Commit graph

18 commits

Author SHA1 Message Date
Rob Herring
cdb23792e8 config: remove platform CONFIG_SYS_HZ definition part 1/2
Remove platform CONFIG_SYS_HZ definition for configs A-Z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:05:59 -05:00
Rob Herring
0defddc851 config: Add a default CONFIG_SYS_PROMPT
The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this the default. The rest of the boards remain unchanged to avoid
breaking any external scripts expecting a certain prompt.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-11-04 11:02:14 -05:00
Shaohui Xie
83d925668f powerpc/B4860: enable PBL tool for B4860
Use a default RCW of protocol 0x2A_0x98, and a PBI configure file which
uses CPC1 as 512KB SRAM, then PBL tool can be used on B4860 to build a
pbl boot image.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2013-10-16 16:13:12 -07:00
Po Liu
0d2cff2d9e powerpc: add CONFIG_SECURE_BOOT condition into fsl_secure_boot.h
This patch is for board config file not to add CONFIG_SECURE_BOOT
condition for include the asm/fsl_secure_boot.h.

Signed-off-by: Po Liu <Po.Liu@freescale.com>
2013-10-16 16:13:10 -07:00
Minghuan Lian
0795eff34c powerpc/rman: fix RMan support for t4240 and b4860
1. Add CONFIG_SYS_DPAA_RMAN macro to t4240 and b4860.
2. Decrease RMan liodn offset number.
SET_RMAN_LIODN() is used to set liodn offset of RMan blocks 0-3.
For t4240 and b4860, RMan liodn base is assigned to 922, the original
offset number is too large that the liodn (base+offset 922+678 = 1600)
is greater than 0x500 the maximum liodn number.

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09 12:41:41 -07:00
Shaveta Leekha
cb033741f4 board/b4860qds: Add support for configuring SerDes1 Refclks
1) Add support in B4860 board files for using IDT driver where
   IDT8T49N222A is a low phase noise Frequency Translator / Synthesizer
   that generate different refclks for SerDes modules, used this driver
   for reconfiguring SerDes1 Refclks(based on SerDes1 protocols)
   for CPRI to work. CPRI works on 122.88MHz and default refclks coming
   on board are not suitable for it
2) Move SerDes1 refclk1 source selection from eth_b4860qds.c file
   to b4860qds board file, as SerDes1 Refclk1 would come from
   PHY MUX in case of certain protocols, that have been checked here.
   This change would make on board SGMIIs to work
3) Add I2C addresses for IDT8T49N222A devices in board/include file
4) Add define for PCA-I2C bus multiplexer, on which IDT devices exist

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-09 12:41:41 -07:00
York Sun
d2ab4bbc7b powerpc/corenet: Move CONFIG_FSL_CORENET out of board header file
Move CONFIG_FSL_CORENET define to config_mpc85xx.h. It is not board
specific feature and belongs to SoC header.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09 12:41:38 -07:00
Tom Rini
c2120fbfbc Merge branch 'master' of git://git.denx.de/u-boot-i2c
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
	board/sandburst/common/ppc440gx_i2c.c
	board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:50:24 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Heiko Schocher
00f792e0df i2c, fsl_i2c: switch to new multibus/multiadapter support
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
2013-07-23 08:34:53 +02:00
Prabhakar Kushwaha
4d0e6e0d73 board/b4860qds: Relax NOR flash teadc timing parameter
Relax parameters to give address latching more time to setup.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:50 -05:00
Liu Gang
5870fe44b2 powerpc/b4860qds: Slave module for boot from SRIO and PCIE
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
	1. Set all the cores in holdoff status.
	2. Set the boot location to one PCIE or SRIO interface by RCW.
	3. Set a specific TLB entry for the boot process.
	4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
	5. Set a specific TLB entry in order to fetch ucode and ENV from
	   master.
	6. Set a LAW entry with the TargetID one of the PCIE ports for
	   ucode and ENV.
	7. Slave's u-boot image should be generated specifically by
	   make xxxx_SRIO_PCIE_BOOT_config.
	   This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.

For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:48 -05:00
Liu Gang
3a01799b35 powerpc/b4860qds: Enable master module for boot from SRIO and PCIE
B4860QDS can support the feature of Boot from SRIO/PCIE, and the macro
"CONFIG_SRIO_PCIE_BOOT_MASTER" will enable the master module of this feature
when building the u-boot image.

You can get some description about this macro in README file, and for more
information about the feature of Boot from SRIO/PCIE, please refer to the
document doc/README.srio-pcie-boot-corenet.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:48 -05:00
Gabor Juhos
842033e696 pci: introduce CONFIG_PCI_INDIRECT_BRIDGE option
The pci_indirect.c file is always compiled when
CONFIG_PCI is defined although the indirect PCI
bridge support is not needed by every board.

Introduce a new CONFIG_PCI_INDIRECT_BRIDGE
config option and only compile indirect PCI
bridge support if this options is enabled.

Also add the new option into the configuration
files of the boards which needs that.

Compile tested for powerpc, x86, arm and nds32.
MAKEALL results:

powerpc:
  --------------------- SUMMARY ----------------------------
  Boards compiled: 641
  Boards with warnings but no errors: 2 ( ELPPC MPC8323ERDB )
  ----------------------------------------------------------
  Note: the warnings for ELPPC and MPC8323ERDB are present even
  without the actual patch.

x86:
  --------------------- SUMMARY ----------------------------
  Boards compiled: 1
  ----------------------------------------------------------

arm:
  --------------------- SUMMARY ----------------------------
  Boards compiled: 311
  ----------------------------------------------------------

nds32:
  --------------------- SUMMARY ----------------------------
  Boards compiled: 3
  ----------------------------------------------------------

Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
2013-06-07 14:17:01 -04:00
Shaveta Leekha
6eaeba23dd powerpc/b4860qds: Add LAW Target ID and Create LAW entry for Maple
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:14 -05:00
Poonam Aggrwal
8fa0102bcf powerpc/B4: Merge B4420 and B4860 in config_mpc85xx.h
B4420 is a subset of B4860. Merge them in config_mpc85xx.h to simplify
the defines.
- Removed #define CONFIG_SYS_FSL_NUM_CLUSTERS as this is used nowhere.
- defined CONFIG_SYS_NUM_FM1_10GEC to 0 for B4420 as it does not have 10G.

Also move CONFIG_E6500 out of B4860QDSds.h into config_mpc85xx.h.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:14 -05:00
Suresh Gupta
16d88f415a Enable XAUI interface for B4860QDS
- Added SERDES2 PRTCLs = 0x98, 0x9E
- Default Phy Addresses for Teranetics PHY on XAUI card
	The PHY addresses of Teranetics PHY on XAUI riser card are assigned
	based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on
	AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1
        and slot2
- Configure MDIO for 10Gig Mac

Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:12 -05:00
York Sun
b5b06fb7b0 powerpc/b4860qds: Added Support for B4860QDS
B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.

B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
  ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,  ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
  16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
  8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
  RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
  connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
  connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
  configuration reset source. The RCW source is set by appropriate
  DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
	- On-board eCWTAP controller with ETH and USB I/F
	- JTAG/COP 16-pin header for any external TAP controller
	- External JTAG source over AMC to support B2B configuration
	- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
	- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
  DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
  - total four refclk, including CPRI clock scheme

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30 11:25:11 -06:00