u-boot/include/configs/ids8313.h
Joe Hershberger ef0f2f5752 Move defaults from config_cmd_default.h to Kconfig
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25 22:18:34 -04:00

574 lines
16 KiB
C

/*
* (C) Copyright 2013
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* Based on:
* Copyright (c) 2011 IDS GmbH, Germany
* Sergej Stepanov <ste@ids.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_MPC831x
#define CONFIG_MPC8313
#define CONFIG_IDS8313
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_FSL_ELBC
#define CONFIG_MISC_INIT_R
#define CONFIG_BOOT_RETRY_TIME 900
#define CONFIG_BOOT_RETRY_MIN 30
#define CONFIG_BOOTDELAY 1
#define CONFIG_RESET_TO_RETRY
#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
#define CONFIG_SYS_IMMR 0xF0000000
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
/*
* Hardware Reset Configuration Word
* if CLKIN is 66.000MHz, then
* CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz
*/
#define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\
HRCWL_DDR_TO_SCB_CLK_2X1 |\
HRCWL_CSB_TO_CLKIN_2X1 |\
HRCWL_CORE_TO_CSB_2X1)
#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST |\
HRCWH_CORE_ENABLE |\
HRCWH_FROM_0XFFF00100 |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_8BIT |\
HRCWH_RL_EXT_LEGACY |\
HRCWH_TSEC1M_IN_MII |\
HRCWH_TSEC2M_IN_MII |\
HRCWH_BIG_ENDIAN)
#define CONFIG_SYS_SICRH 0x00000000
#define CONFIG_SYS_SICRL (SICRL_LBC | SICRL_SPI_D)
#define CONFIG_HWCONFIG
#define CONFIG_SYS_HID0_INIT 0x000000000
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK |\
HID0_ENABLE_INSTRUCTION_CACHE |\
HID0_DISABLE_DYNAMIC_POWER_MANAGMENT)
#define CONFIG_SYS_HID2 (HID2_HBE | 0x00020000)
/*
* Definitions for initial stack pointer and data area (in DCACHE )
*/
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in DPRAM */
#define CONFIG_SYS_GBL_DATA_SIZE 0x100
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
- CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* Local Bus LCRR and LBCR regs
*/
#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR (0x00040000 |\
(0xFF << LBCR_BMT_SHIFT) |\
0xF)
#define CONFIG_SYS_LBC_MRTPR 0x20000000
/*
* Internal Definitions
*/
/*
* DDR Setup
*/
#define CONFIG_SYS_DDR_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
/*
* Manually set up DDR parameters,
* as this board has not the SPD connected to I2C.
*/
#define CONFIG_SYS_DDR_SIZE 256 /* MB */
#define CONFIG_SYS_DDR_CONFIG (CSCONFIG_EN |\
0x00010000 |\
CSCONFIG_ROW_BIT_13 |\
CSCONFIG_COL_BIT_10)
#define CONFIG_SYS_DDR_CONFIG_256 (CONFIG_SYS_DDR_CONFIG | \
CSCONFIG_BANK_BIT_3)
#define CONFIG_SYS_DDR_TIMING_3 (1 << 16) /* ext refrec */
#define CONFIG_SYS_DDR_TIMING_0 ((3 << TIMING_CFG0_RWT_SHIFT) |\
(3 << TIMING_CFG0_WRT_SHIFT) |\
(3 << TIMING_CFG0_RRT_SHIFT) |\
(3 << TIMING_CFG0_WWT_SHIFT) |\
(6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\
(2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\
(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
(2 << TIMING_CFG0_MRS_CYC_SHIFT))
#define CONFIG_SYS_DDR_TIMING_1 ((4 << TIMING_CFG1_PRETOACT_SHIFT) |\
(12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\
(4 << TIMING_CFG1_ACTTORW_SHIFT) |\
(7 << TIMING_CFG1_CASLAT_SHIFT) |\
(4 << TIMING_CFG1_REFREC_SHIFT) |\
(4 << TIMING_CFG1_WRREC_SHIFT) |\
(2 << TIMING_CFG1_ACTTOACT_SHIFT) |\
(2 << TIMING_CFG1_WRTORD_SHIFT))
#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\
(5 << TIMING_CFG2_CPO_SHIFT) |\
(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\
(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\
(0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\
(1 << TIMING_CFG2_CKE_PLS_SHIFT) |\
(6 << TIMING_CFG2_FOUR_ACT_SHIFT))
#define CONFIG_SYS_DDR_INTERVAL ((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\
(0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN |\
SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\
SDRAM_CFG_DBW_32 |\
SDRAM_CFG_SDRAM_TYPE_DDR2)
#define CONFIG_SYS_SDRAM_CFG2 0x00401000
#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) |\
(0x0242 << SDRAM_MODE_SD_SHIFT))
#define CONFIG_SYS_DDR_MODE_2 0x00000000
#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN |\
DDRCDR_PZ_NOMZ |\
DDRCDR_NZ_NOMZ |\
DDRCDR_ODT |\
DDRCDR_M_ODR |\
DDRCDR_Q_DRN)
/*
* on-board devices
*/
#define CONFIG_TSEC1
#define CONFIG_TSEC2
#define CONFIG_TSEC_ENET
#define CONFIG_HARD_SPI
#define CONFIG_HARD_I2C
/*
* NOR FLASH setup
*/
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
#define CONFIG_FLASH_SHOW_PROGRESS 50
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_BASE 0xFF800000
#define CONFIG_SYS_FLASH_SIZE 8
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\
BR_PS_8 |\
BR_MS_GPCM |\
BR_V)
#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
OR_GPCM_SCY_10 |\
OR_GPCM_EHTR |\
OR_GPCM_TRLX |\
OR_GPCM_CSNT |\
OR_GPCM_EAD)
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 128
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000
#define CONFIG_SYS_FLASH_WRITE_TOUT 500
/*
* NAND FLASH setup
*/
#define CONFIG_SYS_NAND_BASE 0xE1000000
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_MAX_CHIPS 1
#define CONFIG_NAND_FSL_ELBC
#define CONFIG_SYS_NAND_PAGE_SIZE (2048)
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
#define NAND_CACHE_PAGES 64
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E
#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_NAND_BASE) |\
(2<<BR_DECC_SHIFT) |\
BR_PS_8 |\
BR_MS_FCM |\
BR_V)
#define CONFIG_SYS_OR1_PRELIM (0xFFFF8000 |\
OR_FCM_PGS |\
OR_FCM_CSCT |\
OR_FCM_CST |\
OR_FCM_CHT |\
OR_FCM_SCY_4 |\
OR_FCM_TRLX |\
OR_FCM_EHTR |\
OR_FCM_RST)
/*
* MRAM setup
*/
#define CONFIG_SYS_MRAM_BASE 0xE2000000
#define CONFIG_SYS_MRAM_SIZE 0x20000 /* 128 Kb */
#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_MRAM_BASE
#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* 128 Kb */
#define CONFIG_SYS_OR_TIMING_MRAM
#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_MRAM_BASE |\
BR_PS_8 |\
BR_MS_GPCM |\
BR_V)
#define CONFIG_SYS_OR2_PRELIM 0xFFFE0C74
/*
* CPLD setup
*/
#define CONFIG_SYS_CPLD_BASE 0xE3000000
#define CONFIG_SYS_CPLD_SIZE 0x8000
#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_CPLD_BASE
#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E
#define CONFIG_SYS_OR_TIMING_MRAM
#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_CPLD_BASE |\
BR_PS_8 |\
BR_MS_GPCM |\
BR_V)
#define CONFIG_SYS_OR3_PRELIM 0xFFFF8814
/*
* HW-Watchdog
*/
#define CONFIG_WATCHDOG 1
#define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF
/*
* I2C setup
*/
#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100
#define CONFIG_RTC_PCF8563
#define CONFIG_SYS_I2C_RTC_ADDR 0x51
/*
* SPI setup
*/
#ifdef CONFIG_HARD_SPI
#define CONFIG_MPC8XXX_SPI
#define CONFIG_CMD_SPI
#define CONFIG_SYS_GPIO1_PRELIM
#define CONFIG_SYS_GPIO1_DIR 0x00000001
#define CONFIG_SYS_GPIO1_DAT 0x00000001
#endif
/*
* Ethernet setup
*/
#ifdef CONFIG_TSEC1
#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define TSEC1_PHY_ADDR 0x1
#define TSEC1_FLAGS TSEC_GIGABIT
#define TSEC1_PHYIDX 0
#endif
#ifdef CONFIG_TSEC2
#define CONFIG_HAS_ETH1
#define CONFIG_TSEC2_NAME "TSEC1"
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define TSEC2_PHY_ADDR 0x3
#define TSEC2_FLAGS TSEC_GIGABIT
#define TSEC2_PHYIDX 0
#endif
#define CONFIG_ETHPRIME "TSEC1"
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2)
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_SYS_SCCR_USBDRCM 3
/*
* BAT's
*/
#define CONFIG_HIGH_BATS
/* DDR @ 0x00000000 */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE |\
BATL_PP_10)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE |\
BATU_BL_256M |\
BATU_VS |\
BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* Initial RAM @ 0xFD000000 */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR |\
BATL_PP_10 |\
BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR |\
BATU_BL_256K |\
BATU_VS |\
BATU_VP)
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* FLASH @ 0xFF800000 */
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE |\
BATL_PP_10 |\
BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE |\
BATU_BL_8M |\
BATU_VS |\
BATU_VP)
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE |\
BATL_PP_10 |\
BATL_CACHEINHIBIT |\
BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
#define CONFIG_SYS_IBAT3L (0)
#define CONFIG_SYS_IBAT3U (0)
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
#define CONFIG_SYS_IBAT4L (0)
#define CONFIG_SYS_IBAT4U (0)
#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
/* IMMRBAR @ 0xF0000000 */
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR |\
BATL_PP_10 |\
BATL_CACHEINHIBIT |\
BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR |\
BATU_BL_128M |\
BATU_VS |\
BATU_VP)
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
/* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */
#define CONFIG_SYS_IBAT6L (0xE0000000 |\
BATL_PP_10 |\
BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xE0000000 |\
BATU_BL_256M |\
BATU_VS |\
BATU_VP)
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
#define CONFIG_SYS_IBAT7L (0)
#define CONFIG_SYS_IBAT7U (0)
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
/*
* U-Boot environment setup
*/
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
#define CONFIG_CMD_NAND
#define CONFIG_CMD_SNTP
#define CONFIG_CMD_MII
#define CONFIG_CMD_DATE
#define CONFIG_CMDLINE_EDITING
#define CONFIG_CMD_JFFS2
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS
/*
* The reserved memory
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (8 * 1024 * 1024)
/*
* Environment Configuration
*/
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \
+ CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SIZE 0x20000
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#define CONFIG_NETDEV eth1
#define CONFIG_HOSTNAME ids8313
#define CONFIG_ROOTPATH "/opt/eldk-4.2/ppc_6xx"
#define CONFIG_BOOTFILE "ids8313/uImage"
#define CONFIG_UBOOTPATH "ids8313/u-boot.bin"
#define CONFIG_FDTFILE "ids8313/ids8313.dtb"
#define CONFIG_LOADADDR 0x400000
#define CONFIG_CMD_ENV_FLAGS
#define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
#define CONFIG_BAUDRATE 115200
/* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_CBSIZE 1024
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_MEMTEST_START 0x00001000
#define CONFIG_SYS_MEMTEST_END 0x00C00000
#define CONFIG_SYS_LOAD_ADDR 0x100000
#define CONFIG_MII
#define CONFIG_LOADS_ECHO
#define CONFIG_TIMESTAMP
#define CONFIG_PREBOOT "echo;" \
"echo Type \\\"run nfsboot\\\" " \
"to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND "run boot_cramfs"
#undef CONFIG_SYS_LOADS_BAUD_CHANGE
#define CONFIG_JFFS2_NAND
#define CONFIG_JFFS2_DEV "0"
/* mtdparts command line support */
#define CONFIG_CMD_MTDPARTS
#define CONFIG_FLASH_CFI_MTD
#define CONFIG_MTD_DEVICE
#define MTDIDS_DEFAULT "nor0=ff800000.flash,nand0=e1000000.flash"
#define MTDPARTS_DEFAULT "mtdparts=ff800000.flash:7m(dum)," \
"768k(BOOT-BIN)," \
"128k(BOOT-ENV),128k(BOOT-REDENV);" \
"e1000000.flash:-(ubi)"
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=" __stringify(CONFIG_NETDEV) "\0" \
"ethprime=TSEC1\0" \
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
"tftpflash=tftpboot ${loadaddr} ${uboot}; " \
"protect off " __stringify(CONFIG_SYS_TEXT_BASE) \
" +${filesize}; " \
"erase " __stringify(CONFIG_SYS_TEXT_BASE) \
" +${filesize}; " \
"cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \
" ${filesize}; " \
"protect on " __stringify(CONFIG_SYS_TEXT_BASE) \
" +${filesize}; " \
"cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE) \
" ${filesize}\0" \
"console=ttyS0\0" \
"fdtaddr=0x780000\0" \
"kernel_addr=ff800000\0" \
"fdtfile=" __stringify(CONFIG_FDTFILE) "\0" \
"setbootargs=setenv bootargs " \
"root=${rootdev} rw console=${console}," \
"${baudrate} ${othbootargs}\0" \
"setipargs=setenv bootargs root=${rootdev} rw " \
"nfsroot=${serverip}:${rootpath} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:" \
"${netmask}:${hostname}:${netdev}:off " \
"console=${console},${baudrate} ${othbootargs}\0" \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
"mtdids=" MTDIDS_DEFAULT "\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
"\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv rootdev /dev/nfs;" \
"run setipargs;run addmtd;" \
"tftp ${loadaddr} ${bootfile};" \
"tftp ${fdtaddr} ${fdtfile};" \
"fdt addr ${fdtaddr};" \
"bootm ${loadaddr} - ${fdtaddr}"
/* UBI Support */
#define CONFIG_CMD_NAND_TRIMFFS
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_RBTREE
#define CONFIG_LZO
#define CONFIG_MTD_PARTITIONS
/* bootcount support */
#define CONFIG_BOOTCOUNT_LIMIT
#define CONFIG_BOOTCOUNT_I2C
#define CONFIG_BOOTCOUNT_ALEN 1
#define CONFIG_SYS_BOOTCOUNT_ADDR 0x9
#define CONFIG_VERSION_VARIABLE
#define CONFIG_IMAGE_FORMAT_LEGACY
#define CONFIG_CMD_FDT
#define CONFIG_CMD_HASH
#define CONFIG_SHA1
#define CONFIG_SHA256
#endif /* __CONFIG_H */