We are getting very close to running out of space in SPL, and with the
currently Chrome OS gcc 4.9 we exceed the limit. Add a litle more space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
As best I can tell, CONFIG_SYS_LOAD_ADDR and CONFIG_LOADADDR/$loadaddr
serve essentially the same purpose. Roughly, if a command takes a load
address, then CONFIG_SYS_LOAD_ADDR or $loadaddr (or both) are the default
if the command-line does not specify the address. Different U-Boot
commands are inconsistent re: which of the two default values they use.
As such, set the two to the same value, and move the logic that does this
into tegra-common-post.h so it's not duplicated. A number of other non-
Tegra boards do this too.
The values chosen for these macros are no longer consistent with anything
in MEM_LAYOUT_ENV_SETTINGS. Regain consistency by setting $kernel_addr_r
to CONFIG_LOADADDR. Older scripts tend to use $loadaddr for the default
kernel load address, whereas newer scripts and features tend to use
$kernel_addr_r, along with other variables for other purposes such as
DTBs and initrds. Hence, it's logical they should share the same value.
I had originally thought to make the $kernel_addr_r and CONFIG_LOADADDR
have different values. This would guarantee no interference if a script
used the two variables for different purposes. However, that scenario is
unlikely given the semantic meaning associated with the two variables.
The lowest available value is 0x90200000; see comments for
MEM_LAYOUT_ENV_SETTINGS in tegra30-common-post.h for details. However,
that value would be problematic for a script that loaded a raw zImage to
$loadaddr, since it's more than 128MB beyond the start of SDRAM, which
would interfere with the kernel's CONFIG_AUTO_ZRELADDR. So, let's not do
that.
The only potential fallout I could foresee from this patch is if someone
has a script that loads the kernel to $loadaddr, but some other file
(DTB, initrd) to a hard-coded address that the new value of $loadaddr
interferes with. This seems unlikely. A user should not do that; they
should either hard-code all load addresses, or use U-Boot-supplied
variables for all load addresses. Equally, any fallout due to this change
is trivial to fix; simply modify the load addresses in that script.
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Paul Walmsley <pwalmsley@nvidia.com>
Reviewed-by: Simon Glass
Signed-off-by: Tom Warren <twarren@nvidia.com>
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:
- CONFIG_SYS_I2C_INIT_BOARD
- CONFIG_I2C_MULTI_BUS
- CONFIG_SYS_MAX_I2C_BUS
- CONFIG_SYS_I2C_SPEED
- CONFIG_SYS_I2C
This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1
It has not been tested on Tegra 114 as I don't have that board.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tegra's EHCI controllers only have a single PORTSC register. Configure
U-Boot to know this. This prevents e.g. ehci_shutdown() from touching
non-existent registers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
<asm/arch-tegra/tegra.h> needs to use CONFIG_TEGRA* to conditionalize
some definitions, since some modules moved between generations. Move
the definition of CONFIG_TEGRAnn to a header that's included earlier,
so that it's set by the time tegra.h needs to use it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix the timeout issue after running "bootp" command in U-Boot console.
TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10 after a
controller reset and before RUN bit is set (per technical reference
manual).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These are the board files for Venice2 (Tegra124), plus the AS3722 PMIC
files. PMIC init will be moved to pmic_common_init later.
This builds/boots on Venice2, SPI/MMC/USB/I2C all work. Audio, display
and WB/LP0 are not supported yet.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass
Stephen Warren
Jim Lin
Tom Warren