Commit graph

6 commits

Author SHA1 Message Date
Wolfgang Denk
f0c0b3a9e6 Fix incorrect use of getenv() before relocation
A large number of boards incorrectly used getenv() in their board init
code running before relocation.  In some cases this caused U-Boot to
hang when certain environment variables grew too long.
Fix the code to use getenv_r().

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: The LEOX team <team@leox.org>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Georg Schardt <schardt@team-ctech.de>
Cc: Werner Pfister <Pfister_Werner@intercontrol.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Peter De Schrijver <p2@mind.be>
Cc: John Zhan <zhanz@sinovee.com>
Cc: Rishi Bhattacharya <rishi@ti.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
2011-05-12 19:48:42 +02:00
Stefan Roese
cf1971c1c0 ppc4xx: t3corp: Add support for the Xilinx DS617 flash chip
The t3corp board has an Xilinx DS617 flash chip connected to the
onboard FPGA. This patch adds support for these chips. Board
specific flash accessor functions are needed, since the chips
can only be read correctly in 16bit mode.

Additionally the FPGA chip-selects are configured for device-paced
transfers (ready is enabled).

Signed-off-by: Stefan Roese <sr@denx.de>
2010-12-17 09:43:23 +01:00
Stefan Roese
0988776288 ppc4xx: Move gpio.h to ppc4xx-gpio.h since its ppc4xx specific
Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23 09:02:05 +02:00
Stefan Roese
b36df56115 ppc4xx: Move ppc4xx headers to powerpc include directory
This patch moves some ppc4xx related headers from the common include
directory (include/) to the powerpc specific one
(arch/powerpc/include/asm/). This way to common include directory is not
so cluttered with files.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23 09:02:05 +02:00
Stefan Roese
5bf39a96c2 ppc4xx: T3CORP fixes and updates
This patch fixes some problems for the T3CORP board. Here the list
of the changes:

- Add 600-67 and 677 CPU frequency setting to chip_config
  command
- Define CONFIG_DDR_RFDC_FIXED on t3corp:
  While using the "normal" auto calibration code, sometimes values for
  RFDC were picked (>= T3) that resulted in a non-working U-Boot (hang
  upon relocation, while running from SDRAM). With this optimized RFDC
  value we can force this register and use the auto-calibration code to
  setup the remaining calibration registers.
- Increase sizes of FPGA chips selects
- EBC timing updated OEN=3 for 66 MHz EBC speed
- Change ext. IRQ2 setup to level-low active
- Enable CONFIG_SYS_CFI_FLASH_STATUS_POLL

By defining CONFIG_SYS_CFI_FLASH_STATUS_POLL, DQ7 is polled to detect the
chip busy status. This is now used instead of the data toggle method which
is used historically by default in the common CFI driver. With this change
a problem with not written data is solved on this board, where a 32 byte
block of data is still erased instead of filled with the correct content
after these commands:

=> erase 0xfc100000 +0x1000000

....................................................................
done
Erased 128 sectors
=> cp.b 0x100000 0xfc100000 0x1000000
Copy to Flash... done
=> cmp.b 0x100000 0xfc100000 0x1000000
byte at 0x00d0d6c0 (0x00) != byte at 0xfcd0d6c0 (0xff)
Total of 12637888 bytes were the same

Signed-off-by: Stefan Roese <sr@denx.de>
2010-07-23 09:53:48 +02:00
Stefan Roese
273ed0370d ppc4xx: Add T3COPR board support (PPC460GT based)
This patch adds support for the T3CORP board, based on the
AppliedMicro (APM) PPC460GT.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-07-01 10:26:30 +02:00