Commit graph

54 commits

Author SHA1 Message Date
Stefan Roese
9a929170be ppc4xx: Disable POST memory test on NAND-booting Sequoia
Don't run the memory POST on the NAND-booting version. It will
overwrite part of the U-Boot image which is already loaded from NAND
to SDRAM. We were just lucky that it booted at all with this SDRAM
test enabled.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-04-16 09:12:08 +02:00
Wolfgang Grandegger
6c869637fe NAND: rename NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define

 #define NAND_MAX_CHIPS          CONFIG_SYS_MAX_NAND_DEVICE

but that's bogus and did not work anyhow.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:51 -06:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Peter Tyser
abbb90666d Remove unused CFG_EEPROM_PAGE_WRITE_ENABLE references
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-10-14 14:45:31 +02:00
Jean-Christophe PLAGNIOL-VILLARD
0e8d158664 rename CFG_ENV macros to CONFIG_ENV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:06 +02:00
Jean-Christophe PLAGNIOL-VILLARD
5a1aceb068 rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
51bfee1920 rename CFG_ENV_IS_IN_NAND in CONFIG_ENV_IS_IN_NAND
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:58 +02:00
Stefan Roese
3d4a746e2f ppc4xx: Increase image size for NAND boot target
This is needed since now with HUSH enabled (amcc-common.h) the image
read from NAND exceeds the previous limit.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-30 11:24:44 +02:00
Jean-Christophe PLAGNIOL-VILLARD
00b1883a4c drivers/mtd: Move conditional compilation to Makefile
rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:42 +02:00
Steven A. Falco
eab1007334 ppc4xx: Sequoia has two UARTs in "4-pin" mode. Configure the GPIOs as per schematic.
The Sequoia board has two UARTs in "4-pin" mode. This patch modifies the GPIO
configuration to match the schematic, and also sets the SDR0_PFC1 register to
select the corresponding mode for the UARTs.

Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-07 12:06:18 +02:00
Stefan Roese
72675dc6c0 ppc4xx: Unify AMCC's board config files (part 3/3)
This patch series unifies the AMCC eval board ports by introducing
a common include header for all AMCC eval boards:

include/configs/amcc-common.h

This header now includes all common configuration options/defines which
are removed from the board specific headers.

The reason for this is ease of maintenance and unified look and feel
of all AMCC boards.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-06 15:55:21 +02:00
Wolfgang Denk
53677ef18e Big white-space cleanup.
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-21 00:14:08 +02:00
Stefan Roese
14f73ca679 ppc: Add CFG_MEM_TOP_HIDE option to hide memory area that doesn't get "touched"
If CFG_MEM_TOP_HIDE is defined in the board config header, this specified
memory area will get subtracted from the top (end) of ram and won't get
"touched" at all by U-Boot. By fixing up gd->ram_size the Linux kernel
should gets passed the now "corrected" memory size and won't touch it
either. This should work for arch/ppc and arch/powerpc. Only Linux board
ports in arch/powerpc with bootwrapper support, which recalculate the
memory size from the SDRAM controller setup, will have to get fixed
in Linux additionally.

This patch enables this config option on some PPC440EPx boards as a workaround
for the CHIP 11 errata. Here the description from the AMCC documentation:

CHIP_11: End of memory range area restricted access.
Category: 3

Overview:
The 440EPx DDR controller does not acknowledge any
transaction which is determined to be crossing over the
end-of-memory-range boundary, even if the starting address is
within valid memory space. Any such transaction from any PLB4
master will result in a PLB time-out on PLB4 bus.

Impact:
In case of such misaligned bursts, PLB4 masters will not
retrieve any data at all, just the available data up to the
end of memory, especially the 440 CPU. For example, if a CPU
instruction required an operand located in memory within the
last 7 words of memory, the DCU master would burst read 8
words to update the data cache and cross over the
end-of-memory-range boundary. Such a DCU read would not be
answered by the DDR controller, resulting in a PLB4 time-out
and ultimately in a Machine Check interrupt. The data would
be inaccessible to the CPU.

Workaround:
Forbid any application to access the last 256 bytes of DDR
memory. For example, make your operating system believe that
the last 256 bytes of DDR memory are absent. AMCC has a patch
that does this, available for Linux.

This patch sets CFG_MEM_TOP_HIDE for the following 440EPx boards:
lwmon5, korat, sequoia

The other remaining 440EPx board were intentionally not included
since it is not clear to me, if they use the end of ram for some
other purpose. This is unclear, since these boards have CONFIG_PRAM
defined and even comments like this:

PMC440.h:
/* esd expects pram at end of physical memory.
 * So no logbuffer at the moment.
 */

It is strongly recommended to not use the last 256 bytes on those
boards too. Patches from the board maintainers are welcome.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-27 10:12:07 +01:00
Stefan Roese
fc84a8495a ppc4xx: Sequoia: Add device tree (fdt) Linux booting default env variables
Signed-off-by: Stefan Roese <sr@denx.de>
2008-03-07 08:01:43 +01:00
Detlev Zundel
d8ab58b212 Replace "run load; run update" with conditionalized "run load update".
The latter version stops when "run load" fails for whatever reasons
rendering the combination *a lot* more secure.

Signed-off-by: Detlev Zundel <dzu@denx.de>
2008-03-06 17:35:40 +01:00
Wolfgang Denk
32bf3d143a Fix quoting problem (preboot setting) in many board config files.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-03-03 12:37:53 +01:00
Anatolij Gustschin
bc77881247 ppc4xx: Support for ATI Radeon 9200 card on sequoia
Adds configuration option for ATI Radeon 9200 card
support to sequoia config file. If CONFIG_VIDEO
is enabled, TEXT_BASE should be changed to 0xFFF80000.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2008-02-22 15:51:08 +01:00
Larry Johnson
214398d9cb ppc4xx: Beautify configuration files for Sequoia and Korat boards
Signed-off-by: Larry Johnson <lrj@acm.org>
2008-02-16 06:38:55 +01:00
Niklaus Giger
4d332dbeb0 ppc4xx: Make Sequoia boot vxWorks
vxWorks expects in
TLB 0 a entry for the Machine Check interrupt
TLB 1 a entry for the RAM
TLB 2 a entry for the EBC
TLB 3 a entry for the boot flash

After changing the baudrate to 9600 I had no problems to boot the
vxWorks image as distributed by WindRiver (Revision 2.0/1 from
June 18, 2007)

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
2008-01-10 19:06:54 +01:00
Lawrence R. Johnson
b05e8bf58b ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Sequoia board
Note: this patch changes the configuration of some GPIO registers:

   Register      Old Value   New Value
---------------  ----------  ----------
DCR GPIO0_TCR    0x0000000F  0x0000F0CF
DCR GPIO0_TSRH   0x55005000  0x00000000
DCR GPIO1_TCR    0xC2000000  0xE2000000
DCR GPIO1_TSRL   0x0C000000  0x00200000
DCR GPIO1_ISR2L  0x00050000  0x00110000

Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-04 11:39:05 +01:00
Stefan Roese
42d55ea0bd ppc4xx: Move virtual address of POST cache test to bigger address
On Sequoia & LWMON5 the virtual address of the POST cache test is now
moved to a bigger address. This enables usage of more memory on those
boards.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27 19:35:35 +01:00
Stefan Roese
328a340392 ppc4xx: fdt: Cleanup setup of cpu node setup
Now the cpu node setup ("timebase-frequency" and "clock-frequency") is
without using the absolute path to the cpu node. This makes it possible
to use this U-Boot version with both versions of cpu-node naming
"cpu@0" and the former "PowerPC,440EPx@0".

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27 19:35:34 +01:00
Markus Klotzbücher
052440b022 ppc4xx: Add CONFIG_BOOTP_SUBNETMASK to Sequoia board config
When using dhcp/bootp the "netmask" environment variable is not
set because CONFIG_BOOTP_SUBNETMASK is not defined. But usually this is
desireable, so the following patch adds this this option to the board
config.

Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27 19:35:33 +01:00
Stefan Roese
136288847e ppc4xx: Bring 4xx fdt support up-to-date
This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27 19:35:32 +01:00
Matthias Fuchs
2d14684341 ppc4xx: Use generic usb-ohci driver for sequoia board
This patch makes the sequoia board use the generic usb-ohci driver
instead of cpu/ppc4xx/usb_ohci.c.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-11-09 16:42:15 +01:00
Stefan Roese
d25dfe08fb ppc4xx: Remove cache definition from 4xx board config files
All 4xx board config files don't need the cache definitions anymore.
These are now defined in common headers.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:21:47 +01:00
Stefan Roese
5a5958b7de ppc4xx: Fix incorrect 33/66MHz PCI clock log-message on Sequoia & Yosemite
The BCSR status bit for the 66MHz PCI operation was correctly
addressed (MSB/LSB problem). Now the correct currently setup
PCI frequency is displayed upon bootup.

This patch also fixes this problem on Rainier & Yellowstone, since these
boards use the same souce code as Sequoia & Yosemite do.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-15 11:29:33 +02:00
Gary Jennejohn
81b73dec16 ppc4xx: (Re-)Enable CONFIG_PCI_PNP on AMCC 440EPx Sequoia
The 440EPx has a problem when the PCI_CACHE_LINE_SIZE register is
set to non-zero, because it doesn't support MRM (memory-read-
multiple) correctly. We now added the possibility to configure
this register in the board config file, so that the default value
of 8 can be overridden.

Here the details of this patch:

o drivers_pci_auto.c: introduce CFG_PCI_CACHE_LINE_SIZE to allow
  board-specific settings. As an example the sequoia board requires 0.
  Idea from Stefan Roese <sr@denx.de>.
o board/amcc/sequoia/init.S: add a TLB mapping at 0xE8000000 for the
  PCI IO-space. Obtained from Stefan Roese <sr@denx.de>.
o include/configs/sequoia.h: turn CONFIG_PCI_PNP back on and set
  CFG_PCI_CACHE_LINE_SIZE to 0.

Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-31 15:21:46 +02:00
Stefan Roese
9de469bd96 ppc4xx: Only enable POST FPU test on Sequoia and not Rainier
Signed-off-by: Stefan Roese <sr@denx.de>
2007-08-16 10:18:33 +02:00
Andy Fleming
6bf6f114dc Merge branch 'testing' into working
Conflicts:

	CHANGELOG
	fs/fat/fat.c
	include/configs/MPC8560ADS.h
	include/configs/pcs440ep.h
	net/eth.c
2007-08-03 02:23:23 -05:00
Jon Loeliger
079a136c35 include/configs/[p-z]* + misc: Cleanup BOOTP and lingering CFG_CMD_*.
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.

Remove lingering references to CFG_CMD_* symbols.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-07-10 10:12:10 -05:00
Jon Loeliger
46da1e96b7 include/configs: Use new CONFIG_CMD_* in various s* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-07-05 11:05:13 +02:00
Sergei Poselenov
b44896215a Merged POST framework with the current TOT.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
2007-07-05 08:17:37 +02:00
Stefan Roese
e4feb7638c Merge with git://www.denx.de/git/u-boot.git 2007-06-25 20:20:30 +02:00
Stefan Roese
466fff1a7b ppc4xx: Add pci_pre_init() for 405 boards
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-25 15:57:39 +02:00
Wolfgang Denk
1636d1c852 Coding stylke cleanup; rebuild CHANGELOG 2007-06-22 23:59:00 +02:00
Igor Lisitsin
a11e06965e Extend POST support for PPC440
Added memory, CPU, UART, I2C and SPR POST tests for PPC440.

Signed-off-by: Igor Lisitsin <igor@emcraft.com>
--
2007-06-22 23:21:01 +02:00
Grzegorz Bernacki
efa35cf12d ppc4xx: Clean up 440 exceptions handling
- Introduced dedicated switches for building 440 and 405 images required
  for 440-specific machine instructions like 'rfmci' etc.

- Exception vectors moved to the proper location (_start moved away from
  the critical exception handler space, which it occupied)

- CriticalInput now serviced (with default handler)

- MachineCheck properly serviced (added a dedicated handler and return
  subroutine)

- Overall cleanup of exceptions declared with STD_EXCEPTION macro (unused,
  unhandled and those not relevant for 4xx were eliminated)

- Eliminated Linux leftovers, removed dead code

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-15 11:19:28 +02:00
Stefan Roese
f3679aa13d Merge with /home/stefan/git/u-boot/bamboo-nand 2007-06-01 16:15:34 +02:00
Stefan Roese
9d9096043e ppc4xx: Update Sequoia NAND booting support with ECC
Signed-off-by: Stefan Roese <sr@denx.de>
2007-06-01 15:29:04 +02:00
Jeffrey Mann
193b4a3bb3 [PATCH] ppc4xx: Fix CONFIG_SYS_CLK_FREQ definition in Sequoia config file
A '3' got cut off in the formatting of the last patch to automatically
change the clock speed of the system clock on sequoia board.

Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-07 19:42:49 +02:00
Jeffrey Mann
e3b8c78bc2 ppc4xx: Detect if the sysclk on Sequoia is 33 or 33.333 MHz
The AMCC Secquoia board has been changed in a new revision from using a
33.000 MHz clock to a 33.333 MHz system clock. A bit in the CPLD
indicates the difference. This patch reads that bit and uses the correct
clock speed for the board. This code is backward compatable will all
prior boards. All prior boards will be read as 33.000.

Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-05 08:32:14 +02:00
Stefan Roese
430f1b0f9a Merge some AMCC make targets to keep the top-level Makefile smaller
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-28 15:03:16 +02:00
Stefan Roese
2db633658b [PATCH] Small Sequoia cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
2007-03-24 15:55:58 +01:00
Stefan Roese
4be23a12f2 [PATCH] Update Sequoia EBC configuration (NOR FLASH)
As spotted by Matthias Fuchs, the READY input should not be
enabled for the NOR FLASH on the Sequoia board.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-02-19 08:23:15 +01:00
Stefan Roese
23744d6b5b [PATCH] Remove PCI-PNP configuration from Sequoia/Rainier config file
When PCI PNP is enabled the pci pnp configuration routine is called
which sets the PCI_CACHE_SIZE_LINE to 8. This seems to generate some
problems with some PCI cards. For now disable the PCI PNP configuration.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-02-01 13:22:41 +01:00
Stefan Roese
e802594b6f [PATCH] Update Sequoia (440EPx) config file
The config file now handles the 2nd target, the Rainier (440GRx)
evaluation board better. Additionally the PPC input clock was
adjusted to match the correct value of 33.0 MHz.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-30 17:06:10 +01:00
Stefan Roese
0238898382 [PATCH] Add DDR2 optimization code for Sequoia (440EPx) board
This code will optimize the DDR2 controller setup on a board specific
basis.

Note: This code doesn't work right now on the NAND booting image for the
Sequoia board, since it doesn't fit into the 4kBytes for the SPL image.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-01-05 10:38:05 +01:00
Stefan Roese
d1a7254529 [PATCH] Select NAND embedded environment from board configuration
The current NAND Bootloader setup forces the environment
variables to be in line with the bootloader. This change
enables the configuration to be made in the board include
file instead so that it can be individually enabled.

Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2006-11-27 17:34:10 +01:00
Stefan Roese
4ef6251403 [PATCH] Update AMCC Sequoia config file to support 64MByte NOR FLASH
Signed-off-by: Stefan Roese <sr@denx.de>
2006-11-20 20:39:52 +01:00