Beaglebone uses SMSC PHY which works incorrectly with generic PHY
driver so enable SMSC PHY driver to fix networking problems on
Beaglebone.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
The total RAM size of the IGEP-based boards is 512MiB not 1GiB, the
LPDDR memory consist on two dies of 256MiB.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
For the DA8xx family of SoCs, the set_cpu_clk_info() function was not
initialising the DSP frequency, leading to 'bdinfo' command output such as:
[...snip...]
ARM frequency = 300 MHz
DSP frequency = -536870913 MHz
DDR frequency = 300 MHz
This commit provides a separate implementation of set_cpu_clk_info() for
the DA8xx SoCs that initialises the DSP frequency to zero (since
currently the DSP is not enabled by U-Boot on any DA8xx platform). The
separate implementation is justified because there is no common code
between DA8xx and the other SoC families. It is now much easier to
understand the flow of the two separate functions.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Hadli, Manjunath <manjunath.hadli@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Replace a magic number for the DDR2/mDDR PHY clock ID with a proper
definition. In addition, don't request this clock ID on DA830 hardware,
which does not have a DDR2/mDDR PHY (or associated PLL controller).
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
On the DA830, UART2's clock is derived from PLL controller 0 output 2.
On the DA850, it is in the ASYNC3 group, and may be switched between PLL
controller 0 or 1. Fix the definition of the ID to match.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Tidy up the clock IDs defined for the DA8xx SOCs. With this new structure in
place, it is clear how to define new clock IDs, and how these map to the
numbers presented in the technical reference manual.
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Cc: Tom Rini <trini@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This fixes the breakage with SPL on most OMAP boards after the GPIO
driver was moved.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h>
- Make some defines a little less generic now.
- Pinmux must be done by done by SPL now.
- Create 3 pinmux functions, uart0, i2c0 and board.
- Add pinmux specific to Starter Kit EVM for MMC now.
Signed-off-by: Tom Rini <trini@ti.com>
- Board requires gpio0 #7 to be set to power DDR3.
- Board uses DDR3, add a way to determine which DDR type to call
config_ddr with.
- Both of the above require filling in the header structure early, move
it into the data section.
Signed-off-by: Tom Rini <trini@ti.com>
The intention has always been (and boards are to support) an i2c EEPROM
that will identify what hardware they are, allowing a single binary to
support multiple boards. As such, remove the 'evm.c' file as there is
nothing EVM centric in it currently, only SoC peripheral configuration.
Signed-off-by: Tom Rini <trini@ti.com>
In order to support DDR3 as well as DDR2, we need to perform the same
init sequence, but with different values. So change config_ddr() to
toggle setting pointers/etc for what DDR2 wants, and then calling.
Signed-off-by: Tom Rini <trini@ti.com>
The ddr_regs struct was incorrectly offset after the dt0wiratio0 entry.
Correct this by documenting a missing register that will be used at some
point in the future (when write leveling is supported). Further, the
cmdNcs{force,delay} fields are undocumented and we have been setting
them to zero, remove. Next, setting of the
'DATAn_REG_PHY_USE_RANK0_DELAYS field belongs with the rest of the
ddr_data entries, so program it there. Finally, comment on how we are
configuring the DATA1 registers that correspond to the DATA0 (dt0)
registers defined in the struct.
Signed-off-by: Tom Rini <trini@ti.com>
The various ratio1 fields are not documented in any of the documentation
I can find. Removing these and testing has yielded success, so remove
the code that sets them and move their locations into the reserved
fields.
Signed-off-by: Tom Rini <trini@ti.com>
This function sets a number of related registers to the same value (the
registers in question all have the same field descriptions and are
related in operation). Rather than defining a struct and setting the
value repeatedly, just pass in the value.
Signed-off-by: Tom Rini <trini@ti.com>
Rather than defining our own structs to note what to use when
programming the EMIF and related re-use the emif_regs struct.
Signed-off-by: Tom Rini <trini@ti.com>
A number of memory initalization functions were int and always returned
0. Further it's not feasible to be doing error checking here, so simply
turn them into void functions.
Signed-off-by: Tom Rini <trini@ti.com>
- Remove the call to set ddrctrl->ddrioctrl as it's all zeros.
- Comment what we're really setting in ddrctrl->ddrckectrl which is that
we're operating in the normal mode where EMIF/PHY clock is controlled
by the PHY.
Signed-off-by: Tom Rini <trini@ti.com>
EMIF parameters are calculated based on the AC timing
parameters from the SDRAM datasheet and the DDR frequency.
Current values for these paramters in AM335x U-Boot code,
though reliable, are not fully optimal. The most optimal
settings can be derived based on the guidelines published
at [1]. A pre-computed set of values with the most optimum
settings for AM335x EVM and BeagleBone can be found at [2].
[1] http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
[2] http://processors.wiki.ti.com/index.php/OMAP_and_Sitara_CCS_support#AM335x
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Depending on if we have DDR2 or DDR3 on the board we will need to call
ddr_pll_config with a different value. This call can be delayed
slightly to the point where we know which type of memory we have.
Signed-off-by: Tom Rini <trini@ti.com>
We need to pass in the type of memory that is connected to the board.
The only reliable way to do this is to know what type of board we are
running on (which later will be knowable in s_init()). For now, pass in
the value of DDR2.
Signed-off-by: Tom Rini <trini@ti.com>
Rework the EMIF4/DDR code slightly to setup the structs that
config_cmd_ctrl and config_ddr_data take to be setup at compile time and
mark them as const. This lets us simplify the calling path slightly as
well as making it easier to deal with DDR3.
Signed-off-by: Tom Rini <trini@ti.com>
With the previous bugfix we now don't need to set two different REF_CTRL
values and instead set the final value.
Signed-off-by: Tom Rini <trini@ti.com>
When we change SDRAM_CONFIG this triggers a refresh based on all of the
parameters that we have programmed so we must do this last.
Signed-off-by: Tom Rini <trini@ti.com>
We do not need to check for EMIF_GCLK and L3_GCLK being active. This
was a hold-over from bringup and no longer required.
Signed-off-by: Tom Rini <trini@ti.com>
- Add default commands
- Add HUSH parser
- Make environment, malloc areas larger
- Add ATAGS and OF_LIBFDT
- Add defaults to boot ramdisk and MMC, use uEnv.txt
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds SPL support for IGEP-based boards.
Tested on an IGEPv2 Rev.C board with Micron NAND Flash memory.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
IGEP-based boards can have two different flash memories, a OneNAND or a
NAND device. Add a configuration option for to choose which memory to use.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
This patch adds board-specific initialization for CPSW on
TI AM335X based boards. Tested on BeagleBone.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split board-specific part into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Read the on-board EEPROM during startup to detect the version
of the board we are running on (as for now only BeagleBone vs
EVM detection is supported).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch adds pin mux settings for CPSW switch found on
TI AM335X based boards (MII and RGMII modes).
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split pinmux into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch adds platform-specific initialization for CPSW
switch on TI AM33XX SoCs.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split init out of original patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
CPSW is an on-chip ethernet switch that is found on various SoCs from Texas
Instruments. This patch adds a simple driver (based on the Linux driver) for
this hardware module.
This patch also adds support to clean and flush dcache during packet send
and receive.
Changes by Sandhya: Added support to clean and flush dcache during packet
send/receive and added timeouts.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
[Ilya: Cleaned cache handling, some style cleanup, some small
fixes, use of internal RAM for descriptors]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
also fix NS16550_init() as we need 16x divider
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Sughosh Ganu <urwithsughosh@gmail.com>
follow section 15.2.13.1 (Initializing Following Device Power Up or Reset) of
OMAP-L138 DSP+ARM Processor Technical Reference Manual
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
This reverts commit 5347560f5427bcdd48a563b62180481606ac8044,
which was applied only to get release 2012.07 functional on as
many ARM targets as possible despite mis-aligned accesses.
Andreas Bießmann
Ilya Yanok
Enric Balletbò i Serra
Laurence Withers
Tom Rini
Marek Vasut
Vaibhav Bedia
Javier Martinez Canillas
Chandan Nath
Cyril Chemparathy
Peter Meerwald
Mikhail Kshevetskiy
Albert ARIBAUD
Steve Sakoman