This adds a driver for the SPI controller found on most AT91 and AVR32
chips, implementing the new SPI API.
Changed in v4:
- Update to new API
- Handle zero-length transfers appropriately. The user may send a
zero-length SPI transfer with SPI_XFER_END set in order to
deactivate the chip select after a series of transfers with chip
select active. This is useful e.g. when polling the status
register of DataFlash.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
If the specified delay is very short, the cycle counter may go past the
"end" time we are waiting for before we get around to reading it.
Fix it by checking the different between the cycle count "now" and the
cycle count at the beginning. This will work as long as the delay
measured in number of cycles is below 2^31.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Remove #ifdef CONFIG_MMC from the source file and use conditional
compilation in the Makefile instead.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Make sure we check for CRC errors when sending commands that use CRC
checking.
Reported-by: Gururaja Hebbar K R <gururajakr@sanyo.co.in>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This cleans up the SDRAM initialization and related code a bit, and
allows faster booting.
* Add definitions for EBI and internal SRAM to asm/arch/memory-map.h
* Remove memory test from sdram_init() and make caller responsible
for verifying the SDRAM and determining its size.
* Remove base_address member from struct sdram_config (was sdram_info)
* Add data_bits member to struct sdram_config and kill CFG_SDRAM_16BIT
* Add support for a common STK1000 hack: 16MB SDRAM instead of 8.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Don't do a stack dump if the stack pointer is outside the memory area
reserved for stack.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Since the reset vector is always aligned to a very large boundary, we
can save a couple of KB worth of alignment padding by placing the
exception vectors at the same address.
Deciding which one it is is easy: If we're handling an exception, the
CPU is in Exception mode. If we're starting up after reset, the CPU is
in Supervisor mode. So this adds a very minimal overhead to the reset
path (only executed once) and the exception handling path (normally
never executed at all.)
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
pm_init() was always more about clock initialization than anything
else. Dealing with PLLs, clock gating and such is also inherently
SoC-specific, so move it into a SoC-specific directory.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The .flashprog section was only needed back when we were running
directly from flash, and it's even more useless on NGW100 since it
uses the CFI flash driver which never used this workaround in the
first place.
Remove it on STK1000 as well, and get rid of all the associated code and
annotations.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch forces the watchdog off in all cases. That will at least
get rid of the constant reboot cycle, though it won't let the watchdog
actually run in the new kernels: its probe() comes up with a polite
warning.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The existing code assumes the SDRAM row refresh period should always
be 15.6 us. This is not always true, and indeed on the ATNGW100, the
refresh rate should really be 7.81 us.
Add a refresh_period member to struct sdram_info and initialize it
properly for both ATSTK1000 and ATNGW100. Out-of-tree boards will
panic() until the refresh_period member is updated properly.
Big thanks to Gerhard Berghofer for pointing out this issue.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
As reported by Gerhard Berghofer:
in "gpio_enable_usart3" the correct pins for USART 3 are PB17 and PB18
instead of PB18 and PB19.
which is obviously correct. There's currently no code that uses
USART3, but custom boards may run into problems.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Add a chip-features file providing definitions of the form
AT32AP700x_CHIP_HAS_<peripheral>
to indicate the availability of the given peripheral on the currently
selected chip.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The SoC-specific code for all the AT32AP700x CPUs is practically
identical; the only difference is that some chips have less features
than others. By doing this rename, we can add support for the AP7000
derivatives simply by making some features conditional.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Calculate the data timeout based on values from the CSD instead of
just using a hardcoded DTOR value. This is a backport of a similar fix
in BSP 2.0, with one additional fix: the DTOCYC value is rounded up
instead of down.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
include/asm-avr32/div64.h was recently moved to include/div64.h, but
cpu/at32ap/interrupts.c wasn't properly updated (an earlier version of
the patch was merged perhaps?)
This patch updates cpu/at32ap/interrupts.c so that the avr32 port
compiles again.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Instead of always using the largest blocksize the card supports, check
if it can support smaller block sizes and use 512 bytes if possible.
Most cards do support this, and other parts of u-boot seem to have
trouble with block sizes different from 512 bytes.
Also enable underrun/overrun protection.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Driver for the Atmel MCI controller (MMC interface) for AT32AP CPUs.
The AT91 ARM-based CPUs use basically the same hardware, so it should
be possible to share this driver, but no effort has been made so far.
Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement functions for configuring the mmci pins, as well as
functions for getting the clock rate of the mmci controller.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement functions for configuring the macb0 and macb1 pins, as
well as functions for getting the clock rate of the various
busses the macb ethernet controllers are connected to.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Relocate the u-boot image into SDRAM like everyone else does. This
means that we can handle much larger .data and .bss than we used to.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Rewrite the resource management code (i.e. I/O memory, clock gating,
gpio) so it doesn't depend on any global state. This is necessary
because this code is heavily used before relocation to RAM, so we
can't write to any global variables.
As an added bonus, this makes u-boot's memory footprint a bit smaller,
although some functionality has been left out; all clocks are enabled
all the time, and there's no checking for gpio line conflicts.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Split the avr32 initialization code into a function to run before
relocation, board_init_f and a function to run after relocation,
board_init_r. For now, board_init_f simply calls board_init_r
at the end.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Patch by Haavard Skinnemoen, 06 Sep 2006
This patch adds support for the AT32AP CPU family and the AT32AP7000
chip, which is the first chip implementing the AVR32 architecture.
The AT32AP CPU core is a high-performance implementation featuring a
7-stage pipeline, separate instruction- and data caches, and a MMU.
For more information, please see the "AVR32 AP Technical Reference":
http://www.atmel.com/dyn/resources/prod_documents/doc32001.pdf
In addition to this, the AT32AP7000 chip comes with a large set of
integrated peripherals, many of which are shared with the AT91 series
of ARM-based microcontrollers from Atmel. Full data sheet is
available here:
http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Hans-Christian Egtvedt
Haavard Skinnemoen
David Brownell
Haavard Skinnemoen
Wolfgang Denk
Wolfgang Denk