GPMC controller needs to be configured based on bus-width of the NAND device connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI parameters is not possible in following situations: SPL: SPL NAND drivers does not support ONFI parameter reading. U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init() which is called before probing for devices, hence any ONFI parameter information is not available during GPMC initialization. Thus, OMAP NAND driver expected board developers to explicitely write GPMC configurations specific to NAND device attached on board in board files itself. But this was troublesome for board manufacturers as they need to dive into lengthy platform & SoC documents to find details of GPMC registers and appropriate configurations to get NAND device working. This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config hich indicates that connected NAND device has x16 bus-width. And then based on this config GPMC driver itself initializes itself based on NAND bus-width. This keeps board developers free from knowing GPMC controller specific internals. Signed-off-by: Pekon Gupta <pekon@ti.com>
358 lines
11 KiB
C
358 lines
11 KiB
C
/*
|
|
* (C) Copyright 2006-2008
|
|
* Texas Instruments.
|
|
* Richard Woodruff <r-woodruff2@ti.com>
|
|
* Syed Mohammed Khasim <x0khasim@ti.com>
|
|
*
|
|
* (C) Copyright 2009
|
|
* Frederik Kriewitz <frederik@kriewitz.eu>
|
|
*
|
|
* Configuration settings for the DevKit8000 board.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/* High Level Configuration Options */
|
|
#define CONFIG_OMAP 1 /* in a TI OMAP core */
|
|
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
|
|
#define CONFIG_OMAP3_DEVKIT8000 1 /* working with DevKit8000 */
|
|
#define CONFIG_MACH_TYPE MACH_TYPE_DEVKIT8000
|
|
#define CONFIG_OMAP_GPIO
|
|
#define CONFIG_OMAP_COMMON
|
|
|
|
/*
|
|
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
|
|
* 64 bytes before this address should be set aside for u-boot.img's
|
|
* header. That is 0x800FFFC0--0x80100000 should not be used for any
|
|
* other needs.
|
|
*/
|
|
#define CONFIG_SYS_TEXT_BASE 0x80100000
|
|
|
|
#define CONFIG_SDRC /* The chip has SDRC controller */
|
|
|
|
#include <asm/arch/cpu.h> /* get chip and board defs */
|
|
#include <asm/arch/omap3.h>
|
|
|
|
/* Display CPU and Board information */
|
|
#define CONFIG_DISPLAY_CPUINFO 1
|
|
#define CONFIG_DISPLAY_BOARDINFO 1
|
|
|
|
/* Clock Defines */
|
|
#define V_OSCK 26000000 /* Clock output from T2 */
|
|
#define V_SCLK (V_OSCK >> 1)
|
|
|
|
#define CONFIG_MISC_INIT_R
|
|
|
|
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
|
|
#define CONFIG_SETUP_MEMORY_TAGS 1
|
|
#define CONFIG_INITRD_TAG 1
|
|
#define CONFIG_REVISION_TAG 1
|
|
|
|
#define CONFIG_OF_LIBFDT 1
|
|
|
|
/* Size of malloc() pool */
|
|
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
|
|
/* Sector */
|
|
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
|
|
|
|
/* Hardware drivers */
|
|
/* DM9000 */
|
|
#define CONFIG_NET_RETRY_COUNT 20
|
|
#define CONFIG_DRIVER_DM9000 1
|
|
#define CONFIG_DM9000_BASE 0x2c000000
|
|
#define DM9000_IO CONFIG_DM9000_BASE
|
|
#define DM9000_DATA (CONFIG_DM9000_BASE + 0x400)
|
|
#define CONFIG_DM9000_USE_16BIT 1
|
|
#define CONFIG_DM9000_NO_SROM 1
|
|
#undef CONFIG_DM9000_DEBUG
|
|
|
|
/* NS16550 Configuration */
|
|
#define CONFIG_SYS_NS16550
|
|
#define CONFIG_SYS_NS16550_SERIAL
|
|
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
|
|
#define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
|
|
|
|
/* select serial console configuration */
|
|
#define CONFIG_CONS_INDEX 3
|
|
#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
|
|
#define CONFIG_SERIAL3 3
|
|
#define CONFIG_BAUDRATE 115200
|
|
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
|
|
115200}
|
|
|
|
/* MMC */
|
|
#define CONFIG_GENERIC_MMC 1
|
|
#define CONFIG_MMC 1
|
|
#define CONFIG_OMAP_HSMMC 1
|
|
#define CONFIG_DOS_PARTITION 1
|
|
|
|
/* I2C */
|
|
#define CONFIG_SYS_I2C
|
|
#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
|
|
#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
|
|
#define CONFIG_SYS_I2C_OMAP34XX
|
|
|
|
/* TWL4030 */
|
|
#define CONFIG_TWL4030_POWER 1
|
|
#define CONFIG_TWL4030_LED 1
|
|
|
|
/* Board NAND Info */
|
|
#define CONFIG_SYS_NO_FLASH /* no NOR flash */
|
|
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
|
|
#define MTDIDS_DEFAULT "nand0=nand"
|
|
#define MTDPARTS_DEFAULT "mtdparts=nand:" \
|
|
"512k(x-loader)," \
|
|
"1920k(u-boot)," \
|
|
"128k(u-boot-env)," \
|
|
"4m(kernel)," \
|
|
"-(fs)"
|
|
|
|
#define CONFIG_NAND_OMAP_GPMC
|
|
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
|
|
/* to access nand */
|
|
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
|
|
/* to access nand at */
|
|
/* CS0 */
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
|
|
/* devices */
|
|
#define CONFIG_JFFS2_NAND
|
|
/* nand device jffs2 lives on */
|
|
#define CONFIG_JFFS2_DEV "nand0"
|
|
/* start of jffs2 partition */
|
|
#define CONFIG_JFFS2_PART_OFFSET 0x680000
|
|
#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */
|
|
/* partition */
|
|
|
|
/* commands to include */
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_DHCP /* DHCP support */
|
|
#define CONFIG_CMD_EXT2 /* EXT2 Support */
|
|
#define CONFIG_CMD_FAT /* FAT support */
|
|
#define CONFIG_CMD_I2C /* I2C serial bus support */
|
|
#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
|
|
#define CONFIG_CMD_MMC /* MMC support */
|
|
#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
|
|
#define CONFIG_CMD_NAND /* NAND support */
|
|
#define CONFIG_CMD_NAND_LOCK_UNLOCK /* nand (un)lock commands */
|
|
|
|
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
|
|
#undef CONFIG_CMD_IMI /* iminfo */
|
|
|
|
/* BOOTP/DHCP options */
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
#define CONFIG_BOOTP_NISDOMAIN
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_DNS
|
|
#define CONFIG_BOOTP_DNS2
|
|
#define CONFIG_BOOTP_SEND_HOSTNAME
|
|
#define CONFIG_BOOTP_NTPSERVER
|
|
#define CONFIG_BOOTP_TIMEOFFSET
|
|
#undef CONFIG_BOOTP_VENDOREX
|
|
|
|
/* Environment information */
|
|
#define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */
|
|
|
|
#define CONFIG_BOOTDELAY 3
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"loadaddr=0x82000000\0" \
|
|
"console=ttyO2,115200n8\0" \
|
|
"mmcdev=0\0" \
|
|
"vram=12M\0" \
|
|
"dvimode=1024x768MR-16@60\0" \
|
|
"defaultdisplay=dvi\0" \
|
|
"nfsopts=hard,tcp,rsize=65536,wsize=65536\0" \
|
|
"kernelopts=rw\0" \
|
|
"commonargs=" \
|
|
"setenv bootargs console=${console} " \
|
|
"vram=${vram} " \
|
|
"omapfb.mode=dvi:${dvimode} " \
|
|
"omapdss.def_disp=${defaultdisplay}\0" \
|
|
"mmcargs=" \
|
|
"run commonargs; " \
|
|
"setenv bootargs ${bootargs} " \
|
|
"root=/dev/mmcblk0p2 " \
|
|
"rootwait " \
|
|
"${kernelopts}\0" \
|
|
"nandargs=" \
|
|
"run commonargs; " \
|
|
"setenv bootargs ${bootargs} " \
|
|
"omapfb.mode=dvi:${dvimode} " \
|
|
"omapdss.def_disp=${defaultdisplay} " \
|
|
"root=/dev/mtdblock4 " \
|
|
"rootfstype=jffs2 " \
|
|
"${kernelopts}\0" \
|
|
"netargs=" \
|
|
"run commonargs; " \
|
|
"setenv bootargs ${bootargs} " \
|
|
"root=/dev/nfs " \
|
|
"nfsroot=${serverip}:${rootpath},${nfsopts} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off " \
|
|
"${kernelopts} " \
|
|
"dnsip1=${dnsip} " \
|
|
"dnsip2=${dnsip2}\0" \
|
|
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
|
|
"bootscript=echo Running bootscript from mmc ...; " \
|
|
"source ${loadaddr}\0" \
|
|
"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
|
|
"eraseenv=nand unlock 0x260000 0x20000; nand erase 0x260000 0x20000\0" \
|
|
"mmcboot=echo Booting from mmc ...; " \
|
|
"run mmcargs; " \
|
|
"bootm ${loadaddr}\0" \
|
|
"nandboot=echo Booting from nand ...; " \
|
|
"run nandargs; " \
|
|
"nand read ${loadaddr} 280000 400000; " \
|
|
"bootm ${loadaddr}\0" \
|
|
"netboot=echo Booting from network ...; " \
|
|
"dhcp ${loadaddr}; " \
|
|
"run netargs; " \
|
|
"bootm ${loadaddr}\0" \
|
|
"autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \
|
|
"if run loadbootscript; then " \
|
|
"run bootscript; " \
|
|
"else " \
|
|
"if run loaduimage; then " \
|
|
"run mmcboot; " \
|
|
"else run nandboot; " \
|
|
"fi; " \
|
|
"fi; " \
|
|
"else run nandboot; fi\0"
|
|
|
|
|
|
#define CONFIG_BOOTCOMMAND "run autoboot"
|
|
|
|
/* Miscellaneous configurable options */
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
|
|
#define CONFIG_AUTO_COMPLETE 1
|
|
#define CONFIG_SYS_PROMPT "OMAP3 DevKit8000 # "
|
|
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
|
|
/* Print Buffer Size */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
|
|
sizeof(CONFIG_SYS_PROMPT) + 16)
|
|
#define CONFIG_SYS_MAXARGS 128 /* max number of command args */
|
|
|
|
/* Boot Argument Buffer Size */
|
|
#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
|
|
|
|
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x07000000)
|
|
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \
|
|
0x01000000) /* 16MB */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000)
|
|
|
|
/*
|
|
* OMAP3 has 12 GP timers, they can be driven by the system clock
|
|
* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
|
|
* This rate is divided by a local divisor.
|
|
*/
|
|
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
|
|
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
|
|
|
|
/* Physical Memory Map */
|
|
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
|
|
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
|
|
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
|
|
|
|
/* NAND and environment organization */
|
|
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
|
|
|
|
#define CONFIG_ENV_IS_IN_NAND 1
|
|
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
|
|
|
|
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
|
|
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
|
|
CONFIG_SYS_INIT_RAM_SIZE - \
|
|
GENERATED_GBL_DATA_SIZE)
|
|
|
|
/* SRAM config */
|
|
#define CONFIG_SYS_SRAM_START 0x40200000
|
|
#define CONFIG_SYS_SRAM_SIZE 0x10000
|
|
|
|
/* Defines for SPL */
|
|
#define CONFIG_SPL
|
|
#define CONFIG_SPL_FRAMEWORK
|
|
#define CONFIG_SPL_NAND_SIMPLE
|
|
|
|
#define CONFIG_SPL_LIBCOMMON_SUPPORT
|
|
#define CONFIG_SPL_LIBDISK_SUPPORT
|
|
#define CONFIG_SPL_BOARD_INIT
|
|
#define CONFIG_SPL_I2C_SUPPORT
|
|
#define CONFIG_SPL_LIBGENERIC_SUPPORT
|
|
#define CONFIG_SPL_SERIAL_SUPPORT
|
|
#define CONFIG_SPL_GPIO_SUPPORT
|
|
#define CONFIG_SPL_POWER_SUPPORT
|
|
#define CONFIG_SPL_NAND_SUPPORT
|
|
#define CONFIG_SPL_NAND_BASE
|
|
#define CONFIG_SPL_NAND_DRIVERS
|
|
#define CONFIG_SPL_NAND_ECC
|
|
#define CONFIG_SPL_MMC_SUPPORT
|
|
#define CONFIG_SPL_FAT_SUPPORT
|
|
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
|
|
#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
|
|
#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
|
|
|
|
#define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/
|
|
#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
|
|
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
|
|
|
|
#define CONFIG_SPL_BSS_START_ADDR 0x80000500 /* leave space for bootargs*/
|
|
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
|
|
|
|
/* NAND boot config */
|
|
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16
|
|
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
#define CONFIG_SYS_NAND_PAGE_COUNT 64
|
|
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
|
|
#define CONFIG_SYS_NAND_OOBSIZE 64
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
|
|
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
|
|
#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
|
|
10, 11, 12, 13}
|
|
|
|
#define CONFIG_SYS_NAND_ECCSIZE 512
|
|
#define CONFIG_SYS_NAND_ECCBYTES 3
|
|
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
|
|
|
|
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
|
|
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
|
|
#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x200000
|
|
|
|
#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
|
|
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */
|
|
|
|
/* SPL OS boot options */
|
|
#define CONFIG_SPL_OS_BOOT
|
|
|
|
#define CONFIG_CMD_SPL
|
|
#define CONFIG_CMD_SPL_WRITE_SIZE 0x400 /* 1024 byte */
|
|
#define CONFIG_CMD_SPL_NAND_OFS (CONFIG_SYS_NAND_SPL_KERNEL_OFFS+\
|
|
0x400000)
|
|
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
|
|
|
|
#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "uImage"
|
|
#define CONFIG_SPL_FAT_LOAD_ARGS_NAME "args"
|
|
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x500 /* address 0xa0000 */
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x8 /* address 0x1000 */
|
|
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 8 /* 4KB */
|
|
|
|
#define CONFIG_SYS_SPL_ARGS_ADDR (PHYS_SDRAM_1 + 0x100)
|
|
|
|
#endif /* __CONFIG_H */
|