Commit graph

38 commits

Author SHA1 Message Date
Marek Vasut
5368c55d4c COMMON: Use __stringify() instead of MK_STR()
Kill multiple occurances and redeclaration of MK_STR
in favor of __stringify().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15 11:53:47 -07:00
Tom Rini
219f4788d3 hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-06-20 20:36:51 +02:00
Joe Hershberger
7d6a098219 mpc83xx: Cleanup usage of LBC constants
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:56 -05:00
Joe Hershberger
2fef402097 mpc83xx: Cleanup usage of DDR constants
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:55 -05:00
Joe Hershberger
72cd4087c9 mpc83xx: Cleanup usage of BAT constants
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:55 -05:00
Joe Hershberger
b2773a5e1c mpc83xx: cosmetic: MVBLM7.h checkpatch compliance
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-03 18:27:54 -05:00
Mike Frysinger
31a4f1e5b6 board configs: drop NET_MULTI references
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00
Wolfgang Denk
25ddd1fb0a Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:05:30 +02:00
Wolfgang Denk
553f09823c Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE
CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE

No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.

Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken.  Last known maintainers on Cc:

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:03:25 +02:00
Andre Schwarz
116ef54d68 MVBLM7: make TSEC2 work again.
SICRH has been misconfigured, i.e. TSEC2 clock + D[0:3] are GPIOs.
Fix this to be RGMII signals again.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
2010-10-23 22:12:16 +02:00
Peter Tyser
d98b0523cf powerpc: Cleanup BOOTFLAG_* references
Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.

Note that this change makes the board info bd_bootflags field useless.
It will always be set to 0, but we leave it around so that we don't
break the board info structure that some OSes are expecting to be passed
from U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-18 22:38:56 +02:00
Wolfgang Denk
2ae1824196 Makefile: move all Power Architecture boards into boards.cfg
Clean up Makefile, and drop a lot of the config.mk files on the way.

We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:12:04 +02:00
Wolfgang Denk
14d0a02a16 Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:07:10 +02:00
Ira W. Snyder
9f530d59e6 e300: increase CONFIG_SYS_BOOTMAPSZ to allow booting large kernels
Newer Linux kernels can overrun the initial memory window used for
booting with their BSS area. When this happens, they overwrite the FDT
and silently fail to boot.

On e300 CPUs, the Linux kernel uses an initial BAT covering the first
256MB of RAM. See arch/powerpc/kernel/head_32.S for details. Increase
the value of CONFIG_SYS_BOOTMAPSZ to accommodate the maximum value
allowed by Linux. This will allow very large kernels to boot.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-09-23 21:13:32 +02:00
Stefan Roese
24956642ef Remove unused CONFIG_SERIAL_SOFTWARE_FIFO feature
This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2010-09-23 09:02:05 +02:00
Andre Schwarz
fd194f82d1 mpc83xx/mvBLM7: add usb commands and cleanup.
Add USB commands.
Rename autoscript to bootscript.
Add automatic bootscript image generation to makefile.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-05-07 12:20:15 -05:00
Kim Phillips
1a2e203b31 mpc83xx: turn on icache in core initialization to improve u-boot boot time
before, MPC8349ITX boots u-boot in 4.3sec:

        column1 is elapsed time since first message
        column2 is elapsed time since previous message
        column3 is the message
0.000 0.000: U-Boot 2010.03-00126-gfd4e49c (Apr 11 2010 - 17:25:29) MPC83XX
0.000 0.000:
0.000 0.000: Reset Status:
0.000 0.000:
0.032 0.032: CPU:   e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.032 0.000: Board: Freescale MPC8349E-mITX
0.032 0.000: UPMA:  Configured for compact flash
0.032 0.000: I2C:   ready
0.061 0.028: DRAM:  256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
1.516 1.456: FLASH: 16 MB
2.641 1.125: PCI:   Bus Dev VenId DevId Class Int
2.652 0.011:         00  10  1095  3114  0180  00
2.652 0.000: PCI:   Bus Dev VenId DevId Class Int
2.652 0.000: In:    serial
2.652 0.000: Out:   serial
2.652 0.000: Err:   serial
2.682 0.030: Board revision: 1.0 (PCF8475A)
3.080 0.398: Net:   TSEC1: No support for PHY id ffffffff; assuming generic
3.080 0.000: TSEC0, TSEC1
4.300 1.219: IDE:   Bus 0: .** Timeout **

after, MPC8349ITX boots u-boot in 3.0sec:

0.010 0.010: U-Boot 2010.03-00127-g4b468cc-dirty (Apr 11 2010 - 17:47:29) MPC83XX
0.010 0.000:
0.010 0.000: Reset Status:
0.010 0.000:
0.017 0.007: CPU:   e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.017 0.000: Board: Freescale MPC8349E-mITX
0.038 0.020: UPMA:  Configured for compact flash
0.038 0.000: I2C:   ready
0.038 0.000: DRAM:  256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
0.260 0.222: FLASH: 16 MB
1.390 1.130: PCI:   Bus Dev VenId DevId Class Int
1.390 0.000:         00  10  1095  3114  0180  00
1.390 0.000: PCI:   Bus Dev VenId DevId Class Int
1.400 0.010: In:    serial
1.400 0.000: Out:   serial
1.400 0.000: Err:   serial
1.400 0.000: Board revision: 1.0 (PCF8475A)
1.832 0.432: Net:   TSEC1: No support for PHY id ffffffff; assuming generic
1.832 0.000: TSEC0, TSEC1
3.038 1.205: IDE:   Bus 0: .** Timeout **

also tested on these boards (albeit with a less accurate
boottime measurement method):

seconds: before  after
8349MDS  ~2.6    ~2.2
8360MDS  ~2.8    ~2.6
8313RDB  ~2.5    ~2.3 #nand boot
837xRDB  ~3.1    ~2.3

also tested on an 8323ERDB.

v2: also remove the delayed icache enablement assumption in arch ppc's
board.c, and add a CONFIG_MPC83xx define in the ITX config file for
consistency (even though it was already being defined in 83xx'
config.mk).

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-04-22 18:44:56 -05:00
Kim Phillips
a059e90e16 mpc83xx: enable command line autocompletion
because it's convenient.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-04-22 18:34:49 -05:00
Kim Phillips
c7190f028f mpc83xx: retain POR values of non-configured ACR, SPCR, SCCR, and LCRR bitfields
some LCRR bits are not documented throughout the 83xx family RMs.
New board porters copying similar board configurations might omit
setting e.g., DBYP since it was not documented in their SoC's RM.

Prevent them bricking their board by retaining power on reset values
in bit fields that the board porter doesn't explicitly configure
via CONFIG_SYS_<registername>_<bitfield> assignments in the board
config file.

also move LCRR assignment to cpu_init_r[am] to help ensure no
transactions are being executed via the local bus while CLKDIV is being
modified.

also start to use i/o accessors.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-09-26 21:19:38 -05:00
Peter Tyser
3202d33169 Remove deprecated 'autoscr' command/variables
The more standard 'source' command provides identical functionality to
the autoscr command.

Environment variable names/values on the MVBC_P, MVBML7, kmeter1,
mgcoge, and km8xx boards are updated to no longer refernce 'autoscr'.

The 'autoscript' and 'autoscript_uname' environment variables are
also removed.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Heiko Schocher <hs@denx.de>
2009-09-22 23:03:24 +02:00
André Schwarz
28887d831b Use common code for Matrix Vision boards
Clean up existing boards (mvBC-P/MPC5200 and mvBL-M7/MPC8343) by
using common code.

Signed-off-by: Andr Schwarz <andre.schwarz@matrix-vision.de>
2009-08-28 00:31:23 +02:00
Kim Phillips
be9b56df02 mpc83xx: CONFIG_83XX_GENERIC_PCI is now synonymous with CONFIG_PCI; remove the former
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-27 10:17:54 -05:00
Timur Tabi
890d242fac remove _IO_BASE and KSEG1ADDR from board configuration files
The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet
driver, but the code that used that macro was removed over a year
ago, so board configuration files no longer need to define it.

The _IO_BASE macro is also automatically defined to 0 if it isn't
already set, so there's no need to define that macro either in the
board configuration files.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-11 00:19:16 +02:00
Peter Tyser
2c7920afaf 83xx: Replace CONFIG_MPC83[0-9]X with MPC83[0-9]x
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-06-12 20:47:17 +02:00
Peter Tyser
0f89860494 83xx: Replace CONFIG_MPC83XX with CONFIG_MPC83xx
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-06-12 20:47:17 +02:00
Peter Tyser
d48eb5131d i2c: Remove deprecated individual i2c commands
The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.

The functionality of the individual commands is still available via
the 'i2c' command.

This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-06-12 20:39:46 +02:00
Wolfgang Denk
74de7aefd7 Add "source" command; prepare removal of "autoscr" command
According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.

This patch prepares this change and starts a 6 month transition
period as follows:

- The new "source" command has been added, which implements exactly
  the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
  new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
  have *not* been adapted yet; these will be renamed resp. removed in
  a separate patch when the support for the "autoscr" command get's
  finally dropped.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-04-03 22:01:42 +02:00
Scott Wood
c123098035 mpc83xx: Set guarded bit on BAT that covers the end of the address space
The mpc8313erdb board currently sets DBAT6 to cover all of the final 256MiB of
address space; however, not all of this space is covered by a device.  In
particular, flash sits at 0xfe000000-0xfe7fffff, and nothing is mapped
at the far end of the address space.

In zlib, there is a loop that references p[-1] if p is non-NULL.  Under
some circumstances, this leads to the CPU speculatively loading from
0xfffffff8 if p is NULL.  This leads to a machine check.

Signed-off-by: Scott Wood <scottwood@freescale.com>

continuation to the remaining mpc83xx boards that suffer from the same problem.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-04-01 16:48:57 -05:00
Jon Loeliger
801a194616 Removed unused CONFIG_L1_INIT_RAM symbol.
Prevent further viral propogation of the unused
symbol CONFIG_L1_INIT_RAM by just removing it.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
2008-12-01 10:28:50 -06:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Jean-Christophe PLAGNIOL-VILLARD
0e8d158664 rename CFG_ENV macros to CONFIG_ENV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:06 +02:00
Jean-Christophe PLAGNIOL-VILLARD
5a1aceb068 rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:04 +02:00
Andre Schwarz
1a9eeb78b8 change mvBL-M7 default env and move to vendor subdir
fix mvBL-M7 config and move to matrix_vision subdir

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-08-25 17:11:20 -05:00
Jean-Christophe PLAGNIOL-VILLARD
00b1883a4c drivers/mtd: Move conditional compilation to Makefile
rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:42 +02:00
Andre Schwarz
5ed546fdd0 update mvBL-M7 board config
update mvBL-M7 config file to use UBOOT_VERSION and define
CONFIG_HIGH_BATS.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
2008-07-07 00:30:20 +02:00
Wolfgang Denk
e093a24762 Coding Style Cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-06-28 23:34:37 +02:00
Kim Phillips
2329fe113d mpc83xx: MVBLM7: minor build fixups
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-06-10 13:34:27 -05:00
Andre Schwarz
c005b93925 add MPC8343 based board mvBlueLYNX-M7 (doc+config)
Add MPC8343 based board mvBlueLYNX-M7.
It's a single board stereo camera system.
Please read doc/README.mvblm7 for details.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-06-10 12:52:57 -05:00