Commit graph

11612 commits

Author SHA1 Message Date
Enric Balletbo i Serra
ac657c42af ARMV7: OMAP3: Use generic mmc driver on OMAP3 IGEP module
This patch switches from the legacy mmc driver to the new generic mmc driver

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:34:37 -04:00
Enric Balletbo i Serra
f49d7b6cab ARMV7: OMAP3: Use generic mmc driver on IGEP v2
This patch switches from the legacy mmc driver to the new generic mmc driver

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:34:33 -04:00
Alagu Sankar
4a1a06bc8b mmc: Add multi-block read support to the generic mmc driver
This patch adds multi-block read support for the generic MMC
driver. Large reads are broken into chunks of 65535 blocks to
ensure that the code works with controllers having a 16 bit block counter.

This patch results in a significant performance improvement.

Time to read a 45 MB file went from 36 seconds to 9 seconds on Overo

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:25 -04:00
Steve Sakoman
def412b661 mmc: Clean up generic mmc driver multi-block write functions
The current mmc write implementation is type ulong, but returns int values.
Some of the printf's are terminated with /n/r, one has none.

This patch fixes these issues and also removes some unnecessary local
variables.

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:21 -04:00
Steve Sakoman
31bfcf1c57 ARMV7: OMAP: Fix build after introduction of GENERATED_GBL_DATA_SIZE
This patch fixes the issue by defining and using CONFIG_SYS_INIT_RAM_SIZE and
CONFIG_SYS_INIT_RAM_ADDR. Based on an email discussion with Wolfgang Denk and
Heiko Schocher.

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:16 -04:00
Koen Kooi
ca5f80ae97 ARMV7: OMAP3: Add expansion board detection for Beagle
Beagle expansion boards contain an i2c eeprom to identify themselves.
This patch adds code to read and parse the eeprom contents.  It prints
the expansion board name and revision and modifies environment variables
as appropriate. This patch is based on the Overo expansion board code.

Signed-off-by: Koen Kooi <k-kooi@ti.com>
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:11 -04:00
Steve Sakoman
d64b5b8915 ARMV7: OMAP3: Add expansion board detection for Overo
Overo expansion boards contain an i2c eeprom to identify themselves.
This patch adds code to read and parse the eeprom contents.  It prints
the expansion board name and revision and modifies environment variables
as appropriate.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:06 -04:00
Steve Sakoman
8345fb242c ARMV7: Fix build for non-OMAP3 boards
Commit c3d3a54 uses CONFIG_ARMV7 to determine whether to call the
v7_flush_cache_all function.  This breaks the build for all non-OMAP3
boards (like Panda and OMAP4430SDP) since there is only a v7_flush_cache_all
implementation for OMAP3.

This patch uses CONFIG_OMAP3XXX instead of CONFIG_ARMV7 so that only boards
with a v7_flush_cache_all will make the call.

Tested on Beagle, Overo, Panda, and OMAP4430SDP

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:02 -04:00
Steve Sakoman
a711edfae1 ARMV7: OMAP3: IGEP: Rename TEXT_BASE
Commit 14d0a02a "Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE" missed the
IGEP boards since they were just added.

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:26:57 -04:00
Reinhard Meyer
7d44af08b8 AT91: add header file for the Shutdown Controller
and SHDWN address entry in at91sam9260.h

Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-11-02 09:47:13 +01:00
Reinhard Meyer
33825ec1a4 AT91: add 2nd SPI to 9260/9XE/9G20
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-30 10:20:46 +02:00
Stefano Babic
590084a2f7 env_sf: remove warning introduced with last patch
Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-29 23:07:59 +02:00
Wolfgang Denk
0c0892be0d Merge branch 'master' of git://git.denx.de/u-boot-marvell
Conflicts:
	include/configs/km_arm.h

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-29 22:03:00 +02:00
Wolfgang Denk
d75c2a3d7f Merge branch 'master' of git://git.denx.de/u-boot-imx 2010-10-29 21:50:24 +02:00
Wolfgang Denk
17dd883c5b Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-10-29 21:47:48 +02:00
Wolfgang Denk
3388db2cd7 Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2010-10-29 21:46:08 +02:00
Wolfgang Denk
1ecb758341 Merge branch 'for-wd-master' of git://git.denx.de/u-boot-pxa 2010-10-29 21:44:40 +02:00
Wolfgang Denk
e03f316974 Drop support for CONFIG_SKIP_RELOCATE_UBOOT
For ARM systems, before ELF relocation was introduced,
CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the
U-Boot image from whereever it was loaded to it's link address
(CONFIG_SYS_TEXT_BASE).  The name was badly chosen, as no relocation
was performed at all, it was just a memcpy().

With ELF relocation, this does not work like that any more, and
related boards need to be fixed anyway.  So don't keep this relict any
longer.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:40:08 +02:00
Wolfgang Denk
a9aa392629 Drop support for CONFIG_SYS_ARM_WITHOUT_RELOC
When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support.  However, other recent changes led to a different
implementation (ELF relocation), where this no longer works.  By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.

So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:39:59 +02:00
Wolfgang Denk
2e5167ccad Replace CONFIG_RELOC_FIXUP_WORKS by CONFIG_NEEDS_MANUAL_RELOC
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:32:07 +02:00
Tanmay Upadhyay
28e57108a6 Kirkwood: bugfix: DRAM size initialization
If start of any DRAM bank is greater than total DDR size, remaining DDR banks' start address & size were left un-initialized in dram_init function. This could break other functions who uses array 'gd->bd->bi_dram'. Kirkwood network driver is one example. This also stops Linux kernel from booting.

v2 - Set start address also to 0. Without this Linux kernel couldn't
     boot up

Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
2010-10-28 20:06:22 +05:30
Prafulla Wadaskar
31d80c77ff kirkwood: get rid of config.mk files
After moving the definition of CONFIG_SYS_TEXT_BASE to the respective
board config files, all Marvell kirkwood board have just a single and
common entry in their config.mk files:

	KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg

Replace the only reference to KWD_CONFIG in the top level Makefile by
an equivalent setting, and remove all kirkwood config.mk files.

Signed-off-by: Wolfgang Denk <wd at denx.de>
Cc: Prafulla Wadaskar <prafulla at marvell.com>
Cc: Siddarth Gore <gores at marvell.com>
Cc: Simon Kagstrom <simon.kagstrom at netinsight.net>
Cc: Heiko Schocher <hs at denx.de>
Cc: Eric Cooper <ecc at cmu.edu>
Acked-by: Wolfgang Denk <wd at denx.de>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-10-28 19:12:06 +05:30
Gray Remlin
5842383e25 kirkwood: guruplug: Relocate NAND environment area
Current default options increase u-boot size to overlap the location of the environment in NAND, move environment higher up

Signed-off-by: Gray Remlin <g_remlin@rocketmail.com>
2010-10-28 19:02:12 +05:30
Shawn Guo
1ab027cbf6 mx51evk: support new relocation scheme
This patch is to fix build breakage and support new relocation
scheme for mx51evk.

- Correct IRAM base address and add size definition

  The IRAM starts from 0x1FFE0000 on final revsion i.mx51 than
  0x1FFE8000 which is for older revision.

- Include imx-regs.h in mx51evk.h

  Definitions like CSD0_BASE_ADDR and IRAM_BASE_ADDR can be
  referred to.

- Define CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE

  They are used to define init RAM layout.

- Remove comment for CONFIG_SYS_GBL_DATA_SIZE which has been
  buried by Wolfgang's commit below

  25ddd1fb: Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value

Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
2010-10-28 11:43:23 +02:00
Shawn Guo
06982534b6 mx51evk: consolidate env for mmcboot and netboot
This patch is to consolidate default mx51evk env for two primary
boot modes, mmcboot and netboot.

It also cleans some unused env like netdev, uboot and redundant
env like loadaddr since CONFIG_LOADADDR already defines it.

Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
2010-10-28 11:42:45 +02:00
Shawn Guo
888b4f435f mx51evk: Fix 2 hours reset issue
The mx51evk u-boot has an issue that system will get reset
every 2 hours.

MC13892 has an inside charge timer which expires in 120 minutes.
If ICHRG and CHGAUTOB are not set properly, this timer expiration
will get system power recycled.

Since mx51evk has no Li-Ion battery on board, the patch sets
ICHRG in externally powered mode and sets CHGAUTOB bit to avoid
automatic charging, so that system will not get reset by this
timer expiration.

The patch also corrects the bit field definition of register 48
(Charger 0) per latest MC13892 Reference Manual.

Signed-off-by: Shawn Guo <shawn.gsc@gmail.com>
2010-10-28 11:42:34 +02:00
Stefano Babic
9a0044183a MX51: remove warning in clock.c
The patch removes the warning:

clock.c:291: warning: initialization from incompatible pointer type

after  constification of args[]

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-28 11:08:52 +02:00
Matthias Weisser
81129d07a0 imx25: Fix reset
This patch fixes the reset command on imx25. The watchdog registers are 16
bits in size and not 32. This patch also adds the service register codes as
constants.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2010-10-28 10:32:21 +02:00
Jason Liu
95707aaa9e MX5:use common u-boot.lds of cpu layer
Remove u-boot.lds from mx5 and use the common u-boot.lds
of cpu layer. This patch also fix the building errors:

arch/arm/cpu/armv7/start.o: In function `_rel_dyn_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_start'
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_end_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_end'
arch/arm/cpu/armv7/start.o: In function `_dynsym_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__dynsym_start'

Signed-off-by: Jason Liu <r64343@freescale.com>
2010-10-28 10:32:20 +02:00
Stefano Babic
51fd9a7e01 MX51: add CONFIG_SYS_TEXT_BASE to vision2 board, use general ld script
Recent patch changed TEXT_BASE to CONFIG_SYS_TEXT_BASE and
vision2 board was not updated.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-28 10:32:20 +02:00
C Nauman
d9abba8254 Add generic support for samsung s3c2440
This patch adds generic support for the Samsung s3c2440 processor.

Global s3c24x0 changes to struct members converting from upper case to
lower case.

Signed-off-by: Craig Nauman <cnauman@diagraph.com>
Cc: kevin.morfitt@fearnside-systems.co.uk
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-10-28 15:35:56 +09:00
Mike Frysinger
73520939b4 Blackfin: config.mk: drop manual stripping of config vars
Now that the common code takes care of stripping away quotes and such
from numeric options, we no longer need to do so ourselves.  So drop
the custom code we have in the Blackfin config.mk.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-27 21:18:05 -04:00
Mike Frysinger
1fde3eb2d3 Blackfin: fix building after asm-offsets.h intro
Since some of the defines in our config.h use the generated defines, we
need to include the generated header.  This fixes building of the Blackfin
start.S file (where the stack is setup).

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-27 21:10:58 -04:00
Mikhail Kshevetskiy
9b8081a452 arm/pxa: remove unused arch-pxa/macro.h
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
2010-10-27 23:59:53 +02:00
Wolfgang Denk
908614f20f Prepare v2010.12-rc1
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-27 22:49:13 +02:00
Wolfgang Denk
071bc92330 Coding Style cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-27 22:48:30 +02:00
Enric Balletbo i Serra
57ff9f2421 cmd_onenand.c: Fix command usage help.
Running the onenand command without arguments does nothing, with this
patch shows the command usage.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2010-10-27 20:51:22 +02:00
Lei Wen
0158126e25 mmc: seperate block number into small parts for multi-write cmd
Constraint the mmc framework to only send no more than 65535
blocks in one go during the multi-write command. This constraint
comes due to the limitation of 16bit width block counter register
at some hardware.

Signed-off-by: Lei Wen <leiwen@marvell.com>
Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-27 20:39:33 +02:00
Wolfgang Denk
73bb4c7240 Merge branch 'master' of git://git.denx.de/u-boot-sparc 2010-10-27 20:37:33 +02:00
Stefano Babic
a3110f01c4 env_sf: updated to the new environment code
Functions to store/retrieve the environment from a SPI flash was not updated
to the new environment code. The non-redundant case was
not working correctly, reporting ""Environment SPI flash not initialized"
and the code was not compiled clean in the redundant case.

The patch fixes these issue and makes the code more coherent
with other environment storage (nand, flash).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-27 20:30:23 +02:00
Wolfgang Denk
f0fee6a646 Makefile: fix dependencies for building NAND_SPL
Building of NAND based boards failed sometimes (especially on MP
systems) because of incorrect / missing dependencies.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
2010-10-27 20:18:34 +02:00
Wolfgang Denk
e4691f5ed1 make-asm-offsets: fix sed script
When copying the "sed" script to generate the asm-offsets.h file from
the Linux Kbuild script into the make-asm-offsets file I missed the
fact that the former runs in a "make" context and thus uses double
"$$" to escape a single "$", while the latter is a shell script, where
this must not be done.  Unfortunately the problem did not show up
during the initial tests on Power Architecture systems, but on ARM the
generated asm-offsets.h was not correct.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
2010-10-27 20:16:52 +02:00
Wolfgang Denk
f503d52a9e mcu25: fix out of tree building
Out of tree building of the Netstal mcu25 board failed like
that:

Configuring for mcu25 board...
Assembler messages: Fatal error: can't create /work/wd/tmp-ppc/board/netstal/mcu25/../common/fixed_sdram.o: No such file or directory
Assembler messages: Fatal error: can't create /work/wd/tmp-ppc/board/netstal/mcu25/../common/nm_bsp.o: No such file or directory

Adapt (and simplify) the Makefile.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
2010-10-27 20:13:46 +02:00
Wolfgang Denk
ec5c04cdb5 Revert "cmd_net: drop spurious comma in U_BOOT_CMD"
This commit causes build errors like this:

cmd_net.c:301:1: error: macro "U_BOOT_CMD" requires 6 arguments, but only 5 given
cmd_net.c:298: warning: data definition has no type or storage class
cmd_net.c:298: warning: type defaults to 'int' in declaration of 'U_BOOT_CMD'

This reverts commit 8f4cb77ef7.
2010-10-27 20:13:46 +02:00
Wolfgang Denk
8343f8a764 post/drivers/i2c.c: fix compile error
Commit 7e263ce "post/i2c: Clean up detection logic" added a "const"
qualifier to the declaration of i2c_addr_list[], missing the fact that
the list gets modified later in the code, which results in build
errors like these:

i2c.c: In function 'i2c_post_test':
i2c.c:88: error: assignment of read-only location

Remove the incorrect "const".

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2010-10-27 20:09:59 +02:00
Wolfgang Denk
79e6313936 ARM: use the same branch insn on all architectures
For the "fixloop" implementation in start.S a number of different
instructions was used.  Unify code so all architectures use "blo"
here because it is more robust in case of incorrect alignments.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.aribaud@free.fr>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
2010-10-26 21:19:19 +02:00
Sughosh Ganu
f760d14acc Remove config.mk for da8xxevm based boards.
Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the
now unnecessary config.mk file.

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
2010-10-26 21:17:24 +02:00
Heiko Schocher
1336cad298 arm, bootm: Fix compile warning
Fix warning:

bootm.c: In function 'bootm_linux_fdt':
bootm.c:181: warning: unused variable 's'
bootm.c:180: warning: unused variable 'bd'

Signed-off-by: Heiko Schocher <hs@denx.de>
2010-10-26 21:15:35 +02:00
Mike Frysinger
8f4cb77ef7 cmd_net: drop spurious comma in U_BOOT_CMD
Building for boards that have CONFIG_CMD_CDP enabled fail with:
cmd_net.c:301: error: expected expression before ',' token

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-26 21:14:55 +02:00
Darius Augulis
ea34c9d6ed arm1176: fix relocation
Fix relocation code for arm1176, do it like other ARM
CPU's are doing.
Tested only with CONFIG_SKIP_RELOCATE_UBOOT defined
and using nand_spl (booting from nand). Test done on
s3c6410 based board (not yet supported in main line).

Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
2010-10-26 21:12:53 +02:00