Add the flag to allow runtime enviroment variable modifications.
This is being added so that the board-name can be modified at runtime
to indicate either a panda(4430) or a panda-es(4460)
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Fix the device tree loading for panda(4430) and panda-es(4460)
Modify the board name if a 4460 panda or panda-es is detected
at run time.
In the findfdt add a check for the panda-es board name and load
the panda-es device tree blob.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.
There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.
In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
As part of a review of a recent patch to add a new AM335x board, Tom
found several duplicate and/or unused #defines.
This patch simply removes them.
The two affected configs have been recompiled to check nothing was
broken (from a compilation point of view !!)
Reported-by: Tom Rini <trini@ti.com>
Signed-off-by: Mark Jackson <mpfj-list@mimc.co.uk>
Add 'optargs' variable to be set to additional kernel arguments, similar
to omap3*/am3* usage.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
The IGEP COM AQUILA and CYGNUS are industrial processors modules with
following highlights:
o AM3352/AM3354 Texas Instruments processor
o Cortex-A8 ARM CPU
o 3.3 volts Inputs / Outputs use industrial
o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
o MicroSD card reader on-board
o Ethernet controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs
Rename twl6035 to palmas to allow reuse across multiple current and
future platforms
As part of this change, change the CONFIG_TWL6035_POWER to
CONFIG_PALMAS_POWER and update usage of header file accordingly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Adds CPSW support to the TI814X EVM configured with
an ET1011C PHY in GMII mode.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Microblaze uses gpio which is connected to the system reset.
Currently gpio subsystem wasn't used for it.
Add gpio driver and change Microblaze reset logic to be done
via gpio subsystem.
There are various configurations which Microblaze can have
that's why gpio_alloc/gpio_alloc_dual(for dual channel)
function has been introduced and gpio can be allocated
dynamically.
Adding several gpios IP is also possible and supported.
For listing gpio configuration please use "gpio status" command
This patch also remove one compilation warning:
microblaze-generic.c: In function 'do_reset':
microblaze-generic.c:38:47: warning: operation on '*1073741824u'
may be undefined [-Wsequence-point]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All these macros are completely unused by any code.
CONFIG_FPGA is not a bitfield anymore.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Devcfg device requires to load bitstream in binary format.
But u-boot also has an option for loading bitstream in bit
format. Let's handle both cases by zynqpl driver.
Also add suport for loading partial bitstreams.
The first driver version was done by:
Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Add basic support for the DENX M53EVK board. Currently supported is:
MMC (incl. booting)
NAND (incl. booting)
Ethernet, I2C, USB, SATA, RTC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
With the u-boot-with-spl.bin rule calling $(OBJCOPY) with
CONFIG_SPL_PAD_TO, and CONFIG_SPL_PAD_TO defaulting to
CONFIG_SPL_MAX_SIZE we cannot use math here, so set it to 4096 rather
than 4 * 1024.
Signed-off-by: Tom Rini <trini@ti.com>
The Hydra and Superhydra (P3041DS, P5020DS, and P5040DS) boards have a
second USB port that can be configured in either host, peripheral (aka
device), or OTG (on-the-go) mode. When configured in host mode, if
the port is connected to another USB host, damage to the board can
occur.
To avoid this, we change the default setting to peripheral mode. Ideally,
we'd set it to OTG mode, but currently there is no OTG support for
these boards.
Setting the hwconfig variable will also update the device tree, and so
Linux will configure the port for peripheral mode as well.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add defines needed to access NAND, remove second flash bank that is
actually connected to NAND.
Add nand booting support for P1022DS with hardcoded DDR config using
SPL framework from 2011
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The changes to a3m071/a4m2k in summary are:
- Enable CAN1 on I2C in GPS Port Configuration
- Enable SPI on PSC2
- Activate network console
- New flash partitioning
- Fix some typos
- Pass host name to Linux
- Change rootfs to squashfs,jffs2
- Enable UBI/UBIFS support
- Enable FIT support
Signed-off-by: Stefan Roese <sr@denx.de>
The v2013.04 release has this patch set included:
5cb48582 "Add architecture-specific global data"
With this, the global_data struct is now common and new variables
have been added. Resulting in a bigger struct. Unfortunately the
currently allocated 128 bytes are just a bit too small for this
new struct.
This patch now uses the automatically generated struct size instead to
not run into this problem again.
Please note that this problem might hit some other platforms which
currently reserve a tight space of 128 bytes for the global_data
struct!
Signed-off-by: Stefan Roese <sr@denx.de>
The redundancy related defines are only correct for NAND, so guard all
of that area with CONFIG_ENV_IS_IN_NAND
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
In order to use the generic hang() later on pull libgeneric in SPL.
This has no impact on the SPL size.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
In order to use the generic hang() later on pull libgeneric in SPL.
This has no impact on the SPL size.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
With sandbox it is tricky to add an FDT to the image at build time (or
later) since we build an ELF file, not a plain binary, and the address
space of the whole U-Boot is not accessible in the emulated memory map
of sandbox.
Sandbox can read files directly from the host, though, so add an option
to read an FDT from a host file on start-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add generic board support for sandbox. and remove the old board init code.
Select CONFIG_SYS_GENERIC_BOARD for sandbox now that this is supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Pass the PHY address to the driver init to
allow parallel use of both interfaces
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Add all fixed addresses to hardware.h and change petalinux
configuration to support this.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Move baseaddr to hardware.h to be shared between
configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Watchdog can be used on Microblaze, PPC and Zynq hw designs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Setup environment and enable netconsole.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Make all mpc512x code point to the new common fsl_iim driver, and remove the
former mpc512x-specific iim driver.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This reworks the environment settings to be aligned with the other
i.MX boards. The loadaddr has been changed to allow the Freescale
kernel and mainline kernel to work without environment changes.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
FSL 2.6.35 kernel expects that revision tag is passed by the bootloader.
Select CONFIG_REVISION_TAG so that mx53 boards can work properly with 2.6.35.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Currently mmcrootfstype is set to ext3 type.
It is better not to force it in the env vars, because users may prefer a
different file system type, so let's get rid of 'mmcrootfstype'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Update the environment as done in other imx boards to allow easy switching
between booting a non-dt kernel and a dt kernel.
Change CONFIG_LOADADDR to 0x92000000, so that we can have the:
- uImage at 0x92000000
- imx51-babbage.dtb at 0x91000000
,which are adequate locations in RAM to avoid overlapping.
Boot tested the following kernels:
- 2.6.35 from FSL (11.09 branch)
- 3.9-rc7 non-dt
- 3.9-rc7 dt
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Adds support for 'bmode' command which let user to choose where to
boot from; this allows U-Boot to load system from another storage
without messing with jumpers.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Allow use of the carrier board MicroSD card available in the
Wandboard; this allow for loading alternative system from the other
card for testing or upgrade proposes.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This makes environment and mmcdev/mmcpart in sync with SYS_MMC_ENV_DEV
and SYS_MMC_ENV_PART settings.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Titanium is a i.MX6 based board from ProjectionDesign / Barco. This
patch adds support for this board with the newly introduced NAND
support for i.MX6.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds the fast booting LWMON5 derivat "lcd4_lwmon5".
Its a stripped down version of the full blown lwmon5 support,
without ECC, USB, POST and some other stuff. It used the newly
introduced SPL infrastrucure for SPL from NOR flash booting
on the PPC4xx.
By setting the environment variable "boot_os" to "yes", Linux
will be started from the SPL version. If not, the "normal"
U-Boot will be started.
Signed-off-by: Stefan Roese <sr@denx.de>
Quick manual fixup to merge the USB boot related defines and TPM related
defines.
Conflicts:
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
The ARM errata 742230 - "ARM errata: DMB operation may be faulty" is
claimed for Cortex-A9 (r1p0..r2p2). Though i.MX6 uses a newer revision
than r2p2, we are seeing a reboot failure on i.MX6 SMP build that can be
fixed by applying the workaround for this errata. So for safety, let's
define CONFIG_ARM_ERRATA_742230 to enable the workaround on i.MX6.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Exynos5250 supports secondary USB device boot mode. If the iROM fails
to download u-boot from the primary boot device (such as SD or eMMC),
it will try to retrieve from the secondary boot device (such as USB).
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
this is usefull when writing an UBI image which contains
and UBIFS volume (check README.nand and UBI FAQ for more details)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Since the ICH SPI controller uses PCI, we must ensure that PCI is available
before it is inited.
This fixes the current "ICH SPI: Cannot find device" message on boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Beaver is a Tegra30 board that is nearly 100% compatible w/Cardhu.
Add a Beaver build so it can begin to be differentiated, if need be.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Boot script support brings TEC in line with other Tegra boards. To
enable booting a Linux kernel with initial ramdisk, also include support
for the new FIT image type.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Boot script support brings Plutux in line with other Tegra boards. In
order to enable booting a Linux kernel with initial ramdisk, also add
support for the new FIT image type.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Boot script support brings Medcom-Wide in line with other Tegra boards.
In order to enable booting a Linux kernel with initial ramdisk, also add
support for the new FIT image type.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Some 3rd-party flash tools use the -v (verify) option of crc32 command.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This target wants to check full SPL size, BSS included.
Remove CONFIG_SPL_MAX_SIZE definition and instead define
CONFIG_SPL_MAX_FOOTPRINT.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This target wants to check full SPL size, BSS included.
Remove CONFIG_SPL_MAX_SIZE definition and instead define
CONFIG_SPL_MAX_FOOTPRINT.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This target wants to check full SPL size, BSS included.
Remove CONFIG_SPL_MAX_SIZE definition and instead define
CONFIG_SPL_MAX_FOOTPRINT.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Remove SPL-related ASSERT() in arch/arm/cpu/u-boot.lds
as this file is never used for SPL builds.
Rewrite the ASSERT() in arch/arm/cpu/u-boot-spl.lds
to separately test image (text,data,rodata...) size,
BSS size, and full footprint each against its own max,
and make Tegra boards check full footprint.
Also, output section mmutable is not used in SPL builds.
Remove it.
Finally, update README regarding the (now homogeneous)
semantics of CONFIG_SPL_[BSS_]MAX_SIZE and add the new
CONFIG_SPL_MAX_FOOTPRINT macro.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This enables the device tree library on the Integrator platforms
so we can pass a device tree when booting.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As this board has NAND and supports YAFFS2, add CONFIG_MD_NAND_YAFFS
Cc: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: David Müller <d.mueller@elsoft.ch>
This board is from a u-boot point of view a mixture between kmnusa and
a standard km_kirkwood board. We have our u-boot environment in the spi
NOR flash, but we have a direct connection between the kirkwood and the
piggy. A FPGA is connected via the PCIe interface. So we only have to
select the specific features in the board setup.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
The conversion of mx31pdk to SPL NAND fixed the boot issue, but we start seeing
resets in loop, which prevents us from reaching the U-boot prompt.
Until the proper fix can be identified, disable watchdog, so that mx31pdk
can be functional again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The migration of boards from Makefile to boards.cfg was due for v2012.03, but
smdk6400 did not follow, and it does not build, so move it to scrapyard. It will
still be possible to restore it from the Git history before fixing it.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This also fixes support for mx31pdk and tx25, which had been broken by commit
e05e5de7fa.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Change CONFIG_SPL_PAD_TO from a link address to an image offset since this is
more handy and closer to the purpose of this config.
Automatically define CONFIG_SPL_PAD_TO to CONFIG_SPL_MAX_SIZE (or 0 without
CONFIG_SPL_MAX_SIZE).
Test that CONFIG_SPL_PAD_TO >= CONFIG_SPL_MAX_SIZE if CONFIG_SPL_PAD_TO is
non-zero.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Add support for the Samsung K9LAG08U0M NAND Flash (2-GiB MLC NAND Flash, 2-kiB
pages, 256-kiB blocks, 30-ns R/W cycles, 1 CS) on mx53ard.
eNFC_CLK_ROOT is set up with a cycle time of 37.5 ns (400 MHz / 3 / 5) for this
board, which satisfies the 30-ns NF R/W cycle requirement.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
The function get_timer() should return time in ms and CONFIG_SYS_HZ
should be set to 1000 by default. Fix both of these items.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The current u-boot binary needs more than 128KB of flash space and so
move the u-boot environment from an offset of 128KB to 256KB in flash
to ensure the enviroment does not overlap with u-boot.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
In the current u-boot, the device pin multiplexing and clock
initialisation needs to be early during the boot process and before
board_init() is called. U-boot is currently crashing on this board
because this is not being done early enough. Therefore, add a s_init()
function for the omap5912-osk board to do this.
Also fix the stack pointer so that it is pointing to the end of the
internal RAM and not the beginning as this was also causing the device
to crash.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
- Add CONFIG_DFU_NAND, CONFIG_DFU_MMC
- Set dfu_alt_info_nand, dfu_alt_info_emmc and dfu_alt_info_mmc to show
working examples for those cases.
- Increase CONFIG_SYS_MAXARGS due to hush parsing bugs that would
otherwise disallow 'setenv dfu_alt_info ${dfu_alt_info_nand}'.
- Enable CONFIG_FAT_WRITE to allow updating on MMC
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
drivers/usb/gadget/composite.c requires that this is defined early.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
The omap5_uevm platform has eMMC, and it makes sense to say that our
default env storage shall reside there. Other platforms may not, so
move this choice to the EVM config. In addition, we should provide some
way to partition the flash for later usage, so take advantage of the GPT
partition table support code and allow that to be setup with some
reasonable defaults.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
So with OMAP added to multi platform kernel,
the uImage no more contains a valid load address.
With the uboot already supporting zImage,
change the default boot command to bootz
instead.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
