Commit graph

15 commits

Author SHA1 Message Date
Simon Glass
e3563f2ec7 mmc: Support bypass mode with the get_mmc_clk() method
Some SoCs want to adjust the input clock to the DWMMC block as a way of
controlling the MMC bus clock. Update the get_mmc_clk() method to support
this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-09-02 21:28:23 -06:00
Masahiro Yamada
0f9258228e of: clean up OF_CONTROL ifdef conditionals
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL.  We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:

 #ifdef CONFIG_OF_CONTROL
 # if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
 #  define OF_CONTROL 0
 # else
 #  define OF_CONTROL 1
 # endif
 #else
 # define OF_CONTROL 0
 #endif

Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute.  It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.

Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-18 13:46:05 -04:00
Przemyslaw Marczak
64029f7aee mmc: exynos dwmmc: check boot mode before init dwmmc
Before this commit, the mmc devices were always registered
in the same order. So dwmmc channel 0 was registered as mmc 0,
channel 1 as mmc 1, etc.
In case of possibility to boot from more then one device,
the CONFIG_SYS_MMC_ENV_DEV should always point to right mmc device.

This can be achieved by init boot device as first, so it will be
always registered as mmc 0. Thanks to this, the 'saveenv' command
will work fine for all mmc boot devices.

Exynos based boards usually uses mmc host channels configuration:
- 0, or 0+1 for 8 bit  - as a default boot device (usually eMMC)
- 2 for 4bit - as an optional boot device (usually SD card slot)

And usually the boot order is defined by OM pin configuration,
which can be changed in a few ways, eg.
- Odroid U3     - eMMC card insertion -> first boot from eMMC
- Odroid X2/XU3 - boot priority jumper

By this commit, Exynos dwmmc driver will check the OM pin configuration,
and then try to init the boot device and register it as mmc 0.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
2015-02-23 19:49:22 +02:00
Jaehoon Chung
5dab81cea5 mmc: exynos_dw_mmc: use the exynos specific data structure
Clksel value is exynos specific value.
It removed "clksel_val" into dwmci_host and created the
"dwmci_exynos_priv_data" structure for exynos specific data.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-02-23 19:39:51 +02:00
Jaehoon Chung
3a33bb1874 mmc: exynos_dw_mmc: set to clksel_val into board-init function
"clksel_val" is assigned to property of mmc or defined value.
But it doesn't write at initial sequence.
There is a reason that get the wrong source-clock value.
This patch fixed it.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-02-23 19:36:55 +02:00
Jaehoon Chung
dfcb683a31 mmc: exynos_dw-mmc: change debug message
To debug more exactly, add the index for device.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2014-12-12 20:35:30 +02:00
Jaehoon Chung
e09bd85329 mmc: exynos_dw_mmc: enable the DDR mode
Set the ddr mode capability by default.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Jaehoon Chung
959198f7ca mmc: exynos_dw_mmc: restore the property into host
Restore the platdata(property of dt) into host struct.
Then data's information is maintained and reused anywhere.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16 14:54:26 +09:00
Rajeshwari S Shinde
d3e016cc28 MMC: DWMMC: Correct the CLKDIV register value
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)

Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.

This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 17:42:26 +02:00
Jaehoon Chung
18ab675597 mmc: dw_mmc: remove the exynos specific code in dw-mmc.c
dw-mmc.c is the general driver file.
So, remove the exynos specific code at dw-mmc.c.
Instead, exynos specific cod can be move into exynos-dw_mmc.c.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2013-12-08 14:07:07 +02:00
Rajeshwari Shinde
6f0b7caa67 DWMMC: SMDK5420: Disable SMU for eMMC
SMDK5420 has a new Security Management Unit added
for dwmmc driver, hence, configuring the control
registers to support booting via eMMC.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31 09:55:33 +02:00
Jaehoon Chung
b44fe83a58 mmc: dw_mmc: change the callback function name.
To prevent the confusion, use the get_mmc_clk() instead of mmc_clk().
get_mmc_clk() is more exactly name.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2013-10-31 09:55:33 +02:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Amar
a082a2dde0 EXYNOS5: DWMMC: Added FDT support for DWMMC
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-13 17:35:14 +09:00
Jaehoon Chung
d0ebbb8dfa EXYNOS: mmc: support DesignWare Controller for Samsung-SoC
Support DesignWare MMC Controller for Samsung Specific.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Rajeshawari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 17:26:47 -06:00