A number of config files define the V_PROMPT macro for the
command-line prompt, only to immediately use that macro to define
CONFIG_SYS_PROMPT, making V_PROMPT entirely superfluous.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Not all boards have both LEDs hooked, so enabling both on
boards with single LED will just waste power. Make it
possible to choose LEDs by adding argument to
twl4030_led_init().
Using this turn on only LEDB for pandora, leave both LEDs
on for all other boards, as it was before this patch.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
The latest changes increased the size of the alpr image a bit more.
Now it doesn't fit into the 256k reserved for it. This patch now removes
the commands "ping" and "diag" which are not needed in the production
systems.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl>
Prototype for gunzip/zunzip was only in lib_generic/gunzip.c and thus
repeated in every file using it. This patch moves the prototypes to
common.h and removes all prototypes distributed anywhere else.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
The preferred serial output comes from the debug board.
When the debug board is disconnected, fall back on using
usbtty from the usb connector on the Zoom2 board.
This shows up as /dev/ttyACM0 in a linux host.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Zoom2 needs to use these declarations and the include directory is a
better place from them than in the middle of the driver directory.
It did not make sense to create a new file for just a couple of
lines so they were appended to the serial.h
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The primary console of beagle is the serial header.
A secondary console is to use the usbtty. The user can set this
manually by doing
setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty
saveenv
usbtty will be usable by accessing the /dev/ttyACM0 on a linux host.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The primary console of zoom1 is the serial out from the jumpers
accessed by removing the back panel.
A secondary console is to use the usbtty. The user can set this
manually by doing
setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty
saveenv
usbtty will be usable by accessing the /dev/ttyACM0 on a linux host.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This change adds the usb device support for musb.
Omap3 platform support added at the same level as davinci.
The interface for usbtty to use the musb device support was added.
Verified on omap3 beagle, zoom1 and zoom2.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The twl4030 provides a PHY device for connecting a link device,
like musb, to physical connection.
This change adds the twl4030 usb registers and functions for
initializing the PHY as required by omap3.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The header files usb.h and usbdescriptors.h have the same nameed
structure definitions for
usb_config_descriptor
usb_interface_descriptor
usb_endpoint_descriptor
usb_device_descriptor
usb_string_descriptor
These are out right duplicates in usb.h
usb_device_descriptor
usb_string_descriptor
This one has extra unused elements
usb_endpoint_descriptor
unsigned char bRefresh
unsigned char bSynchAddress;
These in usb.h have extra elements at the end of the usb 2.0
specified descriptor and are used.
usb_config_descriptor
usb_interface_descriptor
The change is to consolidate the definition of the descriptors
to usbdescriptors.h. The dublicates in usb.h are removed.
The extra element structure will have their name shorted by
removing the '_descriptor' suffix.
So
usb_config_descriptor -> usb_config
usb_interface_descriptor -> usb_interface
For these, the common descriptor elements are accessed now
by an element 'desc'.
As an example
- if (iface->bInterfaceClass != USB_CLASS_HUB)
+ if (iface->desc.bInterfaceClass != USB_CLASS_HUB)
This has been compile tested on MAKEALL arm, ppc and mips.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
A previous Commit converted the LAN91C96 Ethernet driver to using the
CONFIG_NET_MULTI API, but did not include full board support. This patch
finishes the job.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Neither the MVBLUE nor its underlying architecture implement the
do_irqinfo() function which is required when CONFIG_CMD_IRQ is defined.
This change fixes the following MVBLUE compiler error:
-> ./MAKEALL MVBLUE
Configuring for MVBLUE board...
common/libcommon.a(cmd_irq.o):(.u_boot_cmd+0x24): undefined reference to `do_irqinfo'
make: *** [u-boot] Error 1
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
The support for this was silently dropped by a configuration
split during the merge of the imx27lite board support in commit
864aa034f3 (cmd_mtdparts: Move to common
handling of FLASH devices via MTD layer).
Signed-off-by: Detlev Zundel <dzu@denx.de>
This chip is equipped for example on the esd PMC-ETH2-GB board. So let's
add it to the list of supported chips to the e1000 driver.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This modification is NOT tested on any of the
platforms modified as I dont have them. please
help by testing+building+fixing
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Enable the NET MULTI option and remove build warning
Tested: SDP3430
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Make the lan91c96 driver capable of CONFIG_NET_MULTI
to be clean for the new arch, add a a lil detect function
Most of the formatting change was done to keep checkpatch
silent, but a few functions and #if 0ed code which
does not make sense for NET_MULTI have been removed
Now, use the lan91c96_initialize() function to init the driver
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.
Signed-off-by: Heiko Schocher <hs@denx.de>
We are using generic implementation of ffs. This should
be part of Simon's commit 0413cfecea
Here is warning message which this patch removes.
In file included from /tmp/u-boot-microblaze/include/common.h:38,
from cmd_mtdparts.c:87:
/tmp/u-boot-microblaze/include/linux/bitops.h:123:1: warning: "ffs" redefined
In file included from /tmp/u-boot-microblaze/include/linux/bitops.h:110,
from /tmp/u-boot-microblaze/include/common.h:38,
from cmd_mtdparts.c:87:
/tmp/u-boot-microblaze/include/asm/bitops.h:269:1:
warning: this is the location of the previous definition
Signed-off-by: Michal Simek <monstr@monstr.eu>
A typo caused the stack and malloc regions to overlap, which prevented
mem_malloc_init() from returning. This commit makes the memory layout match
the example described in include/configs/microblaze-generic.h
Signed-off-by: Graeme Smecher <graeme.smecher@mail.mcgill.ca>
Signed-off-by: Michal Simek <monstr@monstr.eu>
add the following commands for the manroland boards:
CONFIG_CMDLINE_EDITING
CONFIG_COMMAND_HISTORY
CONFIG_AUTO_COMPLETE
Signed-off-by: Heiko Schocher <hs@denx.de>
Add lzop decompression support to the existing lzo bitstream handling
(think gzip versus zlib), and support it for uImage decompression if
CONFIG_LZO is enabled.
Lzop doesn't compress as good as gzip (~10% worse), but decompression
is very fast (~0.7s faster here on a slow ppc). The lzop decompression
code is based on Albin Tonnerre's recent ARM Linux lzo support patch.
Cc: albin.tonnerre@free-electrons.com
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
According to the PPC reference implementation the udelay() function is
responsible for resetting the watchdog timer as frequently as needed.
Most other architectures do not meet that requirement, so long-running
operations might result in a watchdog reset.
This patch adds a generic udelay() function which takes care of
resetting the watchdog before calling an architecture-specific
__udelay().
Signed-off-by: Ingo van Lil <inguin@gmx.de>
We will get compilation warnings without
"CONFIG_SYS_64BIT_VSPRINTF" being defined
in the board config.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for A320 evaluation board from Faraday. This board
uses FA526 processor by default and has 512kB and 32MB NOR flash, 64M RAM.
FA526 is an ARMv4 processor and uses the ARM920T source in this patch.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Defaults are for Infineon DDR timings.
Since none of the supported boards currently do
XIP boot, these seem to be faulty. fix the values
as per the calculations(ACTIMA,B), conf
the sdrc power with pwdnen and wakeupproc bits
Signed-off-by: Nishanth Menon <nm@ti.com>
Integrate DA830 EVM support into U-Boot.
Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum
Digital EVM board. See http://www.spectrumdigital.com/
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
Provides initial support for TI OMAP-L1x/DA8xx SoC devices.
See http://www.ti.com
The DA8xx devices are similar to DaVinci devices but have a differing
memory map and updated peripheral versions.
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Fix stack_setup to place the stack on the correct address in DRAM
accroding to U-Boot standard and remove conditional compilation by
CONFIG_MEMORY_UPPER_CODE macro that is not necessry. This macro
was introduced and used only by this board for some unclear reason.
The definition of this macro is also removed because it's not
referenced elsewhere.
Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com>
Tested-by: Minkyu Kang <mk7.kang@samsung.com>
Cleans up the s3c24x0 header files:
s4c24x0.h: removes the use of 'volatile' from the S3C24X0_REG8,
S3C24X0_REG16 and S3C24X0_REG32 register typedef's. Registers are always
accessed using the IO accessor functions which cast the register address
as 'volatile' anyway so it isn't required here.
s3c2400.h and s3c2410.h: insert a blank line between the static inline
functions
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
This patch moves the s3c24x0 header files from include/ to
include/asm-arm/arch-s3c24x0/.
checkpatch.pl showed 2 errors and 3 warnings. The 2 errors were both due
to a non-UTF8 character in David M?ller's name:
ERROR: Invalid UTF-8, patch and commit message should be encoded in UTF-8
#489: FILE: include/asm-arm/arch-s3c24x0/s3c2410.h:3:
+ * David M?ller ELSOFT AG Switzerland. d.mueller@elsoft.ch
As David's name correctly contains a non-UTF8 character I haven't fixed
these errors.
The 3 warnings were all because of the use of 'volatile' in s3c24x0.h:
WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt
#673: FILE: include/asm-arm/arch-s3c24x0/s3c24x0.h:35:
+typedef volatile u8 S3C24X0_REG8;
+typedef volatile u16 S3C24X0_REG16;
+typedef volatile u32 S3C24X0_REG32;
I'll fix these errors in another patch.
Tested by running MAKEALL for ARM8 targets and ensuring there were no new
errors or warnings.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The autoupdate feature is not used on PLU405 boards.
So remove it.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch cleans up the PPC4xx I2C intrastructure:
- Use C struct to describe the I2C registers instead of defines
- Coding style cleanup (braces, whitespace, comments, line length)
- Extract common code from i2c_read() and i2c_write()
- Remove unneeded IIC defines from ppc405.h & ppc440.h
Signed-off-by: Stefan Roese <sr@denx.de>
This patch shrinks the PMC440 u-boot binary (from next branch)
to fit into 384kB again.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
The latest changes in the u-boot/next branch increased the size of the
alpr image a bit more. Now it doesn't fit into the 256k reserved for it.
This patch now removes the commands "askenv" and "irq" which are not
needed in the production systems.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl>
This patch removes the duplicted implementations of the pci_master_init()
function by introducing a weak default function for it. It can be
overridden by a board specific version.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the duplicted implementations of the pci_pre_init()
function by introducing a weak default function for it. This weak default
has a different implementation for some PPC variants. It can be
overridden by a board specific version.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the duplicted implementations of the pci_target_init()
function by introducing a weak default function for it. This weak default
has a different implementation for 440EP(x)/GR(x) PPC's. It can be
overridden by a board specific version (e.g. PMC440, korat).
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
NANDs with page size of lesser than and equal to 2K are
reaching EOL. They are bing replaced with NANDs of
page size 4K and above.
To support this we have to extend the eccpos field
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch fixes an ugly behavior of the IL712 magnetic couplers
as used on PLU405. These parts will remember their last state
over a power cycle which might cause unwanted behavior.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is in preparation for the upcoming PLU405 board fix.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support to use second and third I2C bus, too.
Bus 0 is still the default, but by calling i2c_set_bus_num(1/2) before doing
I2C accesses, code can switch to bus 1 and 2, too. Don't forget to switch
back afterwards, then.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Define and use CONFIG_ENV_ADDR_FLEX and CONFIG_ENV_SIZE_FLEX
for storing environment variables.
Signed-off-by: Rohit Hagargundgi <h.rohit@samsung.com>
Signed-off-by: Amul Kumar Saha <amul.saha@samsung.com>
This patch adds support for Flex-OneNAND devices.
Signed-off-by: Rohit Hagargundgi <h.rohit@samsung.com>
Signed-off-by: Amul Kumar Saha <amul.saha@samsung.com>
This patch adds support for NANDs greater than 2 GB.
Patch is based on the MTD NAND driver in the kernel.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Both lpd7a400 and lpd7a404 failed to compile because they had
CONFIG_SMC_USE_IOFUNCS defined:
examples/standalone/smc91111_eeprom.c:388: undefined reference to `SMC_outw'
Also removed an orphaned paren in lpd7a404.h
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch fixes a problem only seen very occasionally on Canyonlands.
The NOR flash interface (CFI driver) doesn't work reliably in all cases.
Erasing and/or programming sometimes doesn't work. Sometimes with
an error message, like "flash not erased" when trying to program an
area that should have just been erased. And sometimes without any error
messages. As mentioned above, this problem was only seen rarely and with
some PLL configuration (CPU speed, EBC speed).
Now I spotted this problem a few times, when running my Canyonlands with
the following setup (chip_config):
1000-nor - NOR CPU:1000 PLB: 200 OPB: 100 EBC: 100
Changing the EBC configuration to not release the bus into high
impedance state inbetween the transfers (ATC, DTC and CTC bits set to 1
in EBC0_CFG) seems to fix this problem. I haven't seen any failure
anymore with this patch applied.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: David Mitchell <dmitchell@amcc.com>
Cc: Jeff Mann <MannJ@embeddedplanet.com>
This patch consolidates the PPC4xx board specific PCIe configuration
code. This way the duplicated code is removed. Boards can implement a
special, non standard behaviour (e.g. number of PCIe slots, etc) by
overriding the weak default functions.
Signed-off-by: Stefan Roese <sr@denx.de>
The asm-arm/unaligned.h includes linux/unaligned/access_ok.h
This file is unsafe to be used on ARM, since it does an unaligned memory
accesses which fails on ARM.
Lookin at Linux the basic difference seems to be the header
"include/asm-arm/unaligned.h". The Linux version of "unaligned.h"
does *not* include "access_ok.h" at all. It includes "le_byteshift.h"
and "be_byteshift.h" instead.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Stefan Roese <sr@denx.de>
--
include/asm-arm/unaligned.h | 3 -
include/linux/unaligned/be_byteshift.h | 70 +++++++++++++++++++++++++++++++++
include/linux/unaligned/le_byteshift.h | 70 +++++++++++++++++++++++++++++++++
3 files changed, 142 insertions(+), 1 deletion(-)
create mode 100644 include/linux/unaligned/be_byteshift.h
create mode 100644 include/linux/unaligned/le_byteshift.h
commit 70ed869e broke fsl pcie end-point initialization.
Returning 0 is not correct. The function must return the first free
bus number for the next controller.
fsl_pci_init() must still be called and a bus allocated even if the
controller is an end-point.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 70ed869ea5.
There isn't any need to modify the API for fsl_pci_init_port to pass the
status of host/agent(end-point) status. We can determine that
internally to fsl_pci_init_port. Revert the patch that makes the API
change.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the board IPEK01 based on the MPC5200.
The Futjitsu Lime graphics controller is configured in 16 bpp mode.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
In 16 bpp mode, the new IPEK01 board only requires swapping of D16 words
for D32 accesses due to the diffferent connecting to the GDC bus. This
patch introduces the configuration option VIDEO_FB_16BPP_WORD_SWAP,
which should be set for all board using the mb862xx in 16 bpp mode. For
the IPEK01, VIDEO_FB_16BPP_PIXEL_SWAP should not be set.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
The new IPEK01 board can use the 32 bpp mode for the Lime graphics
controller. For this mode, video accelaration does not work. This patch
makes the accelaration configurable via CONFIG_VIDEO_MB862xx_ACCEL,
which is enabled for the lwmon5 and the socrates board for backward
compatibility.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
To avoid board-specific code accessing the mb862xx registers directly,
the public function mb862xx_probe() has been introduced. Furthermore,
the "Change of Clock Frequency" and "Set Memory I/F Mode" registers
are now defined by CONFIG_SYS_MB862xx_CCF and CONFIG_SYS_MB862xx__MMR,
respectively. The BSPs for the socrates and lwmon5 boards have been
adapted accordingly.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
The comment for the BR0_PRELIM port size initialization incorrectly
stated 32 bit, while it's actually 16 bit. The code is correct.
Reported-by: Guenter Koellner <guenter.koellner@nsn.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Extend bootdelay to 10 seconds. Set boot retry time to 120 seconds and use
reset to retry. Define default bootcommand and bootargs for production.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Currently the CFI driver issues both AMD and Intel reset commands.
This is because the driver doesn't know yet which chips are connected.
This dual reset seems to cause problems with the M29W128G chips as
reported by Richard Retanubun. This patch now introduces a weak default
function for the CFI reset command, still with both resets. This can
be overridden by a board specific version if necessary.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Richard Retanubun <RichardRetanubun@ruggedcom.com>
The editenv command can be used to edit an environment variable.
Editing an environment variable is useful when one wants to tweak an
existing variable, for example fix a typo or change the baudrate in the
'bootargs' environment variable.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Simply add some defines, and adjust TLBe setup to include some
space for eLBC NAND.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
eSDHC is mutually exlusive with UART0 (in 4-bits mode) and I2C2
(in 1-bit mode). When eSDHC is used, we should switch u-boot console to
UART1, and make the proper device-tree fixups.
Because of an erratum in prototype boards it is impossible to use eSDHC
without disabling UART0 (which makes it quite easy to 'brick' the board
by simply issung 'setenv hwconfig esdhc', and not able to interact with
U-Boot anylonger).
So, but default we assume that the board is a prototype, which is a most
safe assumption. There is no way to determine board revision from a
register, so we use hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This change has 3 goals:
- Have secondary cores be released into spin loops at their 'true'
address in SDRAM. Previously, secondary cores were put into spin
loops in the 0xfffffxxx address range which required that boot page
translation was always enabled while cores were in their spin loops.
- Allow the TLB window that the primary core uses to access the
secondary cores boot page to be placed at any address. Previously, a
TLB window at 0xfffff000 was always used to access the seconary cores'
boot page. This TLB address requirement overlapped with other
peripherals on some boards (eg XPedite5370). By default, the boot
page TLB will still use the 0xfffffxxx address range, but this can be
overridden on a board-by-board basis by defining a custom
CONFIG_BPTR_VIRT_ADDR. Note that the TLB used to map the boot page
remains in use while U-Boot executes. Previously it was only
temporarily used, then restored to its initial value.
- Allow Boot Page Translation to be disabled on bootup. Previously,
Boot Page Translation was always left enabled after secondary cores
were brought out of reset. This caused the 0xfffffxxx address range
to somewhat "magically" be translated to an address in SDRAM. Some
boards may not want this oddity in their memory map, so defining
CONFIG_MPC8xxx_DISABLE_BPTR will turn off Boot Page Translation after
the secondary cores are initialized.
These changes are only applicable to 85xx boards with CONFIG_MP defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Originally written by Jason Jin and Mingkai Hu for mpc8536.
When QorIQ based board is configured as a PCIe agent, then unlock/enable
inbound PCI configuration cycles and init a 4K inbound memory window;
so that a PCIe host can access the PCIe agents SDRAM at address 0x0
* Supported in fsl_pci_init_port() after adding pcie_ep as a param
* Revamped copyright in drivers/pci/fsl_pci_init.c
* Mods in 85xx based board specific pci init after this change
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fix the following compile warnings
warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Start of support of
Texas Instruments Software Development Platform(SDP)
for OMAP3430 - SDP3430
Highlights of this platform are:
Flash Memory devices:
Sibley NOR, Micron 8bit NAND and OneNAND
Connectivity:
3 UARTs and expanded 4 UART ports + IrDA
Ethernet, USB
Other peripherals:
TWL5030 PMIC+Audio+Keypad
VGA display
Expansion ports:
Memory devices plugin boards (PISMO)
Connectivity board for GPS,WLAN etc.
Completely configurable boot sequence and device mapping
etc.
Support default jumpering and:
- UART1/ttyS0 console(legacy sdp3430 u-boot)
- UART3/ttyS2 console (matching other boards,
and SDP HW docs)
- Ethernet
- mmc0
- NOR boot
Currently the UART1 is enabled by default. for
compatibility with other OMAP3 u-boot platforms,
enable the #define of CONSOLE_J9.
Conflicts:
Makefile
Fixed the conflict with smdkc100_config by moving omap_sdp3430_config
to it is alphabetically sorted location above zoom1.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Due to new TI boards being added to U-Boot, the hardware.h
is getting very messy. The warning being fixed is due to
the EMIF addresses being redefined.
The long term solution(after 2009.11) to this is to
have SOC specific header files.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
gpmc_config should not be a variant as it is board specific
hence make it a const parameter
Fixes issues identified by Dirk:
- build issue for zoom2
- warnings for all other OMAP3 platforms using nand/onenand etc
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch removes the Sequoia "bootstrap" command and replaces it
with the now common command "chip_config".
Please note that the patches with the dynamic PCI sync clock
configuration have to be applied, before this one should go in.
This is because Sequoia has 2 different bootstrap EEPROMs, and
the old bootstrap command configured different values depending
on the detected PCI async clock (33 vs. 66MHz). With the PCI sync
clock patches, this is not necessary anymore. The PCI sync clock
will be configured correctly on-the-fly now.
Signed-off-by: Stefan Roese <sr@denx.de>
PPC440EP(x)/PPC440GR(x):
In asynchronous PCI mode, the synchronous PCI clock must meet
certain requirements. The following equation describes the
relationship that must be maintained between the asynchronous PCI
clock and synchronous PCI clock. Select an appropriate PCI:PLB
ratio to maintain the relationship:
AsyncPCIClk - 1MHz <= SyncPCIclock <= (2 * AsyncPCIClk) - 1MHz
This patch now adds a function to check and reconfigure the sync
PCI clock to meet this requirement. This is in preparation for
some AMCC boards (Sequoia/Rainier and Yosemite/Yellowstone) using this
function to not violate the PCI clocking rules.
Signed-off-by: Stefan Roese <sr@denx.de>
Till now only the ranges in the ebc node are updated with the values
currently configured in the PPC4xx EBC controller. With this patch now
the NOR flash size is updated in the device tree blob as well. This is
done by scanning the compatible nodes "cfi-flash" and "jedec-flash"
for the correct chip select number.
This size fixup is enabled for all AMCC eval board right now. Other
4xx boards may want to enable it as well, if this problem with multiple
NOR FLASH sizes exists.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
This function can be used to update the size in the "reg" property
of the NOR FLASH device nodes. This is necessary for boards with
non-fixed NOR FLASH sizes.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Export enable_gpmc_cs_config into common header to
prevent warning:
warning: implicit declaration of function 'enable_gpmc_cs_config'
Signed-off-by: Nishanth Menon <nm@ti.com>
Adding the CONFIG_SYS_64BIT_VSPRINTF fot the DM644x based Sonata
Without this option enabled while performing NAND operations we will get
wrong diagnostic messages.
Example if the MTD NAND driver find a bad block while erasing from
a certain address, it will say bad block skipped at 0x00000000.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Adding the CONFIG_SYS_64BIT_VSPRINTF in the DVEVM config.
Without this option enabled while performing NAND operations we will get
wrong diagnostic messages.
Example if the MTD NAND driver find a bad block while erasing from
a certain address, it will say bad block skipped at 0x00000000.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Adding the CONFIG_SYS_64BIT_VSPRINTF in the DM365 EVM config.
Without this option enabled while performing NAND operations we will get
wrong diagnostic messages.
Example if the MTD NAND driver find a bad block while erasing from
a certain address, it will say bad block skipped at 0x00000000.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Adding the CONFIG_SYS_64BIT_VSPRINTF in the DM355 EVM config.
Without this option enabled while performing NAND operations we will get
wrong diagnostic messages.
Example if the MTD NAND driver find a bad block while erasing from
a certain address, it will say bad block skipped at 0x00000000.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Update default environment to support new kernel DSS2 subsystem and
simplify rootfs type and location changes.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
This patch adds the initial support for DM6467 EVM.
Other features like NET and NAND support will be added as follow up patches.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This change fixes the compiler warning
main.c: In function 'abortboot':
main.c:122: warning: too few arguments for format
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This change fixes the compiler warning
nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF
for correct output!
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The env code is protected by the ENV_IS_EMBEDDED define, so attempting to
compile the code when this isn't defined is pointless. Now that the env
headers have unified around CONFIG_ENV_IS_EMBEDDED, convert the build
system to only build the env objects when this is enabled. And now that
the env code is conditionally compiled, we can drop the source code checks.
For people who want to extract the environment manually, add a new option
CONFIG_BUILD_ENVCRC that only enables the envcrc utility.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is an orphaned legacy leftover that is just polluting
the config file namespace.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On Chip BootROM support for P1 and P2 series RDB platforms.
This patch is derived from latest On Chip BootROM support on MPC8536DS
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
NAND Boot support for P1 and P2 series RDB platforms.
This patch is derived from NAND Boot support on MPC8536DS.
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch re-formats the arm920t s3c24x0 header files in preparation for
changes to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patch 1/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This sets CONFIG_SYS_HZ to 1000 for all boards that use the s3c2400 and
s3c2410 cpu's which fixes various problems such as the timeouts in tftp being
too short.
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't
have any s3c2400 or s3c2410 boards but need this patch applying before I can
submit patches for the SBC2440-II Board. Also, ran MAKEALL for all ARM9 targets
and no new warnings or errors were found.
It was originally submitted on 21/06/2009 but didn't get into the 2009.08
release, and Jean-Pierre made one comment on the original patch (see
http://lists.denx.de/pipermail/u-boot/2009-July/055470.html). I've made two
changes to the original patch:
- it's been re-based to the current release
- I've re-named get_timer_raw() to get_ticks() in response to Jean-Pierre's comment
This affects the sbc2410, smdk2400, smdk2410 and trab boards. I've copied it
directly to the maintainers of all except the sbc2410 which doesn't have an
entry in MAINTAINERS.
Signed-off-by: Kevin Morfitt <kmorfitt@aselaptop-1.localdomain>
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds new board SMDKC100 that uses s5pc100 SoC
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
This patch includes the serial driver for s5pc1xx.
s5pc1xx uart driver needs own register setting and clock configuration.
So, need to special driver.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch includes the onenand driver for s5pc100
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch adds support for the Samsung s5pc100 and s5pc110
SoCs. The s5pc1xx SoC is an ARM Cortex A8 processor.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
This patch implements several updates:
-disable CONFIG_ENV_OVERWRITE
-add new hardware style variants and set the arch numbers appropriate
-pass the serial# and hardware revision to the kernel
-removed unused macros from include/configs/meesc.h
-fixed multiline comment style
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.
This also refactors the smc911x driver to allow for detecting when the
chip is missing. I.e. the detect_chip() function is called earlier and
will abort gracefully when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This changes fixes an early i2c error.
It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls i2c_init
inside its error handling check.
While it is ok to attempt error handling this way, the boards
must not depend on this side effect to initialize it's i2c.
Instead of explicitly calling i2c_init for every board, use
the generic arm initialization in lib_arm/board.c. By defining
the config variable CONFIG_HARD_I2C, the omap3 i2c initialization
is included in the init_sequence table.
Run tested on Beagle.
Compile tested on the omap3's
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Some DaVinci SOC's use GPIOs to enable EMAC and DM9000.
This patch adds some definitions for GPIO registers and also adds
structures for GPIO.
A separate header file is being added so that in future we
can have a DaVinci GPIO driver similer to OMAP.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
In the DaVinci specific code, we use both CONFIG_SOC_DM646X and
CONFIG_SOC_DM646x to represent DM646x specific code.
This patch changes occurrences of CONFIG_SOC_DM646x to
CONFIG_SOC_DM646X. This is because for DM644x series of SOCs we use
the flag CONFIG_SOC_DM644X. We want some uniformity.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
Robert P. J. Day
Grazvydas Ignotas
Wolfgang Denk
Stefan Roese
Wolfgang Wegner
Ajay Kumar Gupta
Tom Rix
Ben Warren
Peter Tyser
Detlev Zundel
Reinhard Arlt
Nishanth Menon
Heiko Schocher
Michal Simek
Graeme Smecher
Peter Korsgaard
Ingo van Lil
Graeme Russ
Becky Bruce
Sandeep Paulraj
Po-Yu Chuang
Sekhar Nori
Nick Thompson
kevin.morfitt@fearnside-systems.co.uk
Seunghyeon Rhee
Minkyu Kang
Matthias Fuchs
Mike Frysinger
Remy Bohmer
Mark Jackson
Matthias Fuchs
Dirk Behme
Amul Kumar Saha
Ed Swarthout
Kumar Gala
Wolfgang Grandegger
Anatolij Gustschin
Valentin Yakovenkov
Eric Millbrandt
Anton Vorontsov
Vivek Mahajan
Steve Sakoman
Eric Benard
Martha Stan
Paul Gortmaker
Dipen Dudhat
Daniel Gorsulowski
Olof Johansson