02:00
Masahiro Yamada
368b4d2b49 drivers: net: remove dead drivers
The following configs are not defined at all:

 - CONFIG_INCA_IP_SWITCH
 - CONFIG_PBL2800_ETHER
 - CONFIG_PHY_ICPLUS

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-21 12:01:11 -04:00
maxin.john@enea.com
79e86ccb37 vitesse: remove duplicated argument to ||
Remove the duplicated argument to || check

Signed-off-by: Maxin B. John <maxin.john@enea.com>
2014-08-09 11:17:02 -04:00
Cormier, Jonathan
08be2836df phy: fix create_phy_by_mask for when its given an actual search mask
get_phy_id returns -EIO when it can't read from a phy at a given addr.  This would cause
create_phy_by_mask to return prematurely before it had tested the other addresses in the provided mask.

Example usage:
Replace
    phydev = phy_connect(bus, phy_addr, dev, phy_if)
with
    phydev = phy_find_by_mask(bus, phy_mask, phy_if)
    if (phydev)
	phy_connect_dev(phydev, dev);

Signed-off-by: Cormier, Jonathan <jcormier@criticallink.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
2014-06-05 14:44:56 -04:00
Chunhe Lan
ffc8667acf net: phy/vitesse: Add support for VSC8664 phy module
This patch adds support for VSC8664 PHY module which can
be found on Freescale's T4240RDB boards.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:24:05 -05:00
Shengzhou Liu
597fe041a8 net/phy: enable get_phy_id redefinable
As some PHYs have non-standard PHY ID registers, PHY Id can't
be read correctly by current get_phy_id function, so we enable
get_phy_id redefinable to permit specific PHY driver having own
specific get_phy_id function.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2014-05-12 15:19:45 -04:00
Xiaobo Xie
02aa4c5388 AR8035/phy: Enable autonegotiation function for ar8035
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before,
but used "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8035
to enable autonegotiation. Then removed the genphy_config_aneg() function.

Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
2014-05-12 15:19:45 -04:00
Zhao Qiang
08ad9b068a ar8031: modify the config func of ar8031 to ar8021_config
ar8031 has the same config steps with ar8021, so change its
config func to ar8021_config instead of genphy_config.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:53 -07:00
Codrin Ciubotariu
44afbbc0f0 net/phy: Fix PHY id for VSC8514
In the current Datasheet for VSC8514 there is a mistake, saying that
the PHY id is 0x70570. The real value in the identifier registers is
0x70670. Linux PHY driver uses 0x70670 also.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:47 -07:00
Haijun.Zhang
dc116bd6c4 net/phy: Correct AR8021 phy_mask
There was wrong phy_mask for AR8021 device,
so the AR8021 can't be probed correctly.
Changed it from 0x4fffff to 0x4ffff0.

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
2014-03-07 10:59:06 -05:00
Tom Rini
a7e8c15f71 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-25 13:55:49 -05:00
Zhao Qiang
e0d809647f ar8031/8033/phy:enable autonegotiation for ar8031/8033
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before
while "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8031/8033
to enable autonegotiation.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-02-24 15:23:41 -08:00
Heiko Schocher
9137d19bdd net, phy: atheros ar803x bug
commit 626ee1e3 "phylib: update atheros ar803x phy"

leads in failing ethernet on the pxm2 board.

Calling genphy_config() instead of ar8021_config(),
which seems for ar8021 phys not ar803x phys, make
it working again.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
2014-02-19 10:47:33 -05:00
Fabio Estevam
f66e3ded61 net: phy: atheros: Fix the masks for AR8031/8035
Use the same masks as used in the kernel:
https://git.kernel.org/cgit/linux/kernel/git/stable/linux-stable.git/tree/drivers/net/phy/at803x.c?id=refs/tags/v3.12.6

With such changes Ethernet is functional on hummingboard solo.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Marek Vasut <marex@denx.de>
Patch: 306640
2014-01-14 14:00:41 -06:00
David Dueck
f27f3b5266 phy: Use general phy code for smsc lan8720a
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
2013-11-22 17:03:20 -06:00
David Dueck
3a530d1b3e phy: Use supported field during autonegotiation
The current code incorrectly detects gigabit capabilities for some
100Mbit/s phys. (lan8720a)

Signed-off-by: David Dueck <davidcdueck@googlemail.com>
2013-11-22 17:03:20 -06:00
Fabio Estevam
e003ba5bfc net: phy: atheros: Fix masks for AR8035 and AR8021
The masks were ignoring the last 4 bits which didn't allow detection differences
between the ar8031 and ar8035.

Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Patch: 288018
2013-11-22 17:03:18 -06:00
Chunhe Lan
3177457853 net/phy: Fix the phy id mask of AR8031
The both AR8031 and AR8035 belong to Atheros 803x serial PHY.
So the phy id mask of AR8031 is the same to the phy id mask
of AR8035. The right mask value is 0x4fffff.

This patch has been tested on the P1010 and P1023.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Patch: 287748
2013-11-22 17:03:18 -06:00
Heiko Schocher
dfcaa61c33 net, phy: fix AR8031 phy_mask
AR8035 driver will be never applied because of wrong mask for
AR8031 driver. Fix this.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Pavel Nakonechny <pavel.nakonechny@skitlab.ru>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Patch: 276944
2013-11-22 16:50:54 -06:00