For odroid-c2 (arch-meson) for now disable designware eth as meson
now needs to do some harder GPIO work.
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
lib/efi_loader/efi_disk.c
Modified:
configs/odroid-c2_defconfig
Recently Linux is gaining support for efifb on AArch64 and that support actually
tries to make use of the frame buffer address we expose to it via gop.
While this wouldn't be bad in theory, in practice it means a few bad things
1) We expose 16bit frame buffers as 32bit today
2) Linux can't deal with overlapping non-PCI regions between efifb and
a different frame buffer driver
For now, let's just disable exposure of the frame buffer address. Most OSs that
get booted will have a native driver for the GPU anyway.
Signed-off-by: Alexander Graf <agraf@suse.de>
[trini: Remove line_len entirely]
Signed-off-by: Tom Rini <trini@konsulko.com>
We put the system table into our runtime services data section so that
payloads may still access it after exit_boot_services. However, most fields
in it are quite useless once we're in that state, so let's just patch them
out.
With this patch we don't get spurious warnings when running EFI binaries
anymore.
Signed-off-by: Alexander Graf <agraf@suse.de>
Some hardware that is supported by U-Boot can not handle DMA above 32bits.
For these systems, we need to come up with a way to expose the disk interface
in a safe way.
This patch implements EFI specific bounce buffers. For non-EFI cases, this
apparently was no issue so far, since we can just define our environment
variables conveniently.
Signed-off-by: Alexander Graf <agraf@suse.de>
This code does not currently build with driver model enabled for block
devices. Update it to correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
We can now successfully boot EFI applications from disk, but users
may want to also run them from a PXE setup.
This patch implements rudimentary network support, allowing a payload
to send and receive network packets.
With this patch, I was able to successfully run grub2 with network
access inside of QEMU's -M xlnx-ep108.
Signed-off-by: Alexander Graf <agraf@suse.de>
Add a simple version of this function for SPL. It does not check the buffer
size as this would add to the code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Rename 'w' to 'width' to make it more obvious what it is used for
- Use bool and int types instead of char to avoid register-masking on
32-bit machines
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
jetson-tk1 has 2 GB of RAM at 0x80000000, causing gd->ram_top to be zero.
Handle this by either avoiding ram_top or by using the same type as
ram_top to reverse the overflow effect.
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Call blk_dwrite to ensure that the block cache is notified
if enabled and remove build breakage when CONFIG_BLK is enabled.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
The EFI memory map does not need to be in a strict order, but 32bit
grub2 does expect it to be ascending. If it's not, it may try to
allocate memory inside the U-Boot data memory region.
We already sort the memory map in descending order, so let's just
reverse it when we pass it to a payload.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Andreas Färber <afaerber@suse.de>
The cache line flush helpers only work properly when they get aligned
start and end addresses. Round our flush range to cache line size. It's
safe because we're guaranteed to flush within a single page which has the
same cache attributes.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Andreas Färber <afaerber@suse.de>
Whenever we want to tell our payload about a path, we limit ourselves
to a reasonable amount of characters. So far we only passed in device
names - exceeding 16 chars was unlikely there.
However by now we also pass real file path information, so let's increase
the limit to 32 characters. That way common paths like "boot/efi/bootaa64.efi"
fit just fine.
Signed-off-by: Alexander Graf <agraf@suse.de>
When loading an el torito image, uEFI exposes said image as a raw
block device to the payload.
Let's do the same by creating new block devices with added offsets for
the respective el torito partitions.
Signed-off-by: Alexander Graf <agraf@suse.de>
The snippet of code to add a drive to our drive list needs to
get called from 2 places in the future. Split it into a separate
function.
Signed-off-by: Alexander Graf <agraf@suse.de>
To make the usage of this function more flexible, lets add the CRC start
value as parameter to this function. This way it can be used by other
functions requiring different start values than 0 as well.
For non-zero CRC start values to work, I've reworked the function a bit.
The new implementation is copied from the Linux version in
drivers/i2c/i2c-core.c / i2c_smbus_pec(). Which supports non-zero
CRC stating values.
I've double-checked that the results for zero starting values are
identical to the results from the original version of this function.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some EFI applications (grub2) expect that an allocation always returns
the highest available memory address for the given size.
Without this, we may run into situations where the initrd gets allocated
at a lower address than the kernel.
This patch fixes booting in such situations for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
We normally use __weak rather than calling it out directly as an alias.
Update this function to the normal method.
Signed-off-by: Tom Rini <trini@konsulko.com>
When switching between EFI context and U-Boot context we need to swap
the register that "gd" resides in.
Some functions slipped through here, with efi_allocate_pool / efi_free_pool
not doing the switch correctly and efi_return_handle switching too often.
Fix them all up to make sure we always have consistent register state.
Signed-off-by: Alexander Graf <agraf@suse.de>
The EFI standard defines a simple boot protocol that an EFI payload can use
to access video output.
This patch adds support to expose exactly that one (and the mode already in
use) as possible graphical configuration to an EFI payload.
With this, I can successfully run grub2 with graphical output.
Signed-off-by: Alexander Graf <agraf@suse.de>
Since dhry_per_sec is a u64 we must also use lldiv here when working
with it. Otherwise:
../lib/dhry/cmd_dhry.c:(.text.do_dhry+0xd8): undefined reference to `__udivdi3'
On some platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is not needed now that the memory controller driver has the SPD data
in its own node.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present samus reports about 5600 DMIPS. With the default iteration count
this is OK, but if 10 million runs are performed it overflows. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't need this anymore - we can use device tree and the new pinconfig
driver instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
EFI payloads can query for the device they were booted from. Because
we have a disconnect between loading binaries and running binaries,
we passed in a dummy device path so far.
Unfortunately that breaks grub2's logic to find its configuration
file from the same device it was booted from.
This patch adds logic to have the "load" command call into our efi
code to set the device path to the one we last loaded a binary from.
With this grub2 properly detects where we got booted from and can
find its configuration file, even when searching by-partition.
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that we have all the bits and pieces ready for EFI payload loading
support, hook them up in Makefiles and KConfigs so that we can build.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
[trini: Enable only when we of OF_LIBFDT, disable on kwb and colibri_pxa270]
Signed-off-by: Tom Rini <trini@konsulko.com>
The EFI loader needs to maintain views of memory - general system memory
windows as well as used locations inside those and potential runtime service
MMIO windows.
To manage all of these, add a few helpers that maintain an internal
representation of the map the similar to how the EFI API later on reports
it to the application.
For allocations, the scheme is very simple. We basically allow allocations
to replace chunks of previously done maps, so that a new LOADER_DATA
allocation for example can remove a piece of the RAM map. When no specific
address is given, we just take the highest possible address in the lowest
RAM map that fits the allocation size.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Simon Glass <sjg@chromium.org>
A EFI applications usually want to access storage devices to load data from.
This patch adds support for EFI disk interfaces. It loops through all block
storage interfaces known to U-Boot and creates an EFI object for each existing
one. EFI applications can then through these objects call U-Boot's read and
write functions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
[trini: Update for various DM changes since posting]
Signed-off-by: Tom Rini <trini@konsulko.com>
After booting has finished, EFI allows firmware to still interact with the OS
using the "runtime services". These callbacks live in a separate address space,
since they are available long after U-Boot has been overwritten by the OS.
This patch adds enough framework for arbitrary code inside of U-Boot to become
a runtime service with the right section attributes set. For now, we don't make
use of it yet though.
We could maybe in the future map U-boot environment variables to EFI variables
here.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
One of the basic EFI interfaces is the console interface. Using it an EFI
application can interface with the user. This patch implements an EFI console
interface using getc() and putc().
Today, we only implement text based consoles. We also convert the EFI Unicode
characters to UTF-8 on the fly, hoping that everyone managed to jump on the
train by now.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
When an EFI application runs, it has access to a few descriptor and callback
tables to instruct the EFI compliant firmware to do things for it. The bulk
of those interfaces are "boot time services". They handle all object management,
and memory allocation.
This patch adds support for the boot time services and also exposes a system
table, which is the point of entry descriptor table for EFI payloads.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
EFI uses the PE binary format for its application images. Add support to EFI PE
binaries as well as all necessary bits for the "EFI image loader" interfaces.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The original name of this function is unclear. This patch renames this
CRC16 function to crc16_ccitt() matching its name with its
implementation.
To make the usage of this function more flexible, lets add the CRC start
value as parameter to this function. This way it can be used by other
functions requiring different start values than 0 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add an option to enable libfdt in SPL. This can be useful when decoding
FIT files in SPL.
We need to make sure this option is not enabled in SPL by this change.
Also this option needs to be enabled in host builds. Si add a new
IMAGE_USE_LIBFDT #define which can be used in files that are built on the
host but must also build for U-Boot and SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
Use 'struct' instead of a typdef. Also since 'struct block_dev_desc' is long
and causes 80-column violations, rename it to struct blk_desc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The existing function to add a new property to a tree being built requires
that the entire contents of the new property be passed in. For some
applications it is more convenient to be able to add the property contents
later, perhaps by reading from a file. This avoids double-buffering of the
contents.
Add a new function to support this and adust the existing fdt_property() to
use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases the timer must be accessible before driver model is active.
Examples include when using CONFIG_TRACE to trace U-Boot's execution before
driver model is set up. Enable this option to use an early timer. These
functions must be supported by your timer driver: timer_early_get_count()
and timer_early_get_rate().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function can be called from the timer code on instrumented functions.
Mark it as 'notrace' so that it doesn't cause infinite recursion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust the driver to use driver model. The SOR becomes a bridge device. We
use the normal simple_panel driver to handle the display itself. We also
need to enable some options such as regulators, PWMs and DM_VIDEO itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
If BUILD_TAG is part of KBUILD_CFLAGS, then any time the value changes,
all files get rebuilt. In a continuous integration environment, the value
will change every build. This wastes time, assuming that incremental
builds would otherwise occur.
To solve this, remove BUILD_TAG from KBUILD_CFLAGS and add it to CFLAGS
for just the one file that uses it. This does have the disadvantage that
if any other files want to use the flag, we'll need to duplicate this
custom CFLAGS setup logic. However, it seems unlikely we'll need this.
An alternative would be to add BUILD_TAG to the "local version" and remove
the special case code from display_options.c. However, that would affect
the format of the U-Boot signon message, which may negatively affect
people looking for specific data there. The approach of using
file-specific CFLAGS was suggested by Masahiro Yamada.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini
Alexander Graf
Simon Glass
Andreas Bießmann
Andreas Färber
Eric Nelson
Stefan Roese
Masahiro Yamada
Bin Meng
Stephen Warren