u-boot/board/Arcturus/ucp1020/tlb.c
Oleksandr G Zhadan 8b0044ff59 powerpc/mpc85xx: Add board support for ucp1020
New QorIQ p1020 based board support from Arcturus Networks Inc.
http://www.arcturusnetworks.com/products/ucp1020/

Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
[York Sun: remove patman tags from commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-05-04 09:26:26 -07:00

102 lines
3.3 KiB
C

/*
* Copyright 2013-2015 Arcturus Networks, Inc
* http://www.arcturusnetworks.com/products/ucp1020/
* based on board/freescale/p1_p2_rdb_pc/tlb.c
* original copyright follows:
* Copyright 2010-2011 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/mmu.h>
struct fsl_e_tlb_entry tlb_table[] = {
/* TLB 0 - for temp stack in cache */
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
CONFIG_SYS_INIT_RAM_ADDR_PHYS,
MAS3_SX | MAS3_SW | MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
MAS3_SX | MAS3_SW | MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
MAS3_SX | MAS3_SW | MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
MAS3_SX | MAS3_SW | MAS3_SR, 0,
0, 0, BOOKE_PAGESZ_4K, 0),
/* TLB 1 */
/* *I*** - Covers boot page */
SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I,
0, 0, BOOKE_PAGESZ_4K, 1),
/* *I*G* - CCSRBAR */
SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 1, BOOKE_PAGESZ_1M, 1),
#ifndef CONFIG_SPL_BUILD
/* W**G* - Flash/promjet, localbus */
/* This will be changed to *I*G* after relocation to RAM. */
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
MAS3_SX | MAS3_SR, MAS2_W | MAS2_G,
0, 2, BOOKE_PAGESZ_64M, 1),
#ifdef CONFIG_PCI
/* *I*G* - PCI memory 1.5G */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 3, BOOKE_PAGESZ_1G, 1),
/* *I*G* - PCI I/O effective: 192K */
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 4, BOOKE_PAGESZ_256K, 1),
#endif
#ifdef CONFIG_VSC7385_ENET
/* *I*G - VSC7385 Switch */
SET_TLB_ENTRY(1, CONFIG_SYS_VSC7385_BASE, CONFIG_SYS_VSC7385_BASE_PHYS,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 5, BOOKE_PAGESZ_1M, 1),
#endif
#endif /* not SPL */
#ifdef CONFIG_SYS_NAND_BASE
/* *I*G - NAND */
SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 7, BOOKE_PAGESZ_1M, 1),
#endif
#if defined(CONFIG_SYS_RAMBOOT) || \
(defined(CONFIG_SPL) && !defined(CONFIG_SPL_COMMON_INIT_DDR))
/* *I*G - eSDHC/eSPI/NAND boot */
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
MAS3_SX | MAS3_SW | MAS3_SR, 0,
0, 8, BOOKE_PAGESZ_1G, 1),
#endif /* RAMBOOT/SPL */
#ifdef CONFIG_SYS_INIT_L2_ADDR
/* *I*G - L2SRAM */
SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR, CONFIG_SYS_INIT_L2_ADDR_PHYS,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_G,
0, 11, BOOKE_PAGESZ_256K, 1),
#if CONFIG_SYS_L2_SIZE >= (256 << 10)
SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L2_ADDR + 0x40000,
CONFIG_SYS_INIT_L2_ADDR_PHYS + 0x40000,
MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
0, 12, BOOKE_PAGESZ_256K, 1)
#endif
#endif
};
int num_tlb_entries = ARRAY_SIZE(tlb_table);