Commit graph

349 commits

Author SHA1 Message Date
Wolfgang Denk
030ec52f8c board/amcc/taihu/flash.c: Fix compile warning
Fix warnings:
flash.c: In function 'write_word_1':
flash.c:696: warning: dereferencing type-punned pointer will break strict-aliasing rules
flash.c: In function 'write_word_2':
flash.c:1044: warning: dereferencing type-punned pointer will break strict-aliasing rules

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2009-09-15 00:28:24 +02:00
Stefan Roese
d1c3b27525 ppc4xx: Big cleanup of PPC4xx defines
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:

- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
  user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines

Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-09-11 10:35:58 +02:00
Stefan Roese
514bab6609 ppc4xx: Fix "chip_config" command for AMCC Arches
This patch fixes the "chip_config" command for I2C bootstrap EEPROM
configuration. First it changes the I2C bootstrap EEPROM address to
0x54 as this is used on Arches (instead of 0x52 on Canyonlands/
Glacier). Additionally, the NAND bootstrap settings are removed
for Arches since Arches doesn't support NAND-booting.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-08-18 09:16:33 +02:00
Stefan Roese
c3fa4f0c86 ppc4xx: Add support for PPC460EX/460GT rev B chip to AMCC Canyonlands
This patch is based on a diff created by Phong Vo from AMCC.

Signed-off-by: Phong Vo <pvo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-30 07:22:18 +02:00
Stefan Roese
042d01c72e ppc4xx: Fix problem with NOR range assignment in Canyonlands ft_board_setup
This patch fixes the problem, that the current fdt board fixup code only
set's one range, the one for NOR. By this it's overwriting the already
correctly configured values done in __ft_board_setup(). Just remove this
now unneeded NOR fixup and all the ranges are correctly defined.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Felix Radensky <felix@embedded-sol.com>
2009-07-28 07:26:07 +02:00
Stefan Roese
11a1604f8d ppc4xx: Add some NAND-booting bootstrap entries to Kilauea chip_config cmd
This patch adds some I2C bootstrap setting for NAND booting to the Kilauea
chip_config command ("533-nand" and "600-nand").

Additionally some incorrectly indented lines are fixed.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-28 07:24:01 +02:00
Stefan Roese
f3ed3c9b74 ppc4xx: Fix Arches DDR2 initialization
Testing on AMCC Arches with the latest U-Boot version yielded that DDR2
initialization is currently broken. U-Boot hangs upon relocation to SDRAM
or crashes with random traps. This patch fixes this problem. Arches now
uses a different WRDTR and CLKTR default setting than Canyonlands/Glacier.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-28 07:22:46 +02:00
Stefan Roese
4b1389e0ce ppc4xx: Add chip_config command to AMCC Kilauea eval board
This patch removes the "alterpll" command and replaces it with the now
ppc4xx standard "chip_config" command to configure the I2C bootstrap
EEPROM.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-24 09:56:40 +02:00
Stefan Roese
87c0b72908 Add "chip_config" command for PPC4xx bootstrap configuration
This patch adds a generic command for programming I2C bootstrap
eeproms on PPC4xx. An implementation for Canyonlands board is
included.

The command name is intentionally chosen not to be PPC4xx specific.
This way other CPU's/SoC's can implement a similar command under
the same name, perhaps with a different syntax.

Usage on Canyonlands:

=> chip_config
Available configurations (I2C address 0x52):
600-nor          - NOR  CPU: 600 PLB: 200 OPB: 100 EBC: 100
600-nand         - NAND CPU: 600 PLB: 200 OPB: 100 EBC: 100
800-nor          - NOR  CPU: 800 PLB: 200 OPB: 100 EBC: 100
800-nand         - NAND CPU: 800 PLB: 200 OPB: 100 EBC: 100
1000-nor         - NOR  CPU:1000 PLB: 200 OPB: 100 EBC: 100
1000-nand        - NAND CPU:1000 PLB: 200 OPB: 100 EBC: 100
1066-nor         - NOR  CPU:1066 PLB: 266 OPB:  88 EBC:  88 ***
1066-nand        - NAND CPU:1066 PLB: 266 OPB:  88 EBC:  88
=> chip_config 600-nor
Using configuration:
600-nor          - NOR  CPU: 600 PLB: 200 OPB: 100 EBC: 100
done (dump via 'i2c md 52 0.1 10')
Reset the board for the changes to take effect

Other 4xx boards will be migrated to use this command soon
as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2009-07-24 06:42:32 +02:00
Felix Radensky
26d37f0061 ppc4xx: Fix FDT EBC mappings on Canyonlands
This patch fixes 2 problems with FDT EBC mappings on Canyonlands.
First, NAND EBC mapping was missing, making Linux NAND driver
unusable on this board. Second, NOR remapping code assumed that
NOR is always on CS0, however when booting from NAND NOR is on CS3.

Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-08 10:59:06 +02:00
Wolfgang Denk
a89c33db96 General help message cleanup
Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.

Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.

This patch cleans this up - for example:

Before:
	=> help dtt
	dtt - Digital Thermometer and Thermostat

	Usage:
	dtt         - Read temperature from digital thermometer and thermostat.

After:
	=> help dtt
	dtt - Read temperature from Digital Thermometer and Thermostat

	Usage:
	dtt

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-06-12 20:47:16 +02:00
Stefan Roese
d873133f2b ppc4xx: Add Sequoia RAM-booting target
This patch adds another build target for the AMCC Sequoia PPC440EPx
eval board. This RAM-booting version is targeted for boards without
NOR FLASH (NAND booting) which need a possibility to initially
program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000)
configured to setup the SDRAM, this debugger can load this RAM-
booting image to the target address in SDRAM (in this case 0x1000000)
and start it there. Then U-Boot's standard NAND commands can be
used to program the NAND FLASH (e.g. "nand write ...").

Here the commands to load and start this image from the BDI2000:

440EPX>reset halt
440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin
440EPX>go 0x1000000

Please note that this image automatically scans for an already
initialized SDRAM TLB (detected by EPN=0). This TLB will not be
cleared. This TLB doesn't need to be TLB #0, this RAM-booting
version will detect it and preserve it. So booting via BDI2000
will work and booting with a complete different TLB init via
U-Boot works as well.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:39:47 +02:00
Stefan Roese
17c1b0e89b ppc4xx: Remove unused code for Sequoia NAND booting version
The current define of get_bus_freq() in the CONFIG_NAND_SPL #ifdef is not
used at all. This patch changes it's define to the currently used value of
133333333 and removes the unnecessary code.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-04-16 09:12:08 +02:00
Stefan Roese
5132106a27 ppc4xx: Fixup chip-selects in dtb for NAND-booting Sequoia
Currently the NOR & NAND support in Linux only works for the "standard"
Sequoia, the version booting for NOR flash. The NAND-booting version
has the chip-selects swapped. Here the chip-select mappings:

"Standard" NOR-booting version:
CS0	NOR
CS3	NAND

NAND-booting version:
CS0	NAND
CS3	NOR

With this path the dtb gets fixed-up, so that the correct chip-select
numbers are patched in the dtb enabling correct NOR & NAND support
in Linux on the NAND-booting Sequoia version.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-04-16 09:12:08 +02:00
Stefan Roese
3edf68c47f ppc4xx: Sequoia: Fix TLB reassignment in NAND booting code
This patch fixes a bug in the Sequoia TLB init code to reconfigure
the correct TLB (boot space) after running from RAM. This bug was
introduced with patch 4d332dbeb0
[ppc4xx: Make Sequoia boot vxWorks] which changed the order of the
TLB in the Sequoia init.S file.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-26 18:36:40 +01:00
Trent Piepho
f62fb99941 Fix all linker script to handle all rodata sections
A recent gcc added a new unaligned rodata section called '.rodata.str1.1',
which needs to be added the the linker script.  Instead of just adding this
one section, we use a wildcard ".rodata*" to get all rodata linker section
gcc has now and might add in the future.

However, '*(.rodata*)' by itself will result in sub-optimal section
ordering.  The sections will be sorted by object file, which causes extra
padding between the unaligned rodata.str.1.1 of one object file and the
aligned rodata of the next object file.  This is easy to fix by using the
SORT_BY_ALIGNMENT command.

This patch has not be tested one most of the boards modified.  Some boards
have a linker script that looks something like this:

*(.text)
. = ALIGN(16);
*(.rodata)
*(.rodata.str1.4)
*(.eh_frame)

I change this to:

*(.text)
. = ALIGN(16);
*(.eh_frame)
*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))

This means the start of rodata will no longer be 16 bytes aligned.
However, the boundary between text and rodata/eh_frame is still aligned to
16 bytes, which is what I think the real purpose of the ALIGN call is.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
2009-03-20 22:39:12 +01:00
Mikhail Zolotaryov
ee86fd15e1 Fix AMCC Sequoia board DDR memory configuration
Sequoia board schematics (DES0211_11_SCH_11.pdf, page 5, unit U1D)
specifies that BankSel#1 is not connected, while bootloader memory
configuration is (board/amcc/sequoia/sdram.c):
       mtsdram(DDR0_10, 0x00000300);
i.e. both Chip Selects used - not correct.

If we change to correct value here:
       mtsdram(DDR0_10, 0x00000100);
memory is accessible OK also.

Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-17 10:52:36 +01:00
Stefan Roese
cef0efaf2f ppc4xx: Fix problem with board_eth_init() vs cpu_eth_init() on AMCC boards
Some AMCC eval boards do have a board_eth_init() function calling
pci_eth_init(). These boards need to call cpu_eth_init() explicitly now
with the new eth_init rework.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-12 06:08:07 +01:00
Peter Tyser
2fb2604d5c Command usage cleanup
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-28 08:49:52 +01:00
Peter Tyser
79621bc10b amcc: Clean up command usage output
Update taihu and taishan commands to use cmd_usage() function
to display usage messages.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-28 08:43:52 +01:00
Peter Tyser
62c3ae7c6e Standardize command usage messages with cmd_usage()
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-28 08:43:45 +01:00
Dave Mitchell
ddf45cc758 ppc4xx: Changed 460EX/GT OCM TLB and internal SRAM initialization
Expanded OCM TLB to allow access to 64K OCM as well as 256K of
internal SRAM.

Adjusted internal SRAM initialization to match updated user
manual recommendation.

OCM & ISRAM are now mapped as follows:
        physical        virtual         size
ISRAM   0x4_0000_0000   0xE300_0000     256k
OCM     0x4_0004_0000   0xE304_0000     64k

A single TLB was used for this mapping.

Signed-off-by: Dave Mitchell <dmitch71@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-21 11:02:04 +01:00
Dave Mitchell
b14ca4b61a ppc4xx: Added ppc4xx-isram.h for internal SRAM and L2 cache DCRs
Added include/asm-ppc/ppc4xx-isram.h and moved internal SRAM and
L2 cache DCRs from ppc440.h to this new header.

Also converted these DCR defines from lowercase to uppercase and
modified referencing modules to use them.

Signed-off-by: Dave Mitchell <dmitch71@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-21 10:52:33 +01:00
Selvamuthukumar
9b827cf172 Align end of bss by 4 bytes
Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.

Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-11-18 23:13:16 +01:00
Wolfgang Denk
3cbd823116 Coding Style cleanup, update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-11-02 16:14:22 +01:00
Wolfgang Denk
06c2942218 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2008-10-21 21:19:35 +02:00
Stefan Roese
f4d14c5550 ppc4xx: Add 1.0 & 1.066 GHz to canyonlands bootstrap command for PLL setup
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21 17:35:02 +02:00
Adam Graham
f09f09d389 ppc4xx: Add AMCC Arches board support (dual 460GT)
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR
FLASH, UART, EEPROM and temperature sensor, along with a shared debug
port. The two 460GT's will communicate with each other via shared
memory, Gigabit Ethernet and x1 PCI-Express.

Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21 17:34:46 +02:00
Wolfgang Denk
8ed44d91c8 Cleanup: fix "MHz" spelling
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-10-21 11:25:39 +02:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Stefan Roese
8fd4166c46 ppc4xx: Canyonlands: Remove unnecessary FDT warning upon DTB fixup
Depending on the configuration jumper "SATA SELECT", U-Boot disabled
either one PCIe node or the SATA node in the device tree blob. This
patch removes the unnecessary and even confusing warning, when the node
is not found at all.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-22 23:17:31 +02:00
Wolfgang Denk
afbc526336 Merge branch 'Makefile-next' of git://git.denx.de/u-boot-arm 2008-09-12 16:13:12 +02:00
Stefan Roese
7bf5ecfa50 ppc4xx: Fix SDRAM inititialization of multiple 405 based board ports
This patch fixes a problem introdiced with patch
bbeff30c [ppc4xx: Remove superfluous dram_init() call or replace it by
initdram()].

The boards affected are:
- PCI405
- PPChameleonEVB
- quad100hd
- taihu
- zeus

Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-12 07:12:33 +02:00
Jean-Christophe PLAGNIOL-VILLARD
0e8d158664 rename CFG_ENV macros to CONFIG_ENV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:06 +02:00
Jean-Christophe PLAGNIOL-VILLARD
8a40fb148e move cmd_get_data_size to command.c
add CMD_DATA_SIZE macro to enable it

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:05 +02:00
Jean-Christophe PLAGNIOL-VILLARD
5a1aceb068 rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
0cf4fd3cf8 rename environment.c in env_embedded.c to reflect is functionality
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:01 +02:00
Ben Warren
10efa024b8 Moved initialization of EEPRO100 Ethernet controller to board_eth_init()
Affected boards:
	db64360
	db64460
	katmai
	taihu
	taishan
	yucca
	cpc45
	cpu87
	eXalion
	elppc
	debris
	kvme080
	mpc8315erdb
	integratorap
	ixdp425
	oxc
	pm826
	pm828
	pm854
	pm856
	ppmc7xx
	sc3
	sc520_spunk
	sorcery
	tqm8272
	tqm85xx
	utx8245

Removed initialization of the driver from net/eth.c
Also, wrapped contents of pci_eth_init() by CONFIG_PCI.

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02 21:18:19 -07:00
Stefan Roese
9939ffd5fb Merge branch 'master' of /home/stefan/git/u-boot/u-boot into next 2008-08-12 20:39:27 +02:00
Steven A. Falco
eab1007334 ppc4xx: Sequoia has two UARTs in "4-pin" mode. Configure the GPIOs as per schematic.
The Sequoia board has two UARTs in "4-pin" mode. This patch modifies the GPIO
configuration to match the schematic, and also sets the SDR0_PFC1 register to
select the corresponding mode for the UARTs.

Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-07 12:06:18 +02:00
Stefan Roese
4b326101d6 Merge branch 'master' of /home/stefan/git/u-boot/u-boot into next 2008-07-14 10:45:47 +02:00
Stefan Roese
068c1b77c8 ppc4xx: Remove redundant ft_board_setup() functions from some 4xx boards
This patch removes some ft_board_setup() functions from some 4xx boards.
This can be done since we now have a default weak implementation for this
in cpu/ppc4xx/fdt.c. Only board in need for a different/custom
implementation like canyonlands need their own version.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-13 15:04:11 +02:00
Wolfgang Denk
bde6358762 Fix some more printf() format issues.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-11 22:56:11 +02:00
Stefan Roese
1d0554736a ppc4xx: Some Rewood cleanups (coding style, leading white spaces)
Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-11 13:18:14 +02:00
Stefan Roese
d9056b7913 ppc4xx: Cleanup Katmai & Yucca PCIe register usage
This patch cleans up the 440SPe PCIe register usage. Now only defines
from the include/asm-ppc/4xx_pcie.h are used.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-11 13:18:14 +02:00
Stefan Roese
5de851403b ppc4xx: Rework 440GX UIC handling
This patch reworks the 440GX interrupt handling so that the common 4xx
code can be used. The 440GX is an exception to all other 4xx variants
by having the cascading interrupt vectors not on UIC0 but on a special
UIC named UICB0 (UIC Base 0). With this patch now, U-Boot references
the 440GX UICB0 when UIC0 is selected. And the common 4xx interrupt
handling is simpler without any 440GX special cases.

Also some additional cleanup to cpu/ppc4xx/interrupt.c is done.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-11 13:18:14 +02:00
Stefan Roese
d1631fe1a0 ppc4xx: Consolidate PPC4xx UIC defines
This 2nd patch now removes all UIC mask bit definition. They should be
generated from the vectors by using the UIC_MASK() macro from now on.
This way only the vectors need to get defined for new PPC's.

Also only the really used interrupt vectors are now defined. This makes
definitions for new PPC versions easier and less error prone.

Another part of this patch is that the 4xx emac driver got a little
cleanup, since now the usage of the interrupts is clearer.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-11 13:18:14 +02:00
Stefan Roese
4fb25a3db3 ppc4xx: Consolidate PPC4xx UIC defines
This patch is the first step to consolidate the UIC related defines in the
4xx headers. Move header from asm-ppc/ppc4xx-intvec.h to
asm-ppc/ppc4xx-uic.h as it will hold all UIC related defines in the next
steps.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-11 13:18:13 +02:00
Stefan Roese
e321801bed ppc4xx: Remove redundant ft_board_setup() functions from some 4xx boards
This patch removes some ft_board_setup() functions from some 4xx boards.
This can be done since we now have a default weak implementation for this
in cpu/ppc4xx/fdt.c. Only board in need for a different/custom
implementation like canyonlands need their own version.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-11 13:18:13 +02:00
Feng Kan
0ce5c8675b ppc4xx: Initial framework of the AMCC PPC460SX redwood reference board.
Add AMCC Redwood reference board that uses the latest
PPC 464 CPU processor combined with a rich mix of peripheral
controllers. The board will support PCIe, mutiple Gig ethernet
ports, advanced hardware RAID assistance and IEEE 1588.

Signed-off-by: Feng Kan <fkan@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-11 13:18:12 +02:00
Stefan Roese
b002144e1d ppc4xx: Fix printf format warnings now visible with the updated format check
This patch fixes ppc4xx related printf format warning. Those warnings are
now visible since patch dc4b0b38d4
[Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is
really helpful.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-10 09:58:06 +02:00
Wolfgang Denk
322ef5e28d Cleanup: remove redundant deleting on *~ files
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-02 23:53:23 +02:00
Wolfgang Denk
c8a3b109f0 Cleanup out-or-tree building for some boards (.depend)
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-02 23:49:18 +02:00
Stefan Roese
212ed90615 ppc4xx: Canyonlands: Disable the RTC M41T62 square wave output
This patch disables the square wave output of the M41T62 RTC used on
Canyonlands & Glacier. Here the explanation:

The serial real-time clock part used in the design is an
STMicro M41T62. This part has a full-time 32KHz square wave
output that is connected to the TmrClk input to the
processor. The default state for this square wave output is
enabled so the output runs continuously when the board is
powered normally and also from the battery. The TmrClk input
to the processor goes to ground when the power is removed
from the board/processor, and therefore the running square
wave output is driving ground which drains the battery quickly.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-12 15:50:31 +02:00
Becky Bruce
9973e3c614 Change initdram() return type to phys_size_t
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory.  phys_size_t is defined as an unsigned long on almost
all current platforms.

This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram).  It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.

Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-12 08:50:18 +02:00
Wolfgang Denk
1730edf76c Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xx 2008-06-11 22:13:07 +02:00
Stefan Roese
72675dc6c0 ppc4xx: Unify AMCC's board config files (part 3/3)
This patch series unifies the AMCC eval board ports by introducing
a common include header for all AMCC eval boards:

include/configs/amcc-common.h

This header now includes all common configuration options/defines which
are removed from the board specific headers.

The reason for this is ease of maintenance and unified look and feel
of all AMCC boards.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-06 15:55:21 +02:00
Haavard Skinnemoen
d255bb0e78 SPI API improvements
This patch gets rid of the spi_chipsel table and adds a handful of new
functions that makes the SPI layer cleaner and more flexible.

Instead of the spi_chipsel table, each board that wants to use SPI
gets to implement three hooks:
  * spi_cs_activate(): Activates the chipselect for a given slave
  * spi_cs_deactivate(): Deactivates the chipselect for a given slave
  * spi_cs_is_valid(): Determines if the given bus/chipselect
    combination can be activated.

Not all drivers may need those extra functions however. If that's the
case, the board code may just leave them out (assuming they know what
the driver needs) or rely on the linker to strip them out (assuming
--gc-sections is being used.)

To set up communication parameters for a given slave, the driver needs
to call spi_setup_slave(). This returns a pointer to an opaque
spi_slave struct which must be passed as a parameter to subsequent SPI
calls. This struct can be freed by calling spi_free_slave(), but most
driver probably don't want to do this.

Before starting one or more SPI transfers, the driver must call
spi_claim_bus() to gain exclusive access to the SPI bus and initialize
the hardware. When all transfers are done, the driver must call
spi_release_bus() to make the bus available to others, and possibly
shut down the SPI controller hardware.

spi_xfer() behaves mostly the same as before, but it now takes a
spi_slave parameter instead of a spi_chipsel function pointer. It also
got a new parameter, flags, which is used to specify chip select
behaviour. This may be extended with other flags in the future.

This patch has been build-tested on all powerpc and arm boards
involved. I have not tested NIOS since I don't have a toolchain for it
installed, so I expect some breakage there even though I've tried
fixing up everything I could find by visual inspection.

I have run-time tested this on AVR32 ATNGW100 using the atmel_spi and
DataFlash drivers posted as a follow-up. I'd like some help testing
other boards that use the existing SPI API.

But most of all, I'd like some comments on the new API. Is this stuff
usable for everyone? If not, why?

Changed in v4:
  - Build fixes for various boards, drivers and commands
  - Provide common struct spi_slave definition that can be extended by
    drivers
  - Pass a struct spi_slave * to spi_cs_activate and spi_cs_deactivate
  - Make default bus and mode build-time configurable
  - Override default SPI bus ID and mode on mx32ads and imx31_litekit.

Changed in v3:
  - Add opaque struct spi_slave for controller-specific data associated
    with a slave.
  - Add spi_claim_bus() and spi_release_bus()
  - Add spi_free_slave()
  - spi_setup() is now called spi_setup_slave() and returns a
    struct spi_slave
  - soft_spi now supports four SPI modes (CPOL|CPHA)
  - Add bus parameter to spi_setup_slave()
  - Convert the new i.MX32 SPI driver
  - Convert the new MC13783 RTC driver

Changed in v2:
  - Convert the mpc8xxx_spi driver and the mpc8349emds board to the
    new API.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Tested-by: Guennadi Liakhovetski <lg@denx.de>
2008-06-03 20:28:50 +02:00
Stefan Roese
3c1de1a6d3 ppc4xx: Remove implementations of testdram()
This patch removes the used testdram() implementations of the board
that are maintained by myself.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:24 +02:00
Stefan Roese
bbeff30cbd ppc4xx: Remove superfluous dram_init() call or replace it by initdram()
Historically the 405 U-Boot port had a dram_init() call in early init
stage. This function was still called from start.S and most of the time
coded in assembler. This is not needed anymore (since a long time) and
boards should implement the common initdram() function in C instead.

This patch now removed the dram_init() call from start.S and removes the
empty implementations that are scattered through most of the 405 board
ports. Some older board ports really implement this dram_init() though.
These are:

csb272
csb472
ERIC
EXBITGEN
W7OLMC
W7OLMG

I changed those boards to call this assembler dram_init() function now
from their board specific initdram() instead. This *should* work, but please
test again on those platforms. And it is perhaps a good idea that those
boards use some common 405 SDRAM initialization code from cpu/ppc4xx at
some time. So further patches welcome here.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:19 +02:00
Stefan Roese
ec724f883e ppc4xx: Change Kilauea to use the common DDR2 init function
This patch changes the kilauea and kilauea_nand (for NAND booting)
board port to not use a board specific DDR2 init routine anymore. Now
the common code from cpu/ppc4xx is used.

Thanks to Grant Erickson for all his basic work on this 405EX early
bootup.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:03 +02:00
Grant Erickson
8a24c07ba5 ppc4xx: Enable Primordial Stack for 40x and Unify ECC Handling
This patch (Part 2 of 2):

* Rolls up a suite of changes to enable correct primordial stack and
  global data handling when the data cache is used for such a purpose
  for PPC40x-variants (i.e. CFG_INIT_DCACHE_CS).

* Related to the first, unifies DDR2 SDRAM and ECC initialization by
  eliminating redundant ECC initialization implementations and moving
  redundant SDRAM initialization out of board code into shared 4xx
  code.

* Enables MCSR visibility on the 405EX(r).

* Enables the use of the data cache for initial RAM on
  both AMCC's Kilauea and Makalu and removes a redundant
  CFG_POST_MEMORY flag from each board's CONFIG_POST value.

  - Removed, per Stefan Roese's request, defunct memory.c file for
    Makalu and rolled sdram_init from it into makalu.c.

With respect to the 4xx DDR initialization and ECC unification, there
is certainly more work that can and should be done (file renaming,
etc.). However, that can be handled at a later date on a second or
third pass. As it stands, this patch moves things forward in an
incremental yet positive way for those platforms that utilize this
code and the features associated with it.

Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:21:20 +02:00
Wolfgang Denk
53677ef18e Big white-space cleanup.
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-21 00:14:08 +02:00
Stefan Roese
16bedc661d ppc4xx: Canyonlands: Disable PCIe0/SATA in dev-tree depending on selection
When SATA is selected (via jumper J6) we need to disable the first PCIe
node in the device tree, so that Linux doesn't initialize it. Otherwise
the Linux SATA driver will fail to detect the devices.

The same goes the other way around too. So if PCIe is selected we need
to disable the SATA node in the device tree.

This is because PCIe port 0 and SATA on 460EX share the same pins
(multiplexed) and we have to configure in U-Boot which peripheral is
enabled.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-05-19 07:14:38 +02:00
Stefan Roese
2dd7082e06 ppc4xx: Fix bogus Canyonlands config.mk
This patch fixes the canyonlands config.mk file to enable correct
out-of-tree builds. Thanks to Wolfgang Denk for spotting this.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-05-14 13:40:03 +02:00
Stefan Roese
70fab1908f ppc4xx: Add 405EX(r) revision C PVR definitions and detection code
Signed-off-by: Stefan Roese <sr@denx.de>
2008-05-13 20:22:01 +02:00
Stefan Roese
d1c1ba85c7 ppc4xx: acadia: Add fdt support and fix section overlap problem
This patch adds fdt (flattened device tree) support to the AMCC
Acadia eval board. This increases the image size and it doesn't
fit anymore into 256kByte. Since we didn't want to remove features
from the configuration, we decided to increase the U-Boot image size
(add one flash sector).

Also changed the default environment definition to make it
independent of such changes.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-05-08 10:48:58 +02:00
Ira Snyder
4adb3023de ppc4xx: Add device tree support to AMCC Yosemite
Add support for booting with a device tree blob. This is needed to boot
ARCH=powerpc kernels. Also add support for setting the eth0 mac address
via the ethaddr variable.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-05-08 07:06:05 +02:00
Wolfgang Denk
941d696d25 katmai: fix section overlap problem
Since we didn't want to remove features from the configuration, we
decided to increase the U-Boot image size (add one flash sector).

Also changed the default environment definition to make it
independent of such changes.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2008-04-28 11:00:14 +02:00
Stefan Roese
499e7831e1 ppc4xx: Change Canyonlands to support booting from 2k page NAND devices
Signed-off-by: Stefan Roese <sr@denx.de>
2008-04-18 16:30:49 +02:00
Jason Wessel
3d36be0300 Remove all the search paths from the .lds files.
The cross compiler is responsible for providing the correct libraries
and the logic to find the linking libraries.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
2008-04-17 23:57:32 -07:00
Stefan Roese
1c2926abdd ppc4xx: Canyonlands: Init SATA/PCIe port correctly
Canyonlands (460EX) shares the first PCIe interface with the SoC SATA
interface. This usage can be configured with the jumper J6. This patch
correctly configures the SATA/PCIe PHY for SATA usage when this jumper
is installed.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-04-02 08:39:33 +02:00
Stefan Roese
cc8e839abc ppc4xx: Canyonlands: Print SATA/PCIe configuration and board revision
Canyonlands (460EX) shares the first PCIe interface with the SoC SATA
interface. This usage can be configured with the jumper J6. This patch
displays the current configuration upon bootup and changes the PCIe
init loop, to only initialize the availabel PCIe slots.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-28 14:09:04 +01:00
Stefan Roese
c664bf8c3c ppc4xx: Fix Canyonlands linker script (remove bogus ASSERT)
Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-27 10:09:05 +01:00
Stefan Roese
d56a3ce179 ppc4xx: Correctly pass phyiscal FLASH base address into dtb
The routine ft_board_setup() configures the EBC NOR mappings for the
Linux physmap_of driver. Since on 460EX/GT we remap the FLASH from
0x4.fc00.0000 to 0x4.cc00.0000 because of the max. 16MByte boot-CS
problem, we need to pass the corrected address here too.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-27 09:54:41 +01:00
Stefan Roese
4c9e855734 ppc4xx: Add AMCC Glacier 406GT eval board support
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:

- 4 ethernet ports instead of 2
- no SATA port
- no USB port

Currently EMAC2+3 are not working. This will be fixed in a later
release.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-27 09:54:41 +01:00
Stefan Roese
41712b4e8c ppc4xx: Add USB OHCI support to AMCC Canyonlands 460EX eval board
This patch adds USB OHCI support to the Canyonlands board port. It also
enables EXT2 support.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:28:05 +01:00
Stefan Roese
71665ebf88 ppc4xx: Add Canyonlands NAND booting support
460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.

This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.

Tested with 512 byte page NAND device (32MByte) on Canyonlands.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:28:05 +01:00
Stefan Roese
8e1a3fe545 ppc4xx: Add AMCC Canyonlands support (460EX) (1/3)
This patch adds support for the AMCC Canyonlands 460EX evaluation
board.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:28:04 +01:00
Stefan Roese
e4170e5a50 ppc4xx: Fix comment in 405EX DDR2 init code
Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-15 07:22:15 +01:00
Markus Brunner
772003e439 fix taihu soft spi_read
The taihu board used gpio_read_out_bit which reads the output register and not
the pin state.

Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
2008-03-07 09:15:26 +01:00
Stefan Roese
64cd594e62 ppc4xx: Fix acadia_nand build problem
Don't include testdram() on NAND-booting target acadia_nand. This saves
a few bytes and makes the target build clean again.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-02-25 16:50:48 +01:00
Mike Nuss
b738654d3c PPC440EPx: Optionally enable second I2C bus
The option CONFIG_I2C_MULTI_BUS does not have any effect on Sequoia, the
PPC440EPx reference platform, because IIC1 is never enabled. Add Sequoia board
code to turn on IIC1 if CONFIG_I2C_MULTI_BUS is selected.

Signed-off-by: Mike Nuss <mike@terascala.com>
Cc: Stefan Roese <sr@denx.de>
2008-02-16 07:00:03 +01:00
Wolfgang Denk
865f0f9754 Coding Style Cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-23 14:31:17 +01:00
Stefan Roese
be88b16998 ppc4xx: Fix remaining CONFIG_COMMANDS in 4xx files
Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-17 07:50:17 +01:00
Matthias Fuchs
83a49c8dd7 ppc4xx: Sequoia coding style cleanup and beautification
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-01-16 11:24:28 +01:00
Stefan Roese
a0dd99d51e ppc4xx: Update Kilauea CPLD configuration with USB PHY reset bit
Now that bit 29 is the USB PHY reset bit, update the Kilauea port
to remove the USB PHY reset after powerup. The CPLD will keep the
USB PHY in reset (active low) until the bit is set to 1 in
board_early_init_f().

Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-14 10:05:05 +01:00
Wolfgang Denk
6eb3fb1558 Makalu: fix compile warning
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-13 16:07:44 +01:00
Wolfgang Denk
64134f0112 Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections
With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]

For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.

The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12 20:31:39 +01:00
Stefan Roese
d5a163d6ba ppc4xx: Fix sdram init on Sequoia boards
Clear possible errors in MCSR resulting from data-eye-search.
If not done, then we could get an interrupt later on when
exceptions are enabled.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-11 15:53:58 +01:00
Niklaus Giger
4d332dbeb0 ppc4xx: Make Sequoia boot vxWorks
vxWorks expects in
TLB 0 a entry for the Machine Check interrupt
TLB 1 a entry for the RAM
TLB 2 a entry for the EBC
TLB 3 a entry for the boot flash

After changing the baudrate to 9600 I had no problems to boot the
vxWorks image as distributed by WindRiver (Revision 2.0/1 from
June 18, 2007)

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2008-01-10 19:06:54 +01:00
Matthias Fuchs
1f84021a85 ppc4xx: assign PCI interrupts on seuqoia boards
Some operating systems rely on assigned PCI interrupts.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-01-09 06:33:03 +01:00
Stefan Roese
6399b23d60 Merge branch 'katmai-ddr-gda' 2008-01-05 10:13:40 +01:00
Stefan Roese
845c6c95db ppc4xx: Update Katmai/44x_spd_ddr2.c code for optimal DDR2 setup
On Katmai the complete auto-calibration somehow doesn't seem to
produce the best results, meaning optimal values for RQFD/RFFD.
This was discovered by GDA using a high bandwidth scope,
analyzing the DDR2 signals. GDA provided a fixed value for RQFD,
so now on Katmai "only" RFFD is auto-calibrated.

This patch also adds RDCC calibration as mentioned on page 7 of
the AMCC PowerPC440SP/SPe DDR2 application note:
"DDR1/DDR2 Initialization Sequence and Dynamic Tuning"

Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-05 09:12:41 +01:00
Lawrence R. Johnson
b05e8bf58b ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Sequoia board
Note: this patch changes the configuration of some GPIO registers:

   Register      Old Value   New Value
---------------  ----------  ----------
DCR GPIO0_TCR    0x0000000F  0x0000F0CF
DCR GPIO0_TSRH   0x55005000  0x00000000
DCR GPIO1_TCR    0xC2000000  0xE2000000
DCR GPIO1_TSRL   0x0C000000  0x00200000
DCR GPIO1_ISR2L  0x00050000  0x00110000

Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-04 11:39:05 +01:00
Larry Johnson
62cc3951ab PPC4xx: Remove sdram.h from board/amcc/sequoia
These definitions are now in "include/ppc440.h".

Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-04 11:37:38 +01:00
Larry Johnson
ce3902e176 PPC4xx: Use common code for Sequoia board SDRAM support
Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-04 11:37:33 +01:00
Larry Johnson
c46f53333b Add definitions for 440EPx/GRx SDRAM controller to ppc440.h
This patch adds the Denali SDRAM controller definitions to "ppc440.h".
It also fixes two typos in the definitions, so the board-specific
"sdram.h" files containing these definitions are also fixed to avoid
compiler warnings.

Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27 19:35:36 +01:00
Larry Johnson
d3471173e1 Use out_be32() and friends to access memory-mapped registers in sequoia.c
Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27 19:35:35 +01:00
Larry Johnson
c68f59fe3e Use definitions from "asm-ppc/mmu.h" in init.S for Sequoia
Signed-off-by: Larry Johnson <lrj@acm.org>
2007-12-27 19:35:35 +01:00
Stefan Roese
bf8324e4a5 ppc4xx: Add fdt support to AMCC Katmai eval board
Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27 19:35:34 +01:00
Stefan Roese
136288847e ppc4xx: Bring 4xx fdt support up-to-date
This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27 19:35:32 +01:00
Stefan Roese
7cfc12a7dc ppc4xx: 405EX: Correctly enable USB pins
This patch selects the USB data pins in the 405EX GPIO and MFC (multi
function control) registers. This is done for the AMCC Kilauea and
Makalu eval boards.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-08 14:47:34 +01:00
Stefan Roese
a27044b14a ppc4xx: Enable hardware-fix for PCI/DMA errata on AMCC 440SP/SPe boards
This patch enables the hardware-fix for the PCI/DMA errata's 19+22 by
setting the FIXD bit in the SDR0_MFR register. Here a description of the
symptoms:

Problem Description
------------------------------
If a DMA is performed between memory and PCI with the DMA 1 Controller
using prefetch, and as a result uses a special purpose buffer selected by
the PCIXn Bridge Options 1 Register (PCIXn_BRDGOPT1[RBP7] - bits 31-29),
the first part of the transfer sequence is performed twice. The
PPC440SPe PCI Controller requests more data than was needed such that in
the case of enforce memory protection, a host CPU  exception can occur.
No data is corrupted, because data transfer is stopped in the PCI
Controller. Prefetch enable is specified by setting DMA Configuration
Register (I2O0_DMAx_CFG[DXEPD] - bit 31) to 0.

Behavior that may be observed in a running system
---------------------------------------------------------------------------

1. DMA performance is decreased because of the double access on the PCI bus
interface.
2. If an illegal access to some address on the PCI bus is detected at the
system level, a machine check or similar system error may occur.

Workarounds Available
----------------------------------

1. Do not program prefetch. Note that a prefetch command cannot be programmed
without selecting a special purpose buffer.
2. To avoid crossing a physical boundary of the PCI slave device, add 512
bytes of address to the PCI address range.

This patch was originally provided by Pravin M. Bathija <pbathija@amcc.com>
from AMCC and slighly changed.

Signed-off-by: Pravin M. Bathija <pbathija@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-06 05:58:43 +01:00
Stefan Roese
e15e33433e ppc4xx: Kilauea: Add PCIe reset assertion upon power-up
This manual PCIe reset triggering solves the problem seen with the
Intel EPRO/1000 card, which was not detected (link not established)
upon power-up reset.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-30 07:15:41 +01:00
Stefan Roese
ecdcbd4f8c ppc4xx: Update AMCC Makalu for board rev 1.1
This patch adds changes needed for Makalu rev 1.1:

- Enable 2nd DDR2 bank resulting in 256MByte of SDRAM
- Enable 2nd ethernet port EMAC1
- Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE)
- Reset PCIe ports via GPIO upon bootup

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-16 14:00:59 +01:00
Stefan Roese
c9672f81f1 ppc4xx: Small AMCC Kilauea cleanup
Remove not needed pci_target_init() function.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-15 14:25:09 +01:00
Stefan Roese
654f38b3a3 ppc4xx: Make output a little shorter on PCIe detection
Now not max 3 lines but 2 lines are printed per PCIe port.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-05 07:43:05 +01:00
Stefan Roese
3d6cb3b24a ppc4xx: Add AMCC Kilauea/Haleakala NAND booting support
This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-03 12:08:28 +01:00
Stefan Roese
ea2e142843 ppc4xx: Add CONFIG_4xx_DCACHE compile options to enable cached SDRAM
This patch adds the CONFIG_4xx_DCACHE options to some SDRAM init files
and to the Sequoia TLB init code. Now the cache can be enabled on 44x
boards by defining CONFIG_4xx_DCACHE in the board config file. This
option will disappear, when more boards use is successfully and no
more known problems exist.

This is tested successfully on Sequoia and Katmai. The only problem that
needs to be fixed is, that USB is not working on Sequoia right now, since
it will need some cache handling code too, similar to the 4xx EMAC driver.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:21:47 +01:00
Stefan Roese
353f2688b4 ppc4xx: Add initial AMCC Haleakala PPC405EXr eval board support
The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:51 +01:00
Eugene O'Brien
9f798766aa ppc4xx: Fixed offset of refresh rate type for Bamboo on-board DDR SDRAM
This patch also adds a note to the fixed DDR setup for Bamboo NAND booting:

Note:
As found out by Eugene O'Brien <eugene.obrien@advantechamt.com>, the fixed
DDR setup has problems (U-Boot crashes randomly upon TFTP), when the DIMM
modules are still plugged in. So it is recommended to remove the DIMM
modules while using the NAND booting code with the fixed SDRAM setup!

Signed-off-by: Eugene O'Brien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:51 +01:00
Stefan Roese
882ae41274 ppc4xx: Rework of 4xx serial driver (2)
Change all linker scripts to reference the changed driver name 4xx_uart.o.

Note: In most cased all these explicit referencing of these object files
in the linker scripts is not neccessary. Only for manually embedded
environment into the U-Boot image, which is not done is most cases.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:51 +01:00
Stefan Roese
211ea91ac6 ppc4xx: Add initial AMCC Makalu 405EX support
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:50 +01:00
Stefan Roese
087dfdb79b ppc4xx: Consolidate some of the 405 and 440 macros/structs into 4xx
This patch moves some common 4xx macros and the PPC405_SYS_INFO/
PPC440_SYS_INFO structure into the common ppc4xx.h header.

Lot's of other macros are good candidates to be consolidated this way
in the future.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:50 +01:00
Stefan Roese
770c7af580 ppc4xx: Fix size setup in Kilauea DDR2 init routine
The size was initilized wrong. Instead of 256MB, the DDR2 controller
was setup to 512MB. Now the correct values is used.

This patch also does a little cleanup and adds a comment here.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:50 +01:00
Stefan Roese
d4cb2d1794 ppc4xx: Dynamic configuration of 4xx PCIe mode as root or endpoint mode
This patch adds support for dynamic configuration of PCIe ports for the
AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe
boards Yucca & Katmai and the 405EX board Kilauea.

This dynamic configuration is done via the "pcie_mode" environement
variable. This variable can be set to "EP" or "RP" for endpoint or
rootpoint mode. Multiple values can be joined via the ":" delimiter.
Here an example:

pcie_mode=RP:EP:EP

This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2
as endpoint.

Per default Yucca will be configured as:
pcie_mode=RP:EP:EP

Per default Katmai will be configured as:
pcie_mode=RP:RP:REP

Per default Kilauea will be configured as:
pcie_mode=RP:RP

Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:50 +01:00
Stefan Roese
fd671802b6 ppc4xx: Enable device tree support (fdt) on Kilauea per default
This patch enables the fdt support on the AMCC Kilauea eval board.
Additionally now EBC ranges fdt fixup is included to support NOR
FLASH mapping via the Linux physmap_of driver.

This Kilauea port now support booting arch/ppc and arch/powerpc
Linux kernels. The default environment "net_nfs" is for arch/ppc
and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc
support will be removed.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:50 +01:00
Stefan Roese
566806ca1a ppc4xx: Add initial AMCC Kilauea 405EX support
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:49 +01:00
Stefan Roese
026f711068 ppc4xx: Make 440SPe PCIe code more generic to use on different 4xx PPCs (2)
This patch is the first patch of a series to make the 440SPe PCIe code
usable on different 4xx PPC platforms. In preperation for the new 405EX
which is also equipped with PCIe interfaces.

(2) This patch renames the functions from 440spe_ to 4xx_ with a
    little additional cleanup

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:49 +01:00
Stefan Roese
c7c6da2302 ppc4xx: Make 440SPe PCIe code more generic to use on different 4xx PPCs (1)
This patch is the first patch of a series to make the 440SPe PCIe code
usable on different 4xx PPC platforms. In preperation for the new 405EX
which is also equipped with PCIe interfaces.

(1) This patch renames the files from 440spe_pcie to 4xx_pcie

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:48 +01:00
Stefan Roese
3e11ae80fe ppc4xx: Add 667/133 (CPU/PLB) frequency setup to Sequoia bootstrap command
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-18 07:44:56 +02:00
Stefan Roese
e2e93442e5 ppc4xx: Fix bug in I2C bootstrap values for Sequoia/Rainier
The I2C bootstrap values that can be setup via the "bootstrap" command,
were setup incorrect regarding the generation of the internal sync PCI
clock. The values for PLB clock == 133MHz were slighly incorrect and the
values for PLB clock == 166MHz were totally incorrect. This could
lead to a hangup upon booting while PCI configuration scan.

This patch fixes this issue and configures valid PCI divisor values
for the sync PCI clock, with respect to the provided external async
PCI frequency.

Here the values of the formula in the chapter 14.2 "PCI clocking"
from the 440EPx users manual:

AsyncPCICLK - 1MHz <= SyncPCIClk <= (2 * AsyncPCIClk) - 1MHz

33MHz async PCI frequency:
PLB = 133:
=>      32 <= 44.3 <= 65        (div = 3)

PLB = 166:
=>      32 <= 55.3 <= 65        (div = 3)

66MHz async PCI frequency:
PLB = 133:
=>      65 <= 66.5 <= 132       (div = 2)

PLB = 166:
=>      65 <= 83 <= 132         (div = 2)

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-15 11:39:00 +02:00
Stefan Roese
5a5958b7de ppc4xx: Fix incorrect 33/66MHz PCI clock log-message on Sequoia & Yosemite
The BCSR status bit for the 66MHz PCI operation was correctly
addressed (MSB/LSB problem). Now the correct currently setup
PCI frequency is displayed upon bootup.

This patch also fixes this problem on Rainier & Yellowstone, since these
boards use the same souce code as Sequoia & Yosemite do.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-15 11:29:33 +02:00
Stefan Roese
738815c0cc ppc4xx: Coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-02 11:44:46 +02:00
Grzegorz Bernacki
2db6478406 Program EPLD to force full duplex mode for PHY.
EPLD forces modes of PHY operation. By default full duplex is turned off.
This fix turns it on.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2007-10-02 11:30:37 +02:00
Wolfgang Denk
1218abf1b5 Fix cases where DECLARE_GLOBAL_DATA_PTR was not declared as global
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-09-15 20:48:41 +02:00
Grzegorz Bernacki
6efc1fc0b6 [PPC440SPe] PCIe environment settings for Katmai and Yucca
- 'pciconfighost' is set by default in order to be able to scan bridges
behind the primary host/PCIe

- 'pciscandelay' env variable is recognized to allow for user-controlled
delay before the PCIe bus enumeration; some peripheral devices require a
significant delay before they can be scanned (e.g. LSI8408E); without the
delay they are not detected

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2007-09-07 18:35:37 +02:00
Grzegorz Bernacki
7f19139389 [PPC440SPe] Improve PCIe configuration space access
- correct configuration space mapping
- correct bus numbering
- better access to config space

Prior to this patch, the 440SPe host/PCIe bridge was able to configure only the
first device on the first bus. We now allow to configure up to 16 buses;
also, scanning for devices behind the PCIe-PCIe bridge is supported, so
peripheral devices farther in hierarchy can be identified.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
2007-09-07 18:20:23 +02:00
Gary Jennejohn
81b73dec16 ppc4xx: (Re-)Enable CONFIG_PCI_PNP on AMCC 440EPx Sequoia
The 440EPx has a problem when the PCI_CACHE_LINE_SIZE register is
set to non-zero, because it doesn't support MRM (memory-read-
multiple) correctly. We now added the possibility to configure
this register in the board config file, so that the default value
of 8 can be overridden.

Here the details of this patch:

o drivers_pci_auto.c: introduce CFG_PCI_CACHE_LINE_SIZE to allow
  board-specific settings. As an example the sequoia board requires 0.
  Idea from Stefan Roese <sr@denx.de>.
o board/amcc/sequoia/init.S: add a TLB mapping at 0xE8000000 for the
  PCI IO-space. Obtained from Stefan Roese <sr@denx.de>.
o include/configs/sequoia.h: turn CONFIG_PCI_PNP back on and set
  CFG_PCI_CACHE_LINE_SIZE to 0.

Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-31 15:21:46 +02:00
Stefan Roese
02ba7022f6 ppc4xx: Update Sequoia/Rainier bootstrap command
As suggested by David Mitchell, here an update for the Sequoia/Rainier
bootstrap command.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-16 09:52:29 +02:00
Stefan Roese
34886bbea2 Merge with /home/stefan/git/u-boot/zeus 2007-08-14 15:00:42 +02:00
Stefan Roese
779e975117 ppc4xx: Add initial Zeus (PPC405EP) board support
Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-14 14:44:41 +02:00
Eugene OBrien
d2f6800662 ppc4xx: Update AMCC Bamboo 440EP support
Changed storage type of cfg_simulate_spd_eeprom to const
Changed storage type of gpio_tab to stack storage
(Cannot access global data declarations in .bss until afer code relocation)

Improved SDRAM tests to catch problems where data is not uniquely addressable
(e.g. incorrectly programmed SDRAM row or columns)

Added CONFIG_PROG_SDRAM_TLB to support Bamboo SIMM/DIMM modules
Fixed AM29LV320DT (OpCode Flash) sector map

Signed-off-by: Eugene OBrien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-07-31 10:24:56 +02:00
John Otken
d4024bb72d ppc4xx: Add support for AMCC 405EP Taihu board
Signed-off-by: John Otken <john@softadvances.com>
2007-07-26 17:49:11 +02:00
Stefan Roese
2a49fc17d0 ppc4xx: AMCC Luan uses the new boardspecific DDR2 controller setup
Signed-off-by: Stefan Roese <sr@denx.de>
2007-07-16 10:01:38 +02:00
Stefan Roese
df3f17422a ppc4xx: Support for Yucca board with 440SPe Rev A added to 44x_spd_ddr2.c
The new boardspecific DDR2 controller configuration is used for the Yucca
board. Now the Yucca board with 440SPe Rev. A chips is also supported.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-07-16 10:00:43 +02:00
Niklaus Giger
f780b83316 resubmit: ppc4xx: Remove sequoia/sequioa.h. Cleanup ppc440.h for PPC440EPX
Signed-off-by: Niklaus Giger <niklaus.giger@nestal.com>
2007-07-04 10:14:07 +02:00
Stefan Roese
e4feb7638c Merge with git://www.denx.de/git/u-boot.git 2007-06-25 20:20:30 +02:00
Stefan Roese
466fff1a7b ppc4xx: Add pci_pre_init() for 405 boards
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-25 15:57:39 +02:00
Wolfgang Denk
1636d1c852 Coding stylke cleanup; rebuild CHANGELOG 2007-06-22 23:59:00 +02:00
Igor Lisitsin
a11e06965e Extend POST support for PPC440
Added memory, CPU, UART, I2C and SPR POST tests for PPC440.

Signed-off-by: Igor Lisitsin <igor@emcraft.com>
--
2007-06-22 23:21:01 +02:00
Stefan Roese
b3f9ec86e3 ppc4xx: Add bootstrap command for AMCC Sequoia (440EPx) eval board
This patch adds a board command to configure the I2C bootstrap EEPROM
values. Right now 533 and 667MHz are supported for booting either via NOR
or NAND FLASH. Here the usage:

=> bootstrap 533 nor        ;to configure the board for 533MHz NOR booting
=> bootstrap 667 nand       ;to configure the board for 667MHz NNAND booting

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-19 17:22:44 +02:00
Stefan Roese
df8a24cdd3 [ppc4xx] Fix problem with NAND booting on AMCC Acadia
The latest changes showed a problem with the location of the NAND-SPL
image in the OCM and the init-data area (incl. cache). This patch
fixes this problem.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-19 16:42:31 +02:00
Stefan Roese
86ba99e341 [ppc4xx] Change board/amcc/acadia/cpr.c to pll.c
Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-19 16:40:58 +02:00
Stefan Roese
c440bfe6d6 ppc4xx: Add NAND booting support for AMCC Acadia (405EZ) eval board
This patch adds NAND booting support for the AMCC Acadia eval board.

Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.

I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:

=> bootstrap 267 nor	;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand	;to configure the board for 267MHz NNAND booting

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-06 11:42:13 +02:00
Stefan Roese
18d156eb37 ppc4xx: Add missing file for Bamboo NAND booting support
Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01 16:18:17 +02:00
Stefan Roese
f3679aa13d Merge with /home/stefan/git/u-boot/bamboo-nand 2007-06-01 16:15:34 +02:00
Stefan Roese
155a96478a ppc4xx: Undo Sequoia patch for dynamic EBC speed support of 83MHz
This patch undoes the patch by Jeff Mann with commit-id ada4697d. As
suggested by AMCC it is not recommended to dynamically change the EBC
speed after bootup. So we undo this change to be on the safe side.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01 15:58:19 +02:00
Stefan Roese
9d9096043e ppc4xx: Update Sequoia NAND booting support with ECC
Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01 15:29:04 +02:00