Enable i2c driver model for am335x_boneblack_vboot as omap i2c
supports driver model. Also enable CONFIG_DM_I2C_COMPAT for
legacy drivers of i2c devices.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since omap's spl doesn't support DM currently, do not define
DM_I2C for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
RK3399 is a SoC from Rockchip with dual-core Cortex-A72
and quad-core Cortex-A53 CPU. It supports two USB3.0
type-C ports and two USB2.0 EHCI ports. Other interfaces
are very much like RK3288, the DRAM are 32bit width address
and support address from 0 to 4GB-128MB range.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable fastboot feature on rk3288.
This path doesn't support the fastboot flash function command entirely.
We will hit "cannot find partition" assertion without specified
partition environment. Define gpt partition layout in specified board
such as firefly-rk3288, then enjoy it!
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).
evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If we would like to boot from SD card, we have to implement mmc driver
in SPL stage, and get a slightly large SPL binary. Rockchip SoC's
bootrom code has the ability to load spl and u-boot, then boot.
If CONFIG_ROCKCHIP_SPL_BACK_TO_BROM is enabled, the spl will return to
bootrom in board_init_f(), then bootrom loads u-boot binary.
Loading sequence after rework:
bootrom ==> spl ==> bootrom ==> u-boot
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed up spelling of U-Boot, boorom, opinion->option, Rochchip:
Signed-off-by: Simon Glass <sjg@chromium.org>
Most users of CONFIG_I2C_EEPROM were migrated to defconfig a while ago,
but sandbox was skipped. Leave it off for sandbox_spl where it does not
build, but does not need to be either.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Sandbox is built with 64-bit ints by default. This doesn't work properly on
32-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
On some sunxi boards we have NANDs exposing 1664 OOB bytes per page.
Define the CONFIG_SYS_NAND_MAX_ECCPOS value accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We already have an SPL driver for the sunxi NAND controller, now add
the normal/standard one.
The source has been copied from Linux 4.6 with a few changes to make
it work in u-boot.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Convert IGEP board to use UBI volumes for U-Boot, its environment and
kernel. With exception of first four sectors read by SoC boot
ROM whole (One)NAND is UBI managed.
Also merge NAND and OneNAND defconfigs as now one binary can serve
both flashes.
As code is too big now, drop CONFIG_SPL_EXT_SUPPORT to make it fit.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Remove unnecessary board specifc config files for
zynq boards(microzed, picozed, ZC770(all), zed) and point
to zynq common config file.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable config CONFIG_SYS_NO_FLASH through defconfig
for all zynq boards.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define config USB_STORAGE through defconfig for all
respective zynq boards
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add Kconfig entry config option for USB_EHCI_ZYNQ
and update the same to enable for all zynq boards
which supports USB
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The EP platform also has working AHCI emulation, so I see little reason
not to implement the plumbing for it that enables us to boot from AHCI.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Loading the fdt at 0xc00000 fails if the uncompressed kernel image is
greater than 12 MiB, which is quite common with modern kernels and
multiplatform defconfigs. Move fdtaddr to 0x1e00000 which is just under
the ramdiskaddr on most targets.
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In non-secure boot scenario from NAND, this address will map to CPC
configured as SRAM. But in case of secure boot, this default address
always maps to IBR (Internal Boot ROM).
The IBR code requires that the bootloader(U-boot) must lie in 0 to 3.5G
address space i.e. 0x0 - 0xDFFFFFFF.
For secure boot target from NAND, the text base for SPL is kept same as
non-secure boot target i.e. 0xFFFx_xxxx but the SPL U-boot binary will
be copied to CPC configured as SRAM with address in 0-3.5G(0xBFFC_0000)
As a the virtual and physical address of CPC would be different. The
virtual address 0xFFFx_xxxx needs to be mapped to physical address
0xBFFx_xxxx.
Create a new PBI file to configure CPC as SRAM with address 0xBFFC0000
and update DCFG SCRTACH1 register with location of Header required for
secure boot.
The changes are similar to
commit 467a40dfe3
powerpc/mpc85xx: SECURE BOOT- NAND secure boot target for P3041
While P3041 has a 1MB CPC and does not require SPL. On T104x, CPC
is only 256K and thus SPL framework is used.
The changes are only applicable for SPL U-Boot running out of CPC SRAM
and not the next level U-Boot loaded on DDR.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Due to the blow up of the latest kernel size, the default gnuzip
size (8M) seems too small. The yocto kernel size I built for
mpc8315erdb board is 5294393, and it can't be boot by using the
latest u-boot. So expand gnuzip buffer for all the mpc83xx boards
to fix this issue.
Robert P. J. Day also pointed that the kernel partition on the NAND
flash is also too small, fix it at the same time.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Robert P. J. Day has pointed that the value of SYS_MONITOR_LEN in
MPC8315ERDB.h is smaller than the u-boot.bin. This will cause the
overlap between the code of u-boot and the environment variable.
So when executing saveenv, it will corrupt the code of u-boot and
causes the board not boot. Fix this for all the mpc83xx boards by
reserving a 512K area.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Kevin Hao <kexin.hao@windriver.com>
Reviewed-by: York Sun <york.sun@nxp.com>
I2C offset was changed by commit 00f792e0 (added multibus support)
from 0x3100 to 0x3000. This typo leads to error when reading SPD
from DDR DIMMs.
Signed-off-by: Benjamin Kamath <bkamath@spaceflight.com>
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The PPA use PSCI to make secondary cores bootup. So when PPA was
enabled, add the CONFIG_ARMV8_PSCI to identify the SMP boot-method
between PSCI and spin-table.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use existing Kconfig symbols to let the user configure whether to
build a U-Boot with non-secure mode support or not. This also allows
to enable virtualization extension easily.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
CONFIG_DISPLAY_BOARDINFO should not be placed in mx7_common
because some boards might need a different config such as
CONFIG_DISPLAY_BOARDINFO_LATE. Move it to the board file
instead.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This can be useful if the same U-Boot binary is used for boards
available with a i.MX 7Solo and i.MX 7Dual.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The cm-fx6 module has an on-board spi flash chip. Enable mtd support
and the mtdparts command. Also define a default partitioning, add
it to the default environment, and enable support to overwrite the
partitioning defined in a device tree by it. Finally, probe for the
chip on preboot to register the flash chip and, thus, establish the
connection between the mtd environment settings and the actual device.
These changes move the effective default partitioning from the device
tree shipped with the vendor kernels to U-Boot which becomes the single
point of definition for the partitioning for all device tree based
kernels (in particular, for the upstream Linux kernel which does not
have a default partitioning defined in its device tree).
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Currently, entire script segments have to be changed in the default
environment to change the kernel image location or to append kernel
cmdline parameters. In the later case this has to be changed for
every possible boot device.
Introduce new variables for kernel image locations and boot device
independent kernel parameters to make it easier to change these
settings.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Nikita Kiryanov <nikita@compulab.co.il>
Recently I started to notice that u-boot.img built for Wandboard
by some toolchains becomes so large that it basically overlaps with
U-Boot environment area on SD-card.
According to
http://wiki.wandboard.org/index.php/Boot-process#sdcard_boot_data_layout
Wandboard's SD-card layout is as follows:
------------------------------>8---------------------------
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
==========================================================
1. 0x00000000 Reserved For MBR
2. 0x00000200 512 Secondary Image Table (optional)
3. 0x00000400 1024 uBoot Image (Starting From IVT)
4. 0x00060000 393216 start of uboot env (size:8k)
5. 0x00062000 end of uboot env
6. 0x00100000 1048576 Linux kernel start
7. 0x0076AC00 7777280 start of partition 1
------------------------------>8---------------------------
So for U-Boot we have 383kB (392192 bytes).
But in up to date U-Boot for Wandboard we build separately
a) SPL
b) u-boot.img
which gives us a bit more detailed SD-card layout:
------------------------------>8---------------------------
==========================================================
1. 0x00000000 Reserved For MBR
2. 0x00000200 512 Secondary Image Table (optional)
3. 0x00000400 1024 SPL
4. 0x00011400 70656 u-boot.img
5. 0x00060000 393216 start of uboot env (size:8k)
6. 0x00062000 end of uboot env
...
------------------------------>8---------------------------
>From that layout we may calculate amount of space reserved for
u-boot.img. It's just 315kb (322560 bytes).
Now if I build U-Boot with Sourcery CodeBench ARM 2014.05 produced
u-boot.img is already more than we expected
(323840 bytes instead of "< 322560"):
------------------------------>8---------------------------
ls -la u-boot.img
-rw-rw-r-- 1 user user 323840 Jul 5 07:38 u-boot.img
------------------------------>8---------------------------
Funny enough if I rebuild U-Boot with ARM toolchain available in
my Fedora 23 distro u-boot.img becomes a little bit smaller:
------------------------------>8---------------------------
ls -la u-boot.img
-rw-rw-r-- 1 user user 322216 Jul 5 07:39 u-boot.img
------------------------------>8---------------------------
What's worse this problem might not affect people most of the time
because what happens people would just copy u-boot.img on SD-card and
live in happiness with it... well until somebody attempts to save
environment in U-Boot with "saveenv" command which will simply
overwrite the very end of u-boot.img.
That will lead to unusable SD-card until user dd u-boot.img on
SD-card again.
I may foresee this issue in the future to become more visible once we
add more features in U-Boot for Wandboard or just existing code base
becomes bulkier and people will consistently get larger u-boot.img
files produced.
IMHO there's an obvious solution for all that - just move U-Boot's env
to the very end of the gap between U-Boot and the first real partition
on the SD-card. This patch will follow
8fb9eea565 ("mx6sabre_common: Fix U-Boot corruption after 'saveenv'").
So env is still not in the very end of the gap (obviously 256kb is way
too much for U-Boot's env) but at least we have now the same
partitioning for i.MX6 boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Wolfgang Denk <wd@denx.de>
The code had assumed 4 CPUS before and now we have this configurable.
For now, set this to the previous default.
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The original PSCI implementation assumed CONFIG_ARMV7_PSCI_NR_CPUS=4.
Add this to platforms that have not defined it, using CONFIG_MAX_CPUS if
it is defined, or the actual number of cores for the given platform.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:
https://linux-sunxi.org/Bootable_SPI_flash
This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.
While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.
Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)
Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:
sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin
The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Start up the test devices. These print out of-platdata contents, providing a
check that the of-platdata feature is working correctly.
The device-tree changes are made to sandbox.dts rather than test.dts. since
the former controls the of-platdata generation.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to build SPL for sandbox. It provides additional
build coverage and allows SPL features to be tested in sandbox. However
it does not need worthwhile to always create an SPL build. It nearly
doubles the build time and the feature is (so far) seldom used.
So for now, create a separate build target for sandbox SPL. This allows
experimentation with this new feature without impacting existing workflows.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds SDRAM support for stm32f746 discovery board.
This patch depends on previous patch.
This patch is based on STM32F4 and emcraft's[1].
[1]: https://github.com/EmcraftSystems/u-boot
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
This patch adds 200MHz clock configuration for stm32f746 discovery board.
This patch is based on STM32F4 and emcraft's[1].
[1]: https://github.com/EmcraftSystems/u-boot
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
Make the external devices the preferred ones when booting the system
(usb is already the first option). This allows users to easily boot
custom distributions without requiring them to reflash/customize u-boot.
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Ricardo Salveti <rsalveti@rsalveti.net>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Andreas Färber <afaerber@suse.de>
Acked-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Define a default board_run_command() function. This function contains
the commands needed to boot the board when CLI is disabled (CONFIG_CMDLINE=n).
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Add USB host support.
Tested by connecting a USB pen drive:
=> usb start
starting USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add script for retrieving the kernel via TFTP and mounting the
rootfs via NFS.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
DFU is a convenient way to program U-boot binary into the eMMC.
Add support for it.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Pico-imx6ul has a KSZ8081 Ethernet PHY.
Add support for it.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
Custom Board based on MX6 Dual, 1GB RAM and eMMC.
There are two variants of the board with and without
PCIe (ZC5202 and ZC5601).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add support for Advantech SOM-DB5800 with the SOM-6867 installed.
This is very similar to conga-qeval20-qa3-e3845 in that there is a
reference carrier board (SOM-DB5800) with a Baytrail based SoM (SOM-6867)
installed.
Currently supported:
- 2x UART (From ITE EC on SOM-6867) routed to COM3/4 connectors on
SOM-DB5800.
- 4x USB 2.0 (EHCI)
- Video
- SATA
- Ethernet
- PCIe
- Realtek ALC892 HD Audio
Pad configuration for HDA_RSTB, HDA_SYNC, HDA_CLK, HDA_SDO
HDA_SDI0 is set in DT to enable HD Audio codec.
Pin defaults for codec pin complexs are not changed.
Not supported:
- Winbond Super I/O (Must be disabled with jumpers on SOM-DB8500)
- USB 3.0 (XHCI)
- TPM
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This option is not actually needed for rockchip boards. Drop it, since it
will not support driver-model MMC operation support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable Cadence QSPI controller support to use QSPI on K2G SoC. Also
enable Spansion flash support to access s25fl512s flash present on K2G
QSPI bus.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Since Keystone2 devices do not have support DM in SPL, do not define
DM_SPI and DM_SPI_FLASH for SPL build.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Commit 9262367 moves USB errata workaround into a C file. This
causes compiling error for kmcoge4 and kmlion1. To enable the
errata workaround, define CONFIG_USB_EHCI_FSL in common header.
Signed-off-by: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ed Swarthout <Ed.Swarthout@nxp.com>
Cc: Sriram Dash <sriram.dash@nxp.com>
Fixes: 92623672f9 ("fsl: usb: make errata function common for PPC and ARM")
As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2
means the autoboot with no delay, with no abort check even if
CONFIG_ZERO_BOOTDELAY_CHECK is defined.
To sum up, the autoboot behaves as follows:
[1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
autoboot with no delay, with no check for abort
[3] CONFIG_BOOTDELAY=-1
disable autoboot
[4] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
As you notice, [2] and [4] come to the same result, which means we
do not need CONFIG_ZERO_BOOTDELAY_CHECK. We can control all the
cases only by CONFIG_BOOTDELAY, like this:
[1] CONFIG_BOOTDELAY=0
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=-1
disable autoboot
[3] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
This commit converts the logic as follow:
CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
--> CONFIG_BOOTDELAY=-2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicronenergy.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Now I2C is initialized early enough to access FPGA so it supports to
show board info as early as other boot methods.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
add DM and DTS support for the at91 based siemens
boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
I still see some defines of this config in board headers. Move them
to defconfigs (+ renaming to CONFIG_HUSH_PARSER) to complete this
migration.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Introduce a meson-gxbb-common.h header file and derive the
configuration for Hardkernel Odroid-C2 board from that.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
This fixes commit d31e9c575f ,
which broke booting from SD card on all SoCFPGA boards. The
patch assumes the bootloader partition to be partition 3, at
the end of the SD card, which doesn't make any sense. U-Boot
assumes the bootloader partition is partition 1 or that the
bootloader image is at offset +1 MiB from the start of SD card.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Sylvain Lesne <lesne@alse-fr.com>
Due to changes in distro environment, ENV_SIZE limit was reached on Dragonboard.
This patch increases environment size to 8KiB.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
At first, 256 byte of the head of DRAM space was reserved for some
reasons. However, as the progress of development, it turned out
unnecessary, and it was never used in the end. Move the CPU release
address to leave no space.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently DFU is not working.
Adjust CONFIG_SYS_MALLOC_LEN and dfu_alt_info so that we are
able to flash u-boot.imx into the eMMC via dfu using the
following method:
=> dfu 0 mmc 0
In the host PC:
dfu-util -D u-boot.imx -a boot
This is the same approach done in the mx6sl warp board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The latest version of warp7 board provides the connection of the
WDOG1_B pin to the PMIC.
Program the watchdog to enable the WDOG1_B output which causes
a POR reset.
Based on the imx7dsabresd code.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
With updated moveconfig.py and an better default, re-generate
the migration of BOOTDELAY to the defconfig.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add initial support for NXP's S32V234 SoC and S32V234EVB board.
The S32V230 family is designed to support computation-intensive applications
for image processing. The S32V234, as part of the S32V230 family, is a
high-performance automotive processor designed to support safe
computation-intensive applications in the area of vision and sensor fusion.
Code originally writen by:
Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com>
Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
Tidy up garbage left by commit bb597c0eeb ("common: bootdelay: move
CONFIG_BOOTDELAY into a Kconfig option").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At this point, this is not referenced from anywhere, so remove it
(but it will be re-added later for a different meaning).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This board is based on Snapper 9G45 which has an Atmel AT91SAM9G45 chip and
128MB of SDRAM. It includes a small LCD, 2xUSB host, SD card, Ethernet and
two UARTs.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[apply CONFIG_BOOTDELAY transition]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
The kernel can now use DT to reserve memory carveouts and
these areas are now the default for drivers that need reserved
memory, so reserving more here is unneeded and any memory reserved
this way will be wasted.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch adds QSPI boot support for LS2080AQDS board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then we can switch to booting from QSPI memory space.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When QSPI is enabled, NOR flash and QIXIS can't be accessed
through IFC due to pin mux. Enable I2C QIXIS access and I2C
early init to read the sysclk and ddrclk.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The NOR flash related configure options appear in ls2080aqds.h and
ls2080ardb.h, and the two files both includ ls2080a_common.h.
This patch remove the duplicated options in ls2080a_common.h.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since the SRAM C corruption issue is now resolved on Allwinner
A64, it is possible to move the stack top to the address 0x1A000
on both A64 and A80. The boot ROM can load SPL binaries with
up to 32 KiB size on A64 (the 24 KiB SPL size limitation only
affects A10/A20), and this patch also ensures the availability
of 8 KiB stack.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In the draco CPU board family, etamin is a new variant
with bigger flash and more RAM. Due to new flash that
uses larger pages (4K) some changes are necessary because
it impacts the MTD partition layout and the ubi mount
parameters.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Move BOOTDELAY into defconfig, just always be 3 now]
Signed-off-by: Tom Rini <trini@konsulko.com>
move CONFIG_BOOTDELAY into a Kconfig option. Used for this
purpose the moveconfig.py tool in tools.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The Boot ROM on PH1-LD11/LD20 exports built-in APIs to load images
from an eMMC device. They are useful to reduce the memory footprint
of SPL, rather than compiling the whole MMC framework.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This adds support for IS1 board. Pretty usual socfpga board,
256MB of RAM, does not have MMC, two SPI chips, one ethernet port, two
additional ethernet ports connected to the FPGA.
Signed-off-by: Pavel Machek <pavel@denx.de>
Add missing ${partnum} to set rootdev correctly when
booting from USB or MMC.
Signed-off-by: Kimmo Surakka <kimmo.surakka@ge.com>
[Rebased against v2016.05 and adjusted the variable name]
Signed-off-by: Andrew Shadura <andrew.shadura@collabora.co.uk>
The SATA support is only useful for development and shouldn't be enabled
in production, so it has to be disabled in U-boot by default.
Signed-off-by: Andrew Shadura <andrew.shadura@collabora.co.uk>
The network support is only useful for development and shouldn't be enabled
in production, so it has to be disabled in U-boot by default.
Signed-off-by: Andrew Shadura <andrew.shadura@collabora.co.uk>
The USB support is only useful for development and shouldn't be enabled
in production, so it has to be disabled in U-boot by default.
Signed-off-by: Andrew Shadura <andrew.shadura@collabora.co.uk>
The kernel already knows how to initialise the display, and initialising
the display from U-boot is only useful for debugging and isn't necessary
in production, so no need to have it enabled in U-boot by default.
Signed-off-by: Andrew Shadura <andrew.shadura@collabora.co.uk>
Avoid use of hard coded mmcdev value, use bootpart
instead, so finduuid works based on bootpart set
for a specific platform.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that all Keystone2 dts file names are changed in Linux kernel, reflect the
same in evn variables inorder to find the right dtb file.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There is a new strider console flavor with DisplayPort
video.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
Nand and QSPI are not defined now but this will be extended.
Based on selected bootmode boot_targets are rewritten.
Patch also contains detection if variables are saved. If yes don't
rewrite boot_targets variable.
Also move variable setup to the end of file because SCSI needs to be
defined before others macros are using it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
When the CONFIG_BOOTP_SERVERIP option is set, we ignore all
dhcp values for the tftp server and use our own serverip and
file name instead.
This is usually not what we want and I doubt it's set for a
good reason on ZynqMP. It definitely hurts if we want to support
uEFI PXE boot on it. So just remove the option for now.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Create an entry for "config USB_XHCI_DWC3" in Kconfig and
switch over to it for all boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.
As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.
Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
QorIQ LS1012A FREEDOM (LS1012AFRDM) is a high-performance
development platform, with a complete debugging environment.
The LS1012AFRDM board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QorIQ LS1012A Development System (LS1012AQDS) is a high-performance
development platform, with a complete debugging environment.
The LS1012AQDS board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
