Commit graph

15 commits

Author SHA1 Message Date
Shaohui Xie
f7c38cf827 phylib: add support for aquantia PHYs
This patch supports AQ1202, AQ2104, AQR105 PHY.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-16 09:32:11 -08:00
Shengzhou Liu
9b18e5199e net/phy: Add support for CS4315/CS4340 PHY
Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
  to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
  we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:11 -08:00
Masahiro Yamada
368b4d2b49 drivers: net: remove dead drivers
The following configs are not defined at all:

 - CONFIG_INCA_IP_SWITCH
 - CONFIG_PBL2800_ETHER
 - CONFIG_PHY_ICPLUS

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-21 12:01:11 -04:00
Masahiro Yamada
e32459e24a drivers: net: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-10-31 13:22:13 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Yegor Yefremov
0fae25089d net: add ICPlus PHY driver
The driver code was taken from Linux kernel source:
drivers/net/phy/icplus.c

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2013-06-24 19:07:32 -05:00
Matt Porter
f485c8a35b phy: add support for ET1011C phys
Adds an ET1011C PHY driver which is derived from the
Linux kernel PHY driver (drivers/net/phy/et1011c.c)
from the v3.9-rc2 tag. Note that an errata workaround
config option is implemented to allow for TX_CLK to be
enabled even when gigabit mode is negotiated. This
workaround is used on the PG1.0 TI814X EVM.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:54 -04:00
Valentin Longchamp
b737337aaf net/phy: support the mv88e6352 switch
This patch add support for the configuration of an external switch from
the 88E6xxx series from Marvell trough an MDIO link using indirect
adressing. This can be used if we do not want to use an EEPROM for the
configuration.

This driver is not generic and was not tested on other switches than the
88e6352. This is proposed as a first implementation that is somewhat
limited but works and that can be used as a basis for further
developments for this switch family.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
2012-09-27 12:21:56 -05:00
Nobuhiro Iwamatsu
5751aa2f24 phy: Add support for SMSC LAN87xx PHYs
This adds support for the SMSC LAN87xx PHYs.

Following PHYs can be used by set CONFIG_PHY_SMSC to config.
 - SMSC LAN8700
 - SMSC LAN8710/LAN8720
 - SMSC LAN8710/LAN8720

A setup of PHY was copied from linux kenrel.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Fixed white space errors; modified commit message a bit.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-05 23:07:59 +01:00
Andy Fleming
9082eeac5d phylib: Add a bunch of PHY drivers from tsec
The tsec driver had a bunch of PHY drivers already written. This
converts them all into PHY Lib drivers, and serves as the first
set of PHY drivers for PHY Lib.

While doing that, cleaned up a number of magic numbers (though
not all of them, as PHY vendors like to keep their numbers as
magical as possible).  Also, noticed that almost all of the
vitesse/cicada PHYs had the same config/parse/startup functions,
so those have been collapsed into one.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:34 -05:00
Andy Fleming
5f184715ec Create PHY Lib for U-Boot
Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme.  The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support

The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).

The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.

We now have MDIO drivers and PHY drivers

An MDIO driver provides:
read
write
reset

A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed

The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()

Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)

We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.

We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,

we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.

Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:19 -05:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Prafulla Wadaskar
6f51deb7f2 Marvell MV88E61XX Switch Driver support
Chips supported:-
1. 88E6161 6 port gbe swtich with 5 integrated PHYs
2. 88E6165 6 port gbe swtich with 5 integrated PHYs
2. 88E6132 3 port gbe swtich with 2 integrated PHYs
Platform specific configuration supported for:-
default or router port vlan configuration
led_init configuration
mdip/n polarity reversal configuration

Note: This driver is supported and tested against
kirkwood egiga interface

Contributors:
Yotam Admon <yotam@marvell.com>
Michael Blostein <michaelbl@marvell.com

Reviewed by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:54 -07:00
Jean-Christophe PLAGNIOL-VILLARD
ba7b5b2348 miiphyutil: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29 21:53:56 +02:00
Jean-Christophe PLAGNIOL-VILLARD
55195773ea miiphybb: move to drivers/net/phy
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29 12:25:02 +02:00