u-boot/include/configs/o2dnt2.h
Anatolij Gustschin 4a8c3f693e Use __stringify() instead of xstr()
Some boards still use xstr(). Replace remaining occurrences
of xstr() by commonly used __stringify().

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2014-10-27 17:54:13 -04:00

70 lines
2.1 KiB
C

/*
* (C) Copyright 2012
* DENX Software Engineering, Anatolij Gustschin <agust@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* Valid values for CONFIG_SYS_TEXT_BASE are:
* 0xFC000000 boot low boot high (standard configuration)
* 0x00100000 boot from RAM (for testing only)
*/
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xfc000000 /* Standard: boot low */
#endif
/* Board specific flash config */
#define CONFIG_SYS_FLASH_BASE 0xfc000000
#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* maximum 64MB */
/* max number of sectors on one chip */
#define CONFIG_SYS_MAX_FLASH_SECT 512
/*
* Include common defines for all ifm boards
*/
#include "o2dnt-common.h"
/* additional commands */
#define CONFIG_CMD_ITEST
/*
* GPIO configuration:
* CS1 SDRAM activate + no CAN + no PCI
*/
#define CONFIG_SYS_GPS_PORT_CONFIG 0x8000A004
/* Other board specific configs */
#define CONFIG_SYS_BOOTCS_CFG 0x00057d01
#define CONFIG_SYS_RESET_ADDRESS 0xfc000000
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x07f00000 /* 1 - 127 MB in DRAM */
#define CONFIG_BOARD_NAME "o2dnt2"
#define CONFIG_BOARD_BOOTCMD "run flash_self"
#define CONFIG_BOARD_MEM_LIMIT __stringify(126)
#define BOARD_POST_CRC32_END __stringify(0x01000000)
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_IFM_DEFAULT_ENV_SETTINGS \
CONFIG_IFM_DEFAULT_ENV_OLD \
CONFIG_IFM_DEFAULT_ENV_NEW \
"linbot=fc060000\0" \
"lintop=fc15ffff\0" \
"rambot=fc160000\0" \
"ramtop=fc55ffff\0" \
"jffbot=fc560000\0" \
"jfftop=fce5ffff\0" \
"ubobot=" __stringify(CONFIG_SYS_FLASH_BASE) "\0" \
"ubotop=fc03ffff\0" \
"calname="CONFIG_BOARD_NAME"/uCal_"CONFIG_BOARD_NAME"_act\0" \
"calbot=fce60000\0" \
"caltop=fcffffff\0" \
"progCal=tftp 200000 ${calname};erase ${calbot} ${caltop};" \
"cp.b ${fileaddr} ${calbot} ${filesize}\0" \
"kernel_addr=0xfc060000\0" \
"ramdisk_addr=0xfc160000\0" \
"master=mw f0000b00 0x8005A006;mw f0000b0c ${IOpin};" \
"mw f0000b04 ${IOpin};mw f0000b10 0x20\0"