Commit graph

14 commits

Author SHA1 Message Date
Kumar Gala
7e1afb62a7 ppc: Split MPC83xx SERDES code from MPC85xx/MPC86xx/QorIQ
The MPC83xx SERDES control is different from the other FSL PPC chips.
For now lets split it out so we can standardize on interfaces for
determining of a device on SERDES is configured.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
2010-04-26 22:37:57 -05:00
Anton Vorontsov
c9646ed758 mpc83xx: MPC837XERDB: Add support for FSL eSDHC
This patch adds support for eSDHC on MPC837XERDB boards. The WP
switch doesn't seem to work on RDB boards though, the WP pin is
always asserted (can see the pin state when it's in GPIO mode).

FSL DR USB and FSL eSDHC are mutually exclusive because of pins
multiplexing, so user should specify 'esdhc' or 'dr_usb' options
in the hwconfig environment variable to choose between the
devices.

p.s.
Now we're very close to a monitor len limit (196 bytes left using
gcc-4.2.0), so also increase the monitor len by one sector (64 KB).

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-16 22:25:34 +02:00
Peter Tyser
9adda5459c 83xx: Replace CONFIG_ECC_INIT_VIA_DDRC references
Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to
CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures
use

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-07-02 11:15:49 -05:00
Anton Vorontsov
55c531984d mpc83xx: fix serdes setup for the MPC8378E boards
MPC837xE specs says that SerDes1 has:

— Two lanes running x1 SGMII at 1.25 Gbps;
— Two lanes running x1 SATA at 1.5 or 3.0 Gbps.

And for SerDes2:

— Two lanes running x1 PCI Express at 2.5 Gbps;
— One lane running x2 PCI Express at 2.5 Gbps;
— Two lanes running x1 SATA at 1.5 or 3.0 Gbps.

The spec also explicitly states that PEX options are not valid for
the SD1.

Nevertheless MPC8378 RDB and MDS boards configure the SD1 for PEX,
which is wrong to do.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-10-21 18:33:25 -05:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Anton Vorontsov
d26154c9a6 mpc83xx: spd_sdram: fix ddr sdram base address assignment bug
The spd_dram code shifts the base address, then masks 20 bits, but
forgets to shift the base address back. Fix this by just masking the
base address correctly.

Found this bug while trying to relocate a DDR memory at the base != 0.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-09-24 09:58:33 -05:00
Becky Bruce
9973e3c614 Change initdram() return type to phys_size_t
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory.  phys_size_t is defined as an unsigned long on almost
all current platforms.

This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram).  It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.

Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-12 08:50:18 +02:00
Jean-Christophe PLAGNIOL-VILLARD
1ac4f320bf mpc837xerdb: Fix warning: implicit declaration of function 'fdt_fixup_dr_usb'
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-04-11 17:46:17 -05:00
Kim Phillips
e5c4ade4db mpc83xx: cleanup System Part and Revision ID Register (SPRIDR) code
in the spirit of commit 1ced121600,
85xx's "Update SVR numbers to expand support", simplify SPRIDR processing
and processor ID display.  Add REVID_{MAJ,MIN}OR macros to make
REVID dependent code simpler.  Also added PARTID_NO_E and IS_E_PROCESSOR
convenience macros.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-03-28 16:01:06 -05:00
Anton Vorontsov
18e69a35ef 83xx/fdt_support: let user specifiy FSL USB Dual-Role controller role
Linux understands "host" (default), "peripheral" and "otg" (broken).
Though, U-Boot doesn't restrict dr_mode variable to these values (think
of renames in future).

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-03-25 19:19:39 -05:00
Anton Vorontsov
2bd7460e92 83xx: initialize serdes for MPC837XRDB boards
On the MPC8377ERDB: 2 SATA and 2 PCI-E.
On the MPC8378ERDB: 2 PCI-E
On the MPC8379ERDB: 4 SATA

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-03-25 19:16:45 -05:00
Timur Tabi
89c7784ed9 83xx: Add Vitesse VSC7385 firmware uploading
Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware.  Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-03-25 19:16:43 -05:00
Jon Loeliger
a30a549a35 Remove erroneous or extra spd.h #includers.
Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
2008-03-05 00:17:43 +01:00
Kim Phillips
5e918a98c2 Add support for the MPC837xERDB
MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
*	       TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
*		       load)

Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16 12:32:39 -06:00