Commit graph

23 commits

Author SHA1 Message Date
Gong Qianyu
18fb0e3cae common/board_f.c: change the macro name and remove it for PPC platforms
For most PPC platforms, they will call the first get_clocks() in
init_sequence_f[] as they define CONFIG_PPC. CONFIG_SYS_FSL_CLK is
then defined to call the second get_clocks(), which should be
redundant for PPC.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:33:58 -07:00
Gong Qianyu
677f970bc6 common/board_f.c: modify the macro to use get_clocks() more common
get_clocks() should not be limited by ESDHC.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
2015-10-24 13:50:38 -04:00
Masahiro Yamada
09f3ca3dd5 arm, powerpc: select SYS_GENERIC_BOARD
We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-10-24 13:50:38 -04:00
Bin Meng
a726075911 cmd: Convert CONFIG_CMD_ELF to Kconfig
Convert CONFIG_CMD_ELF to Kconfig and tidy up affected boards.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-10-21 07:46:25 -06:00
York Sun
b3142e2cf8 powerpc: configs: Fix init_ram physical address for several boards
For e6500 and e5500 SoCs, it was intended to put init_ram address in
ccsr reserved space. It is no longer true since SerDes module took the
space. Move it to another reserved space at CCSR + 0x03c000.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-09-01 20:42:54 -05:00
Simon Glass
a77fda1f7d net: Move CONFIG_E1000 options to Kconfig
Move config for the E1000 Ethernet driver to Kconfig and tidy up affected
boards.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-08-21 16:40:23 -05:00
Joe Hershberger
ef0f2f5752 Move defaults from config_cmd_default.h to Kconfig
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25 22:18:34 -04:00
Joe Hershberger
c9bb942e2f Move default y configs out of arch/board Kconfig
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.

Remove the configs that behave this way from the archs.

A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:

SPIFLASH
DISPLAY_BOARDINFO

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25 22:17:55 -04:00
Lars Poeschel
42eccdd650 configs: remove CONFIG_NET_MULTI
CONFIG_NET_MULTI is not used anywhere and thus can safely be removed
from the configs.

Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
2015-06-02 11:12:32 -04:00
Joe Hershberger
6eed3786c6 net: Move the CMD_NET config to defconfigs
This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2015-06-01 09:40:15 -05:00
Joe Hershberger
7453cb595c Move setexpr to Kconfig
Another shell scripting command that has not been moved.

Moved using tools/moveconfig.py using these settings:

CMD_SETEXPR bool n y

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-06-01 09:39:29 -05:00
Chunhe Lan
373762c34c powerpc/t4rdb: Add SD boot support for T4240RDB board
This patch adds SD boot support for T4240RDB board. SPL
framework is used. PBL initializes the internal RAM and
copies SPL to it. Then SPL initializes DDR using SPD and
copies u-boot from SD card to DDR, finally SPL transfers
control to u-boot.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: Fix T4240RDB_SDCARD_defcofig]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:24:04 -07:00
Chunhe Lan
a8efe79c0b T4240RDB: Enable CONFIG_SYS_CORTINA_FW_IN_NOR config
Now cortina driver uses macro CONFIG_SYS_CORTINA_FW_IN_NOR
to define that firmware of cortina driver is stored in the
nor flash.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-20 10:15:29 -07:00
Peter Tyser
073adf987e nand: Remove CONFIG_MTD_NAND_VERIFY_WRITE
The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some
time and a more generic method of NAND verification now exists in U-Boot.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2015-03-30 23:24:39 -05:00
Jeffrey Ladouceur
3fa66db459 mpc85xx: inhibit qman and bman portals by default
Not all portals might be managed and therefore visible.
Set the isdr register so that the corresponding isr register
won't be set. This is required when supporting power management.

Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-15 09:16:07 -08:00
Chunhe Lan
9a509cf66a powerpc/t4240rdb: Convert to use generic board code
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-15 09:14:58 -08:00
Xiaobo Xie
929dfdc26a powerpc/t4240rdb: enable eSDHC 3.3V support
The SD supply Voltage was 3.3V on T4240RDB, so enabled 3.3V support for eSDHC.

Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Wujie Qiu <B49553@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:16 -08:00
Chunhe Lan
1b5c2b5133 powerpc/t4rdb: Fix CPLD timing
This fixes CPLD timing from previous commit
ab06b236f7.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: This is the difference between v2 and v1 patch]
Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-19 10:28:30 -08:00
Chunhe Lan
ab06b236f7 powerpc/t4rdb: Add support of CPLD
This support of CPLD includes

    - Files and register definitions
    - Command to switch alternate bank
    - Command to switch default bank

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-14 11:12:14 -08:00
Ruchika Gupta
789490b6c0 mpc85xx: configs - Enable blob command in freescale platforms
Enable blob commands for platforms having SEC 4.0 or greater
for secure boot scenarios

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-10-16 14:21:09 -07:00
Ruchika Gupta
737537ef0c mpc85xx: configs - Add hash command in freescale platforms
Enable CAAM in platforms supporting the hardware block.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-10-16 14:17:21 -07:00
Chunhe Lan
1a344456a9 powerpc/85xx: Add T4160RDB board support
T4160RDB shares the same platform as T4240RDB. T4160 is
a low power version of T4240, with the eight e6500 cores,
two DDR3 controllers, and same peripheral bus interfaces.

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:24:26 -05:00
Chunhe Lan
0b2e13d9cc powerpc/85xx: Add T4240RDB board support
T4240RDB board Specification
----------------------------
Memory subsystem:
   6GB DDR3
   128MB NOR flash
   2GB NAND flash

Ethernet:
   Eight 1G SGMII ports
   Four 10Gbps SFP+ ports

PCIe:
   Two PCIe slots

USB:
   Two USB2.0 Type A ports

SDHC:
   One SD-card port

SATA:
   One SATA port

UART:
   Dual RJ45 ports

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
2014-05-13 08:24:32 -07:00