u-boot/include/configs/highbank.h
Rob Herring 32b4a8a2a5 ARM: highbank: remove DRAM bank setup
On the highbank platform the SoC's management controller firmware
will probe the DRAM modules and populates the initial device tree with
the correct values. Therefore the memory sizes in the DT are already
correct, so remove U-Boot's DRAM bank setup so the memory node is not
"fixed up" by u-boot.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andre Przywara <osp@andrep.de>
2015-08-12 12:08:19 -04:00

99 lines
2.5 KiB
C

/*
* Copyright 2010-2011 Calxeda, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <config_distro_defaults.h>
#define CONFIG_SYS_DCACHE_OFF
#define CONFIG_SYS_THUMB_BUILD
#define CONFIG_SYS_NO_FLASH
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_FIT
#define CONFIG_SYS_BOOTMAPSZ (16 << 20)
#define CONFIG_SYS_TIMER_RATE (150000000/256)
#define CONFIG_SYS_TIMER_COUNTER (0xFFF34000 + 0x4)
#define CONFIG_SYS_TIMER_COUNTS_DOWN
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
#define CONFIG_PL011_SERIAL
#define CONFIG_PL011_CLOCK 150000000
#define CONFIG_PL01x_PORTS { (void *)(0xFFF36000) }
#define CONFIG_CONS_INDEX 0
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTCOUNT_LIMIT
#define CONFIG_SYS_BOOTCOUNT_SINGLEWORD
#define CONFIG_SYS_BOOTCOUNT_LE /* Use little-endian accessors */
#define CONFIG_SYS_BOOTCOUNT_ADDR 0xfff3cf0c
#define CONFIG_MISC_INIT_R
#define CONFIG_LIBATA
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 5
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
#define CONFIG_CALXEDA_XGMAC
/*
* Command line configuration.
*/
#define CONFIG_CMD_SCSI
#define CONFIG_BOOT_RETRY_TIME -1
#define CONFIG_RESET_TO_RETRY
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_LOAD_ADDR 0x800000
#define CONFIG_SYS_64BIT_LBA
/*-----------------------------------------------------------------------
* Physical Memory Map
* The DRAM is already setup, so do not touch the DT node later.
*/
#define CONFIG_NR_DRAM_BANKS 0
#define PHYS_SDRAM_1_SIZE (4089 << 20)
#define CONFIG_SYS_MEMTEST_START 0x100000
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1_SIZE - 0x100000)
/* Environment data setup
*/
#define CONFIG_ENV_IS_IN_NVRAM
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfff88000 /* NVRAM base address */
#define CONFIG_SYS_NVRAM_SIZE 0x8000 /* NVRAM size */
#define CONFIG_ENV_SIZE 0x2000 /* Size of Environ */
#define CONFIG_ENV_ADDR CONFIG_SYS_NVRAM_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_TEXT_BASE 0x00008000
#define CONFIG_SYS_INIT_SP_ADDR 0x01000000
#define CONFIG_SKIP_LOWLEVEL_INIT
#endif