u-boot/include/ns87308.h
Wolfgang Denk 1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00

235 lines
7.6 KiB
C

/*
* (C) Copyright 2000
* Rob Taylor, Flying Pig Systems. robt@flyingpig.com.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _NS87308_H_
#define _NS87308_H_
#include <asm/pci_io.h>
/* Note: I couldn't find a full data sheet for the ns87308, but the ns87307 seems to be pretty
functionally- (and pin-) equivalent to the 87308, but the 308 has better ir support. */
void initialise_ns87308(void);
/*
* The following struct represents the GPIO registers on the NS87308/NS97307
*/
struct GPIO
{
unsigned char dta1; /* 0 data port 1 */
unsigned char dir1; /* 1 direction port 1 */
unsigned char out1; /* 2 output type port 1 */
unsigned char puc1; /* 3 pull-up control port 1 */
unsigned char dta2; /* 4 data port 2 */
unsigned char dir2; /* 5 direction port 2 */
unsigned char out2; /* 6 output type port 2 */
unsigned char puc2; /* 7 pull-up control port 2 */
};
/*
* The following represents the power management registers on the NS87308/NS97307
*/
#define PWM_FER1 0 /* 0 function enable reg. 1 */
#define PWM_FER2 1 /* 1 function enable reg. 2 */
#define PWM_PMC1 2 /* 2 power mgmt. control 1 */
#define PWM_PMC2 3 /* 3 power mgmt. control 2 */
#define PWM_PMC3 4 /* 4 power mgmt. control 3 */
#define PWM_WDTO 5 /* 5 watchdog time-out */
#define PWM_WDCF 6 /* 6 watchdog config. */
#define PWM_WDST 7 /* 7 watchdog status */
/*PNP config registers:
* these depend on the stated of BADDR1 and BADDR0 on startup
* so there's three versions here with the last two digits indicating
* for which configuration their valid
* the 1st of the two digits indicates the state of BADDR1
* the 2st of the two digits indicates the state of BADDR0
*/
#define IO_INDEX_OFFSET_0x 0x0279 /* full PnP isa Mode */
#define IO_INDEX_OFFSET_10 0x015C /* PnP motherboard mode */
#define IO_INDEX_OFFSET_11 0x002E /* PnP motherboard mode */
#define IO_DATA_OFFSET_0x 0x0A79 /* full PnP isa Mode */
#define IO_DATA_OFFSET_10 0x015D /* PnP motherboard mode */
#define IO_DATA_OFFSET_11 0x002F /* PnP motherboard mode */
#if defined(CONFIG_SYS_NS87308_BADDR_0x)
#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_0x)
#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_0x)
#elif defined(CONFIG_SYS_NS87308_BADDR_10)
#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_10)
#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_10)
#elif defined(CONFIG_SYS_NS87308_BADDR_11)
#define IO_INDEX (CONFIG_SYS_ISA_IO + IO_INDEX_OFFSET_11)
#define IO_DATA (CONFIG_SYS_ISA_IO + IO_DATA_OFFSET_11)
#endif
/* PnP register definitions */
#define SET_RD_DATA_PORT 0x00
#define SERIAL_ISOLATION 0x01
#define CONFIG_CONTROL 0x02
#define WAKE_CSN 0x03
#define RES_DATA 0x04
#define STATUS 0x05
#define SET_CSN 0x06
#define LOGICAL_DEVICE 0x07
/*vendor defined values */
#define SID_REG 0x20
#define SUPOERIO_CONF1 0x21
#define SUPOERIO_CONF2 0x22
#define PGCS_INDEX 0x23
#define PGCS_DATA 0x24
/* values above 30 are different for each logical device
but I can't be arsed to enter them all. the ones here
are pretty consistent between all logical devices
feel free to correct the situation if you want.. ;)
*/
#define ACTIVATE 0x30
#define ACTIVATE_OFF 0x00
#define ACTIVATE_ON 0x01
#define BASE_ADDR_HIGH 0x60
#define BASE_ADDR_LOW 0x61
#define LUN_CONFIG_REG 0xF0
#define DBASE_HIGH 0x60 /* SIO KBC data base address, 15:8 */
#define DBASE_LOW 0x61 /* SIO KBC data base address, 7:0 */
#define CBASE_HIGH 0x62 /* SIO KBC command base addr, 15:8 */
#define CBASE_LOW 0x63 /* SIO KBC command base addr, 7:0 */
/* the logical devices*/
#define LDEV_KBC1 0x00 /* 2 devices for keyboard and mouse controller*/
#define LDEV_KBC2 0x01
#define LDEV_MOUSE 0x01
#define LDEV_RTC_APC 0x02 /*Real Time Clock and Advanced Power Control*/
#define LDEV_FDC 0x03 /*floppy disk controller*/
#define LDEV_PARP 0x04 /*Parallel port*/
#define LDEV_UART2 0x05
#define LDEV_UART1 0x06
#define LDEV_GPIO 0x07 /*General Purpose IO and chip select output signals*/
#define LDEV_POWRMAN 0x08 /*Power Managment*/
#define CONFIG_SYS_NS87308_KBC1 (1 << LDEV_KBC1)
#define CONFIG_SYS_NS87308_KBC2 (1 << LDEV_KBC2)
#define CONFIG_SYS_NS87308_MOUSE (1 << LDEV_MOUSE)
#define CONFIG_SYS_NS87308_RTC_APC (1 << LDEV_RTC_APC)
#define CONFIG_SYS_NS87308_FDC (1 << LDEV_FDC)
#define CONFIG_SYS_NS87308_PARP (1 << LDEV_PARP)
#define CONFIG_SYS_NS87308_UART2 (1 << LDEV_UART2)
#define CONFIG_SYS_NS87308_UART1 (1 << LDEV_UART1)
#define CONFIG_SYS_NS87308_GPIO (1 << LDEV_GPIO)
#define CONFIG_SYS_NS87308_POWRMAN (1 << LDEV_POWRMAN)
/*some functions and macro's for doing configuration */
static inline void read_pnp_config(unsigned char index, unsigned char *data)
{
pci_writeb(index,IO_INDEX);
pci_readb(IO_DATA, *data);
}
static inline void write_pnp_config(unsigned char index, unsigned char data)
{
pci_writeb(index,IO_INDEX);
pci_writeb(data, IO_DATA);
}
static inline void pnp_set_device(unsigned char dev)
{
write_pnp_config(LOGICAL_DEVICE, dev);
}
static inline void write_pm_reg(unsigned short base, unsigned char index, unsigned char data)
{
pci_writeb(index, CONFIG_SYS_ISA_IO + base);
eieio();
pci_writeb(data, CONFIG_SYS_ISA_IO + base + 1);
}
/*void write_pnp_config(unsigned char index, unsigned char data);
void pnp_set_device(unsigned char dev);
*/
#define PNP_SET_DEVICE_BASE(dev,base) \
pnp_set_device(dev); \
write_pnp_config(ACTIVATE, ACTIVATE_OFF); \
write_pnp_config(BASE_ADDR_HIGH, ((base) >> 8) & 0xff ); \
write_pnp_config(BASE_ADDR_LOW, (base) &0xff); \
write_pnp_config(ACTIVATE, ACTIVATE_ON);
#define PNP_ACTIVATE_DEVICE(dev) \
pnp_set_device(dev); \
write_pnp_config(ACTIVATE, ACTIVATE_ON);
#define PNP_DEACTIVATE_DEVICE(dev) \
pnp_set_device(dev); \
write_pnp_config(ACTIVATE, ACTIVATE_OFF);
static inline void write_pgcs_config(unsigned char index, unsigned char data)
{
write_pnp_config(PGCS_INDEX, index);
write_pnp_config(PGCS_DATA, data);
}
/* these macrose configure the 3 CS lines
on the sandpoint board these controll NVRAM
CS0 is connected to NVRAMCS
CS1 is connected to NVRAMAS0
CS2 is connected to NVRAMAS1
*/
#define PGCS_CS_ASSERT_ON_WRITE 0x10
#define PGCS_CS_ASSERT_ON_READ 0x20
#define PNP_PGCS_CSLINE_BASE(cs, base) \
write_pgcs_config((cs) << 2, ((base) >> 8) & 0xff ); \
write_pgcs_config(((cs) << 2) + 1, (base) & 0xff );
#define PNP_PGCS_CSLINE_CONF(cs, conf) \
write_pgcs_config(((cs) << 2) + 2, (conf) );
/* The following sections are for 87308 extensions to the standard compoents it emulates */
/* extensions to 16550*/
#define MCR_MDSL_MSK 0xe0 /*mode select mask*/
#define MCR_MDSL_UART 0x00 /*uart, default*/
#define MCR_MDSL_SHRPIR 0x02 /*Sharp IR*/
#define MCR_MDSL_SIR 0x03 /*SIR*/
#define MCR_MDSL_CIR 0x06 /*Consumer IR*/
#define FCR_TXFTH0 0x10 /* these bits control threshod of data level in fifo */
#define FCR_TXFTH1 0x20 /* for interrupt trigger */
/*
* Default NS87308 configuration
*/
#ifndef CONFIG_SYS_NS87308_KBC1_BASE
#define CONFIG_SYS_NS87308_KBC1_BASE 0x0060
#endif
#ifndef CONFIG_SYS_NS87308_RTC_BASE
#define CONFIG_SYS_NS87308_RTC_BASE 0x0070
#endif
#ifndef CONFIG_SYS_NS87308_FDC_BASE
#define CONFIG_SYS_NS87308_FDC_BASE 0x03F0
#endif
#ifndef CONFIG_SYS_NS87308_LPT_BASE
#define CONFIG_SYS_NS87308_LPT_BASE 0x0278
#endif
#ifndef CONFIG_SYS_NS87308_UART1_BASE
#define CONFIG_SYS_NS87308_UART1_BASE 0x03F8
#endif
#ifndef CONFIG_SYS_NS87308_UART2_BASE
#define CONFIG_SYS_NS87308_UART2_BASE 0x02F8
#endif
#endif /*_NS87308_H_*/