Commit graph

31 commits

Author SHA1 Message Date
Bastian Ruppert
de57550294 da850/omap-l138: davinci_emac: Suppress auto negotiation if needed
negotiation is enabled in RMII mode. Some boards based on da850 need
to suppress this procedure.

CC: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
CC: Lad, Prabhakar <prabhakar.lad@ti.com>
CC: Hadli, Manjunath <manjunath.hadli@ti.com>
CC: sbabic@denx.de
Acked-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <trini@ti.com>
Signed-off-by: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>
Acked-by: Prabhakar Lad <prabhakar.lad@ti.com>
2012-10-01 10:02:13 -07:00
Rajashekhara, Sudhakar
b78375a806 da850/omap-l138: Enable auto negotiation in RMII mode
On DA850/OMAP-L138 it was observed that in RMII mode,
auto negotiation was not performed. This patch enables
auto negotiation in RMII mode. Without this patch, EMAC
initialization takes more time and sometimes tftp fails
in RMII mode.

Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
2012-07-07 14:07:35 +02:00
Joe Hershberger
bbcdefb343 davinci: Fix Ethernet driver interface warning
Fixes:
davinci_emac.c: In function 'davinci_emac_initialize':
davinci_emac.c:796:12: warning: assignment from incompatible pointer type [enabled by default]

Tested on da850_am18xxevm

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
2012-05-22 10:18:14 -05:00
Prabhakar Lad
b609009801 ARM: davici_emac: Fix condition for number of phy detects
Fix the condition for number of phys in
davinci_eth_phy_detect() function.
CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT indicates number of
phys. From this commit id dc02badab4
davinci emac initilazed one less than the number of phy count.

Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
2011-12-06 23:59:37 +01:00
Ilya Yanok
80deda5d8e davinci_emac: hardcode 100Mbps for AM35xx and RMII
For some reason code setting the speed based on the PHY feedback causes
troubles on AM3517 so hardcode 100Mbps for now.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2011-12-06 23:59:35 +01:00
Ilya Yanok
2aa8720257 davinci_emac: fix for running with dcache enabled
DaVinci EMAC is present on TI AM35xx SoCs (ARMv7) which run with D-Cache
enabled by default. So we have to take care and flush/invalidate the
cache before/after the DMA operations.

Please note that the receive buffer alignment to 32 byte boundary comes
from the old driver version I don't know if it is really needed or
alignment to cache line size is enough.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2011-12-06 23:59:35 +01:00
Ilya Yanok
918588cfd3 davinci_emac: conditionally compile specific PHY support
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2011-12-06 23:59:35 +01:00
Ilya Yanok
82b772178d davinci_emac: use internal addresses in buffer descriptors
On AM35xx CPPI RAM had different addresses when accessed from the CPU
and from the EMAC. We need to account this to deal with the buffer
descriptors correctly.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2011-12-06 23:59:35 +01:00
Ilya Yanok
7c587d320d davinci_emac: move arch-independent defines to separate header
DaVinci EMAC is found not only on DaVinci SoCs but on some OMAP3 SoCs
also. This patch moves common defines from arch-davinci/emac_defs.h to
drivers/net/davinci_emac.h

DaVinci specific PHY drivers hacked to include the new header. We might
want to switch to phylib in future.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2011-12-06 23:59:35 +01:00
Heiko Schocher
dc02badab4 arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
since commits:
davinci: emac: add support for more than 1 PHYs
062fe7d332

davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
fb1d6332b5

I get following warning on the enbw_cmc board:

Err:   serial
Net:    5 ETH PHY detected
miiphy_register: non unique device name 'KSZ8873 @ 0x01'
DaVinci-EMAC
Hit any key to stop autoboot:  0

Also I see some debug printfs:

=> run load
+ emac_close
+ emac_ch_teardown
- emac_ch_teardown
+ emac_ch_teardown
- emac_ch_teardown
- emac_close
+ emac_open
- emac_open
Using DaVinci-EMAC device

reason is 062fe7d332 new define MAX_PHY.
This is set to 3! I get on this board 5 active phys, so
this leads in wrong memory writes ...

so I changed:

- define CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT to set
  the MAX_PHY value, add a description in README
  for the new CONFIG_SYS option.
- print an error message if more then MAX_PHYs are
  detected.
- fill the active_phy_addr array in a for loop with
  0xff
- changed printf() in debug_emac()

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Tom Rini <tom.rini@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:51 +01:00
Heiko Schocher
882ecfa390 net, davinci_emac: make clock divider in MDIO control register configurable
Define CONFIG_SYS_EMAC_TI_CLKDIV for setting the clkdiv value
in the MDIO control register.

Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Sandeep Paulraj <s-paulraj@ti.com>
cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:24 +01:00
Ilya Yanok
e0297a5599 davinci_emac: compilation fix, phy is array now
Fix compilation issues introduced by recent multiply PHY patch.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-03 22:56:23 +01:00
Manjunath Hadli
fb1d6332b5 davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
remove macro CONFIG_EMAC_MDIO_PHY_NUM and depending macro EMAC_MDIO_PHY_NUM
as they are no longer needed with the support for more than 1 PHYs in davinci
emac driver.

Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:36 +02:00
Manjunath Hadli
062fe7d332 davinci: emac: add support for more than 1 PHYs
add support for more than 1 PHYs. Many of the davinci platforms have more
than 1 PHYs on thier board. This patch extends support in davinci emac
driver for upto 3 PHYs.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:36 +02:00
Manjunath Hadli
cc4bd47f4f davinci: emac: add new features to autonegotiate for EMAC
add more features like DUPLEX, 100MB link speed etc to auto negotiate
in EMAC driver. EMAC controller autonegotiates for these features with
PHYs which are on the board.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:36 +02:00
Heiko Schocher
19fdf9a1c3 net, davinci_emac: let the EMAC detect the PHYs
Once the MDIO state machine has been initialized and enabled, it
starts polling all 32 PHY addresses on the MDIO bus, looking for
an active PHY. Add a 5 ms delay, so all PHYs are for sure detected.

This problem was detected on the cmc board with a KSZ8864 switch.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:57 +02:00
Heiko Schocher
c3b4a475d7 net, davinci_emac: make less verbose - turn printf() into debug()
The PHY driver was too verbose and corrupted the boot message display
like this:

...
Net:   Ethernet PHY: KSZ8873 @ 0x02
DaVinci-EMAC
...

Turn printf() into debug() so we get the expected output again:

...
Net:   DaVinci-EMAC
...

Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Paulraj Sandeep <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:56 +02:00
Heiko Schocher
4f3c42aca4 net, davinci_emac: add KSZ8864 switch
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:56 +02:00
Nagabhushana Netagunte
ba511f779a da850: fix the channel number for EMAC teardown init
TX and RX channel numbers programmed as '1' during EMAC
teardown initialization is wrong. This patch fixes the
same by setting channel number to '0' which is used by U-boot.

Signed-off-by: Sugumar Natarajan <sugumar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04 11:36:19 +02:00
Ben Gardiner
7d2fade7b1 ea20: fix undefined PHY_* errors
This patch fixes ea20 after 8ef583a035 where
the u-boot custom PHY_ macros were replaced with those of linux/mii.h MII_
definitions except in the RMII support for davinci_emac. Probably also due to
the merge path of changes in 2010.12.

Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca>
CC: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-04-11 21:28:44 +02:00
Sandeep Paulraj
840f8923a0 DaVinci DM6467: Added ET1011C (LSI) PHY support
Added arch/arm/cpu/arm926ejs/davinci/et1011c.c for handling
ET1011C gigabit phy. which overrides get_link_speed function
from default implementation. This enables output of 125 MHz
reference clock on SYS_CLK pin.

Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-02-02 00:54:44 +01:00
Sandeep Paulraj
2a7d603f37 DaVinci EMAC: Add name to Ethernet device
Adds "DaVinci-EMAC" as the name of the device so that
it gets printed as "Using DaVinci-EMAC device"
during network access (dhcp, tftp) instead of empty name
in "Using" statement.This name also gets
reflected in 'ethact' env variable.


Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-02-02 00:54:44 +01:00
Sandeep Paulraj
4b9b9e7c66 DaVinci EMAC: Fix davinci_eth_gigabit_enable
Enabling the gigabit was overwriting the
previous configuration by setting up only GIGAFORCE and
GIG bits of MAC control register.
Modified to retain previous configuration while
gigabit enabling.

Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-02-02 00:54:44 +01:00
Mike Frysinger
8ef583a035 miiphy: convert to linux/mii.h
The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-01-09 18:06:50 +01:00
Sudhakar Rajashekhara
d26074012b da850: Add RMII support for EMAC
This patch is a port of the work by Sudhakar Rajeshekhara in commit
ab3effbcad8851cc65dc5241a01c064d2030a3b2 of
git://arago-project.org/git/people/sandeep/u-boot-davinci.git.

The da850 UI board has on it an RMII PHY which can be used if the MDC line
to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by
configuring the values of some GPIO pins on the IO expander of the UI board.
This patch implements disabling that line via GPIO2[6], configuring the UI
board's IO expander and setting only the pinmux settings that are needed for
RMII operation.

Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-30 11:27:44 -05:00
Ben Gardiner
7b37a27e14 davinci_emac: davinci_eth_set_mac_addr to ->write_hwaddr
This patch proposes to migrate the davinci_emac driver to using the
eth_device->write_hwaddr function pointer as suggested by Ben Warren.

All the davinci boards had the behaviour, prior to this patch, of
sync'ing the environment variable enetaddr with the MAC address read
from non-volatile storage on boot -- when the two locations disagreed,
the environment variable value took precendence. This patch keeps the
same behaviour but lets eth_initialize take care of it.

This patch refactors davinci_emac setup in the boards so that the MAC
address is read from non-volatile storage into the environment variable
and then the environment variable value is use in eth_intialize. The
only exception is the direct call to davinci_eth_set_mac_addr made by
the da830evm board init which was changed into an assignment of the
enetaddr field.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11 23:07:17 -07:00
Mike Frysinger
5700bb6352 miiphy: constify device name
The driver name does not need to be writable, so constify it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-08-09 11:52:29 -07:00
Nick Thompson
d7e354374c TI: DaVinci: Updating EMAC driver for DM365, DM646x and DA8XX
The EMAC IP on DM365, DM646x and DA830 is slightly different
from that on DM644x. This change updates the DaVinci EMAC driver
so that EMAC becomes operational on SOCs with EMAC v2.

Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:37:12 -08:00
Ben Warren
8453587ef9 Switched davinci_emac Ethernet driver to use newer API
Added CONFIG_NET_MULTI to all Davinci boards
Removed all calls to Davinci network driver from board code
Added cpu_eth_init() to cpu/arm926ejs/cpu.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:54 -07:00
Ben Warren
8cc13c13f1 Initial cleanup of Davinci Ethernet driver
Removed pointless #ifdefs
 Moved functions around in file in preparation for switch to newer API

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:54 -07:00
Ben Warren
09cdd1b9b0 Moved Davinci Ethernet driver to drivers/net
This driver has been renamed davinci_emac.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:54 -07:00
Renamed from cpu/arm926ejs/davinci/ether.c (Browse further)