Commit graph

21 commits

Author SHA1 Message Date
Kim Phillips
b211575740 mpc83xx: bump loadaddr over fdtaddr to 0x500000
this seems as a good compromise between human memory, typing,
and last but not least, to accommodate for current and future kernel bloat.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
2008-04-25 10:54:06 -05:00
Timur Tabi
89c7784ed9 83xx: Add Vitesse VSC7385 firmware uploading
Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware.  Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-03-25 19:16:43 -05:00
Poonam Aggrwal
e1d8ed2c08 Changes in uboot DDR configuration for MPC8313eRDB
These changes were identified by HighSmith Bill ,Mazzyar and Joseph for
DDR configuration in u-boot code. Some are related to performance, some
affect stability and some correct few basic errors in the current
configuration.

The changes have been tested and found to give better memory latency
figures on MPC8313eRDB.LMBench figures prove it.

The changes are:

- CS0_CONFIG[ AP_n_EN] is changed from 1 to 0
  (this may improve performance for application with many read
  or write to open pages).
- CS0_CONFIG[ODT_WR_CFG] is currently changed from 100 to
  001 (activating all the CS when only one is used may cause
  unwanted noise on the system)

- TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 8clks (based on
  Tras=45ns)
- TIMING_CFG_1[REFREC] changed from 21 clks to 18clks.

- TIMING_CFG_2[AL] value changed from 0 setting to 1 clk to
  comply with the 3 ODT clk requirements)
- TIMING_CFG_2[CPO] was set to a reserved value, changed to RL+3/4.
- TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 6clks.

- DDR_SDRAM_MODE[AL]changed from 0 to 1.
- DDR_SDRAM_MODE[WRREC] changed from 1 clk to 3 clks.

- DDR_SDRAM_INTERVAL[REFINT] is changed from 0x0320 to 0x0510.
- DDR_SDRAM_INTERVAL[BSTOPRE] is changed from 0x64 to 0x0500.

The patch is based of git://www.denx.de/git/u-boot-mpc83xx.git
The last commit on this tree was 6775c68683

Signed-off-by: Poonam Aggrwal-b10812 <b10812@freescale.com>
Cc: Bill HighSmith <Bill.Highsmith@freescale.com>
Cc: Razzaz Mazyar <MRazzaz@freescale.com>
Cc: Josep P J <PJ.Joseph@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16 12:00:49 -06:00
Dave Liu
2c5b48fc20 mpc83xx: Remove cache config from config.h
clean up the cache config from configs.h of board

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-10 21:06:32 -06:00
Marcel Ziswiler
7817cb2083 fix comments with new drivers organization
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2008-01-09 21:48:49 +01:00
Kim Phillips
5b8bc606c6 mpc83xx: convert to using do_fixup_*()
convert to using simpler mpc85xx style fdt update code; streamline by
eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm
the old school FLAT_TREE code from 83xx (since the sbc8349 was just
converted over to using libfdt).

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-08 09:56:42 -06:00
Timur Tabi
b2893e1fcb 83xx: fix CFG_ENV_ADDR and CFG_ENV_SECT_SIZE definitions
Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for all of the
currently-defined 83xx boards.  This change guarantees that the environment
will be located on the first flash sector after the U-Boot image.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-08 09:55:39 -06:00
Kim Phillips
3bb342fc85 fdt: remove unused OF_FLAT_TREE_MAX_SIZE references
and make some minor corrections to the FDT part of the README.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-08-29 01:46:25 +02:00
Wolfgang Denk
8f22b671eb Merge with /home/wd/git/u-boot/custodian/u-boot-mpc85xx 2007-08-18 21:50:01 +02:00
Wolfgang Denk
1d55483cf7 Merge with /home/wd/git/u-boot/custodian/u-boot-mpc83xx 2007-08-18 21:47:33 +02:00
Kim Phillips
bbea46f76f mpc83xx: implement board_add_ram_info
add board_add_ram_info, to make memory diagnostic output more
consistent. u-boot banner output now looks like:

DRAM:  256 MB (DDR1, 64-bit, ECC on)

and for boards with SDRAM on the local bus, a line such as this is
added:

SDRAM: 64 MB (local bus)

also replaced some magic numbers with their equivalent define names.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-08-16 23:12:24 -05:00
Andy Fleming
10327dc554 Add CONFIG_HAS_ETH0 to all boards with TSEC
The 85xx code now relies on CONFIG_HAS_ETH0 to determine whether
to update TSEC1's device-tree node, so we need to add it
to all the boards with TSECs.  Do this for 83xx and 86xx, too,
since they will eventually do something similar.

Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-08-16 16:35:02 -05:00
Andy Fleming
3a79013e2a Define tsec flag values in config files
The tsec_info structure and array has a "flags" field for each
ethernet controller.  This field is the only reason there are
settings.  Switch to defining TSECn_FLAGS for each controller
in the config header, and we can greatly simplify the array, and
also simplify the addition of future boards.

Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-08-16 12:12:49 +02:00
Kim Phillips
35cc4e4823 mpc83xx: enable libfdt by default on freescale boards
this enables libfdt code by default for the
freescale mpc8313erdb, mpc832xemds, mpc8349emds,
mpc8349itx and gp boards.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-08-15 22:36:33 -05:00
Wolfgang Denk
cdd917a43d Fix build errors and warnings / code cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-08-02 00:48:45 +02:00
Jon Loeliger
079a136c35 include/configs/[p-z]* + misc: Cleanup BOOTP and lingering CFG_CMD_*.
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.

Remove lingering references to CFG_CMD_* symbols.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-07-10 10:12:10 -05:00
Jon Loeliger
8ea5499afd include/configs: Use new CONFIG_CMD_* in 83xx board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-07-05 11:04:05 +02:00
Kim Phillips
255a3577c8 Reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx
For all practical u-boot purposes, TSECs don't differ throughout the
mpc8[356]xx families; reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-05-17 00:07:21 +02:00
Wolfgang Denk
a7676ea773 Minor Coding Style cleanup, update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-05-16 01:16:53 +02:00
Kim Phillips
5c5d324293 mpc83xx: minor fixups for 8313rdb introduction 2007-04-25 12:34:38 -05:00
Scott Wood
96b8a05432 mpc83xx: Add MPC8313ERDB support.
Signed-off-by: Scott Wood <scottwood@freescale.com>
2007-04-23 16:32:10 -05:00