Commit graph

55 commits

Author SHA1 Message Date
Tom Rini
219f4788d3 hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-06-20 20:36:51 +02:00
Timur Tabi
3b6b256c43 powerpc/83xx: increment malloc heap size for the MPC832x MDS boards
The malloc buffer is not large enough to hold a flash sector (0x20000 bytes)
in addition to whatever else it normally holds, so double its size.  This
fixes a failure trying to save the environment:

=> save
Saving Environment to Flash...
Unable to save the rest of sector (122880)
. done
Protected 1 sectors

This problem probably surfaced from some other change that significantly
increased the normal memory usage, thereby not leaving enough room for
the saveenv command.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-06-15 16:42:32 -05:00
Joe Hershberger
7d6a098219 mpc83xx: Cleanup usage of LBC constants
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:56 -05:00
Joe Hershberger
2fef402097 mpc83xx: Cleanup usage of DDR constants
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:55 -05:00
Joe Hershberger
72cd4087c9 mpc83xx: Cleanup usage of BAT constants
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:55 -05:00
Joe Hershberger
989091acb0 mpc83xx: cosmetic: MPC832XEMDS.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:53 -05:00
Mike Frysinger
31a4f1e5b6 board configs: drop NET_MULTI references
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00
Andy Fleming
865ff85640 fsl: Change fsl_phy_enet_if to phy_interface_t
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:35 -05:00
Wolfgang Denk
25ddd1fb0a Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:05:30 +02:00
Wolfgang Denk
553f09823c Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE
CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE

No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.

Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken.  Last known maintainers on Cc:

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:03:25 +02:00
Peter Tyser
d98b0523cf powerpc: Cleanup BOOTFLAG_* references
Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.

Note that this change makes the board info bd_bootflags field useless.
It will always be set to 0, but we leave it around so that we don't
break the board info structure that some OSes are expecting to be passed
from U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-18 22:38:56 +02:00
Wolfgang Denk
2ae1824196 Makefile: move all Power Architecture boards into boards.cfg
Clean up Makefile, and drop a lot of the config.mk files on the way.

We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:12:04 +02:00
Wolfgang Denk
14d0a02a16 Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:07:10 +02:00
Ira W. Snyder
9f530d59e6 e300: increase CONFIG_SYS_BOOTMAPSZ to allow booting large kernels
Newer Linux kernels can overrun the initial memory window used for
booting with their BSS area. When this happens, they overwrite the FDT
and silently fail to boot.

On e300 CPUs, the Linux kernel uses an initial BAT covering the first
256MB of RAM. See arch/powerpc/kernel/head_32.S for details. Increase
the value of CONFIG_SYS_BOOTMAPSZ to accommodate the maximum value
allowed by Linux. This will allow very large kernels to boot.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-09-23 21:13:32 +02:00
Stefan Roese
24956642ef Remove unused CONFIG_SERIAL_SOFTWARE_FIFO feature
This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2010-09-23 09:02:05 +02:00
Kim Phillips
78b7a8ef8b net: rename "FSL UECx" net interfaces "UECx"
continuation of commit 2ecc2262d66a286e3aac79005bcb5f461312dea8
"net ppc: fix ethernet device names with spaces" (currently in
u-boot-net.git) for QE based parts.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09 11:52:29 -07:00
Kim Phillips
1a2e203b31 mpc83xx: turn on icache in core initialization to improve u-boot boot time
before, MPC8349ITX boots u-boot in 4.3sec:

        column1 is elapsed time since first message
        column2 is elapsed time since previous message
        column3 is the message
0.000 0.000: U-Boot 2010.03-00126-gfd4e49c (Apr 11 2010 - 17:25:29) MPC83XX
0.000 0.000:
0.000 0.000: Reset Status:
0.000 0.000:
0.032 0.032: CPU:   e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.032 0.000: Board: Freescale MPC8349E-mITX
0.032 0.000: UPMA:  Configured for compact flash
0.032 0.000: I2C:   ready
0.061 0.028: DRAM:  256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
1.516 1.456: FLASH: 16 MB
2.641 1.125: PCI:   Bus Dev VenId DevId Class Int
2.652 0.011:         00  10  1095  3114  0180  00
2.652 0.000: PCI:   Bus Dev VenId DevId Class Int
2.652 0.000: In:    serial
2.652 0.000: Out:   serial
2.652 0.000: Err:   serial
2.682 0.030: Board revision: 1.0 (PCF8475A)
3.080 0.398: Net:   TSEC1: No support for PHY id ffffffff; assuming generic
3.080 0.000: TSEC0, TSEC1
4.300 1.219: IDE:   Bus 0: .** Timeout **

after, MPC8349ITX boots u-boot in 3.0sec:

0.010 0.010: U-Boot 2010.03-00127-g4b468cc-dirty (Apr 11 2010 - 17:47:29) MPC83XX
0.010 0.000:
0.010 0.000: Reset Status:
0.010 0.000:
0.017 0.007: CPU:   e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.017 0.000: Board: Freescale MPC8349E-mITX
0.038 0.020: UPMA:  Configured for compact flash
0.038 0.000: I2C:   ready
0.038 0.000: DRAM:  256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
0.260 0.222: FLASH: 16 MB
1.390 1.130: PCI:   Bus Dev VenId DevId Class Int
1.390 0.000:         00  10  1095  3114  0180  00
1.390 0.000: PCI:   Bus Dev VenId DevId Class Int
1.400 0.010: In:    serial
1.400 0.000: Out:   serial
1.400 0.000: Err:   serial
1.400 0.000: Board revision: 1.0 (PCF8475A)
1.832 0.432: Net:   TSEC1: No support for PHY id ffffffff; assuming generic
1.832 0.000: TSEC0, TSEC1
3.038 1.205: IDE:   Bus 0: .** Timeout **

also tested on these boards (albeit with a less accurate
boottime measurement method):

seconds: before  after
8349MDS  ~2.6    ~2.2
8360MDS  ~2.8    ~2.6
8313RDB  ~2.5    ~2.3 #nand boot
837xRDB  ~3.1    ~2.3

also tested on an 8323ERDB.

v2: also remove the delayed icache enablement assumption in arch ppc's
board.c, and add a CONFIG_MPC83xx define in the ITX config file for
consistency (even though it was already being defined in 83xx'
config.mk).

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-04-22 18:44:56 -05:00
Kim Phillips
a059e90e16 mpc83xx: enable command line autocompletion
because it's convenient.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-04-22 18:34:49 -05:00
Kim Phillips
ecd1a09b81 mpc83xx: remove hardcoded network addresses from config files
and avoid e.g., two identical boards from causing random networking
conflicts when hooked up to the same network.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-02-22 16:48:06 -06:00
Heiko Schocher
582c55a027 83xx, uec: split enet_interface in two variables
There's no sensible reason to unite speed and interface type into
one variable.  So split this variable enet_interface into two
vars: enet_interface_type, which hold the interface type and speed.

Also: add the possibility for switching between 10 and 100 MBit
interfaces on the fly, when running in FAST_ETH mode.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:37:12 -08:00
Kim Phillips
c7190f028f mpc83xx: retain POR values of non-configured ACR, SPCR, SCCR, and LCRR bitfields
some LCRR bits are not documented throughout the 83xx family RMs.
New board porters copying similar board configurations might omit
setting e.g., DBYP since it was not documented in their SoC's RM.

Prevent them bricking their board by retaining power on reset values
in bit fields that the board porter doesn't explicitly configure
via CONFIG_SYS_<registername>_<bitfield> assignments in the board
config file.

also move LCRR assignment to cpu_init_r[am] to help ensure no
transactions are being executed via the local bus while CLKDIV is being
modified.

also start to use i/o accessors.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-09-26 21:19:38 -05:00
Kim Phillips
79f516bccc mpc83xx: accommodate larger kernel sizes by default
linux mpc83xx_defconfig kernels are getting bigger, accommodate for
their growth by adjusting default load and fdt addresses.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-08-21 17:11:44 -05:00
Kim Phillips
be9b56df02 mpc83xx: CONFIG_83XX_GENERIC_PCI is now synonymous with CONFIG_PCI; remove the former
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-27 10:17:54 -05:00
Kim Phillips
9993e196da mpc83xx: convert all remaining boards over to 83XX_GENERIC_PCI
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-18 19:43:04 -05:00
Kim Phillips
4a9932a436 mpc83xx: increase MONITOR_LEN to offset growing pains
Saving the environment leads to overwriting u-boot itself,
bricking boards.  Increase u-boot's image size so the environment
base address doesn't end up overlapping u-boot text.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-14 14:58:39 -05:00
Peter Tyser
2c7920afaf 83xx: Replace CONFIG_MPC83[0-9]X with MPC83[0-9]x
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-06-12 20:47:17 +02:00
Peter Tyser
0f89860494 83xx: Replace CONFIG_MPC83XX with CONFIG_MPC83xx
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-06-12 20:47:17 +02:00
Kumar Gala
540dcf1cb8 83xx: Use common LSDMR defines from asm/fsl_lbc.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
2009-03-30 13:33:49 -05:00
Mike Frysinger
bdab39d358 rename CONFIG_CMD_ENV to CONFIG_CMD_SAVEENV
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment.  So, let's make sure the define is named accordingly.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-18 00:47:43 +01:00
Jerry Van Baren
ae0b05df04 Fix whitespace damage: double space changed to a tab
At some point an intentional double space at the end of the sentence
got changed into a tab in the GPL header line:
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

This patch fixes the damage.

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2009-02-11 23:03:41 +01:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Kim Phillips
162c41c031 mpc83xx: add h/w flash protection to board configs
the operating system may leave flash in a h/w locked state after writing.
This allows u-boot to continue to write flash by enabling h/w unlocking
by default.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-09-24 09:58:34 -05:00
Jean-Christophe PLAGNIOL-VILLARD
0e8d158664 rename CFG_ENV macros to CONFIG_ENV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:06 +02:00
Jean-Christophe PLAGNIOL-VILLARD
5a1aceb068 rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
93f6d72544 rename CFG_ENV_IS_NOWHERE in CONFIG_ENV_IS_NOWHERE
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:00 +02:00
Jean-Christophe PLAGNIOL-VILLARD
00b1883a4c drivers/mtd: Move conditional compilation to Makefile
rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:42 +02:00
Becky Bruce
31d8267224 PPC: Create and use CONFIG_HIGH_BATS
Change all code that conditionally operates on high bat
registers (that is, BATs 4-7) to look at CONFIG_HIGH_BATS
instead of the myriad ways this is done now.  Define the option
for every config for which high bats are supported (and
enabled by early boot, on parts where they're not always
enabled)

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-03 17:48:41 +02:00
Wolfgang Denk
53677ef18e Big white-space cleanup.
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-21 00:14:08 +02:00
Kim Phillips
b211575740 mpc83xx: bump loadaddr over fdtaddr to 0x500000
this seems as a good compromise between human memory, typing,
and last but not least, to accommodate for current and future kernel bloat.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
2008-04-25 10:54:06 -05:00
Scott Wood
a7ba32d480 mpc83xx: Set PCI I/O bus-address base to zero.
The device trees for these boards describe PCI I/O as starting from
address zero from the device's perspective.

Placing I/O elsewhere may cause problems with certain PCI boards, and may
cause problems with Linux.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-03-25 19:16:48 -05:00
Kim Phillips
270fe261b7 mpc83xx: make dtb basename file references equal those of linux
the dts file basenames were updated in linux - this helps avoid
inadvertently loading any old dtbs laying around.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-03-07 12:47:11 -06:00
Timur Tabi
73bf1e2de7 Remove #undef DEBUG from MPC83xx board header files
Remove the "#undef DEBUG" line from all Freescale 83xx board header files.
The inclusion of this line makes it impossible to enable debug code in
other source files, because "#define DEBUG" typically needs to be defined
before any header files are included.

Signed-off-by: Timur Tabi <timur@freescale.com>
2008-02-12 00:39:45 +01:00
Kim Phillips
711a794627 mpc83xx: fix QE ETHPRIMEs to correct 'FSL UEC0' value
continuation of commit b96c83d4ae

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16 12:00:50 -06:00
Dave Liu
2c5b48fc20 mpc83xx: Remove cache config from config.h
clean up the cache config from configs.h of board

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-10 21:06:32 -06:00
Kim Phillips
977b57583a mpc83xx: add missing CONFIG_HAS_ETH0 defines
the new libfdt code only updates eth0 if CONFIG_HAS_ETH0
is defined; add the define to the missing board configs.

Thanks to Emilian Medve for finding this.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-10 20:52:38 -06:00
Kim Phillips
5b8bc606c6 mpc83xx: convert to using do_fixup_*()
convert to using simpler mpc85xx style fdt update code; streamline by
eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm
the old school FLAT_TREE code from 83xx (since the sbc8349 was just
converted over to using libfdt).

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-08 09:56:42 -06:00
Timur Tabi
b2893e1fcb 83xx: fix CFG_ENV_ADDR and CFG_ENV_SECT_SIZE definitions
Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for all of the
currently-defined 83xx boards.  This change guarantees that the environment
will be located on the first flash sector after the U-Boot image.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-08 09:55:39 -06:00
Kim Phillips
3bb342fc85 fdt: remove unused OF_FLAT_TREE_MAX_SIZE references
and make some minor corrections to the FDT part of the README.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-08-29 01:46:25 +02:00
Tony Li
14778585d1 mpc83xx: Split PIB init code from pci.c and add Qoc3 ATM card support
The patch split the PIB init code from pci.c to a single file board/freescale/common/pq-mds-pib.c
And add Qoc3 ATM card support for MPC8360EMDS and MPC832XEMDS board.

Signed-off-by Tony Li <tony.li@freescale.com>
2007-08-16 23:12:11 -05:00
Kim Phillips
35cc4e4823 mpc83xx: enable libfdt by default on freescale boards
this enables libfdt code by default for the
freescale mpc8313erdb, mpc832xemds, mpc8349emds,
mpc8349itx and gp boards.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-08-15 22:36:33 -05:00