u-boot/include/configs/actux1.h
Ladislav Michl 488f5d8790 Remove nowhere used symbol CONFIG_SYS_CLKS_IN_HZ
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2009-03-29 16:04:51 +02:00

246 lines
7.5 KiB
C

/*
* (C) Copyright 2007
* Michael Schwingen, michael@schwingen.org
*
* Configuration settings for the AcTux-1 board.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* 1: modified board with 32MB DRAM */
#define CONFIG_ACTUX1_32MB 0
/* 1: 2*2MB FLASH (standard) */
#define CONFIG_ACTUX1_FLASH2X2 1
/* 1: 1*8MB FLASH (upgraded boards) */
#define CONFIG_ACTUX1_FLASH1X8 0
#define CONFIG_IXP425 1
#define CONFIG_ACTUX1 1
#define CONFIG_DISPLAY_CPUINFO 1
#define CONFIG_DISPLAY_BOARDINFO 1
#define CONFIG_IXP_SERIAL
#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART2
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
/***************************************************************
* U-boot generic defines start here.
***************************************************************/
#undef CONFIG_USE_IRQ
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
/* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_SIZE 128
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
/* Command line configuration. */
#include <config_cmd_default.h>
#define CONFIG_CMD_ELF
#undef CONFIG_CMD_PCI
#undef CONFIG_PCI
#define CONFIG_BOOTCOMMAND "run boot_flash"
/* enable passing of ATAGs */
#define CONFIG_CMDLINE_TAG 1
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG 1
#define CONFIG_REVISION_TAG 1
#if defined(CONFIG_CMD_KGDB)
# define CONFIG_KGDB_BAUDRATE 230400
/* which serial port to use */
# define CONFIG_KGDB_SER_INDEX 1
#endif
/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_PROMPT "=> "
/* Console I/O Buffer Size */
#define CONFIG_SYS_CBSIZE 256
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
/* max number of command args */
#define CONFIG_SYS_MAXARGS 16
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x00800000
/* spec says 66.666 MHz, but it appears to be 33 */
#define CONFIG_SYS_HZ 3333333
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0x00010000
/* valid baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
115200, 230400 }
#define CONFIG_SERIAL_RTS_ACTIVE 1
/*
* Stack sizes
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
#ifdef CONFIG_USE_IRQ
# define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
# define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
#endif
/* Expansion bus settings */
#define CONFIG_SYS_EXP_CS0 0xbd113842
/* SDRAM settings */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x00000000
#define CONFIG_SYS_DRAM_BASE 0x00000000
#if CONFIG_ACTUX1_32MB
# define CONFIG_SYS_SDR_CONFIG 0x18
# define PHYS_SDRAM_1_SIZE 0x02000000
# define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a
# define CONFIG_SYS_SDR_MODE_CONFIG 0x1
# define CONFIG_SYS_DRAM_SIZE 0x02000000
#else /* 16MB SDRAM */
# define CONFIG_SYS_SDR_CONFIG 0x3A
# define PHYS_SDRAM_1_SIZE 0x01000000
# define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a
# define CONFIG_SYS_SDR_MODE_CONFIG 0x1
# define CONFIG_SYS_DRAM_SIZE 0x01000000
#endif
/* FLASH organization */
#if CONFIG_ACTUX1_FLASH2X2
# define CONFIG_SYS_MAX_FLASH_BANKS 2
/* max number of sectors on one chip */
# define CONFIG_SYS_MAX_FLASH_SECT 40
# define PHYS_FLASH_1 0x50000000
# define PHYS_FLASH_2 0x50200000
# define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 }
#endif
#if CONFIG_ACTUX1_FLASH1X8
# define CONFIG_SYS_MAX_FLASH_BANKS 1
/* max number of sectors on one chip */
# define CONFIG_SYS_MAX_FLASH_SECT 140
# define PHYS_FLASH_1 0x50000000
# define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 }
#endif
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
/* Use common CFI driver */
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
/* no byte writes on IXP4xx */
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
/* print 'E' for empty sector on flinfo */
#define CONFIG_SYS_FLASH_EMPTY_INFO
/* Ethernet */
/* include IXP4xx NPE support */
#define CONFIG_IXP4XX_NPE 1
#define CONFIG_NET_MULTI 1
/* NPE0 PHY address */
#define CONFIG_PHY_ADDR 0
/* MII PHY management */
#define CONFIG_MII 1
/* Number of ethernet rx buffers & descriptors */
#define CONFIG_SYS_RX_ETH_BUFFER 16
#define CONFIG_RESET_PHY_R 1
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_NET
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#undef CONFIG_CMD_NFS
/* BOOTP options */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/* Cache Configuration */
#define CONFIG_SYS_CACHELINE_SIZE 32
/*
* environment organization:
* one flash sector, embedded in uboot area (bottom bootblock flash)
*/
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000)
#define CONFIG_SYS_USE_PPCENV 1
#define CONFIG_EXTRA_ENV_SETTINGS \
"npe_ucode=50040000\0" \
"mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \
"kerneladdr=50050000\0" \
"rootaddr=50170000\0" \
"loadaddr=10000\0" \
"updateboot_ser=mw.b 10000 ff 40000;" \
" loady ${loadaddr};" \
" run eraseboot writeboot\0" \
"updateboot_net=mw.b 10000 ff 40000;" \
" tftp ${loadaddr} u-boot.bin;" \
" run eraseboot writeboot\0" \
"eraseboot=protect off 50000000 50003fff;" \
" protect off 50006000 5003ffff;" \
" erase 50000000 50003fff;" \
" erase 50006000 5003ffff\0" \
"writeboot=cp.b 10000 50000000 4000;" \
" cp.b 16000 50006000 3a000\0" \
"eraseenv=protect off 50004000 50005fff;" \
" erase 50004000 50005fff\0" \
"updateroot=tftp ${loadaddr} ${rootfile};" \
" era ${rootaddr} +${filesize};" \
" cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \
"updatekern=tftp ${loadaddr} ${kernelfile};" \
" era ${kerneladdr} +${filesize};" \
" cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \
"flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \
" rootfstype=squashfs,jffs2 init=/etc/preinit\0" \
"netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \
" rootfstype=squashfs,jffs2 init=/etc/preinit\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \
"addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \
"boot_flash=run flashargs addtty addeth;" \
" bootm ${kerneladdr}\0" \
"boot_net=run netargs addtty addeth;" \
" tftpboot ${loadaddr} ${kernelfile};" \
" bootm\0"
#endif /* __CONFIG_H */