u-boot/board/xilinx/common/xipif_v1_23_b.c
wdenk a06752e36b * Patch by Sean Chang, 9 Aug 2004:
- Added I2C support for ML300.
  - Added support for ML300 to read out its environment information
    stored on the EEPROM.
  - Added support to use board specific parameters as part of
    U-Boot's environment information.
  - Updated MLD files to support configuration for new features
    above.

* Patches by Travis Sawyer, 5 Aug 2004:
  - Remove incorrect bridge settings for eth group 6
  - Add call to setup bridge in ppc_440x_eth_initialize
  - Fix ppc_440x_eth_init to reset the phy only if its the
    first time through, otherwise, just check the phy for the
    autonegotiated speed/duplex.  This allows the use of netconsole
  - only print the speed/duplex the first time the phy is reset.
2004-09-29 22:43:59 +00:00

332 lines
14 KiB
C

/* $Id: xipif_v1_23_b.c,v 1.1 2002/03/18 23:24:52 linnj Exp $ */
/******************************************************************************
*
* XILINX IS PROVIDING THIS DESIGN, CODE, OR INFORMATION "AS IS"
* AS A COURTESY TO YOU, SOLELY FOR USE IN DEVELOPING PROGRAMS AND
* SOLUTIONS FOR XILINX DEVICES. BY PROVIDING THIS DESIGN, CODE,
* OR INFORMATION AS ONE POSSIBLE IMPLEMENTATION OF THIS FEATURE,
* APPLICATION OR STANDARD, XILINX IS MAKING NO REPRESENTATION
* THAT THIS IMPLEMENTATION IS FREE FROM ANY CLAIMS OF INFRINGEMENT,
* AND YOU ARE RESPONSIBLE FOR OBTAINING ANY RIGHTS YOU MAY REQUIRE
* FOR YOUR IMPLEMENTATION. XILINX EXPRESSLY DISCLAIMS ANY
* WARRANTY WHATSOEVER WITH RESPECT TO THE ADEQUACY OF THE
* IMPLEMENTATION, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OR
* REPRESENTATIONS THAT THIS IMPLEMENTATION IS FREE FROM CLAIMS OF
* INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE.
*
* (c) Copyright 2002 Xilinx Inc.
* All rights reserved.
*
******************************************************************************/
/******************************************************************************
*
* FILENAME:
*
* xipif.c
*
* DESCRIPTION:
*
* This file contains the implementation of the XIpIf component. The
* XIpIf component encapsulates the IPIF, which is the standard interface
* that IP must adhere to when connecting to a bus. The purpose of this
* component is to encapsulate the IPIF processing such that maintainability
* is increased. This component does not provide a lot of abstraction from
* from the details of the IPIF as it is considered a building block for
* device drivers. A device driver designer must be familiar with the
* details of the IPIF hardware to use this component.
*
* The IPIF hardware provides a building block for all hardware devices such
* that each device does not need to reimplement these building blocks. The
* IPIF contains other building blocks, such as FIFOs and DMA channels, which
* are also common to many devices. These blocks are implemented as separate
* hardware blocks and instantiated within the IPIF. The primary hardware of
* the IPIF which is implemented by this software component is the interrupt
* architecture. Since there are many blocks of a device which may generate
* interrupts, all the interrupt processing is contained in the common part
* of the device, the IPIF. This interrupt processing is for the device level
* only and does not include any processing for the interrupt controller.
*
* A device is a mechanism such as an Ethernet MAC. The device is made
* up of several parts which include an IPIF and the IP. The IPIF contains most
* of the device infrastructure which is common to all devices, such as
* interrupt processing, DMA channels, and FIFOs. The infrastructure may also
* be referred to as IPIF internal blocks since they are part of the IPIF and
* are separate blocks that can be selected based upon the needs of the device.
* The IP of the device is the logic that is unique to the device and interfaces
* to the IPIF of the device.
*
* In general, there are two levels of registers within the IPIF. The first
* level, referred to as the device level, contains registers which are for the
* entire device. The second level, referred to as the IP level, contains
* registers which are specific to the IP of the device. The two levels of
* registers are designed to be hierarchical such that the device level is
* is a more general register set above the more specific registers of the IP.
* The IP level of registers provides functionality which is typically common
* across all devices and allows IP designers to focus on the unique aspects
* of the IP.
*
* The interrupt registers of the IPIF are parameterizable such that the only
* the number of bits necessary for the device are implemented. The functions
* of this component do not attempt to validate that the passed in arguments are
* valid based upon the number of implemented bits. This is necessary to
* maintain the level of performance required for the common components. Bits
* of the registers are assigned starting at the least significant bit of the
* registers.
*
* Critical Sections
*
* It is the responsibility of the device driver designer to use critical
* sections as necessary when calling functions of the IPIF. This component
* does not use critical sections and it does access registers using
* read-modify-write operations. Calls to IPIF functions from a main thread
* and from an interrupt context could produce unpredictable behavior such that
* the caller must provide the appropriate critical sections.
*
* Mutual Exclusion
*
* The functions of the IPIF are not thread safe such that the caller of all
* functions is responsible for ensuring mutual exclusion for an IPIF. Mutual
* exclusion across multiple IPIF components is not necessary.
*
* NOTES:
*
* None.
*
* MODIFICATION HISTORY:
*
* Ver Who Date Changes
* ----- ---- -------- -----------------------------------------------
* 1.23b jhl 02/27/01 Repartioned to reduce size
*
******************************************************************************/
/***************************** Include Files *********************************/
#include "xipif_v1_23_b.h"
#include "xio.h"
/************************** Constant Definitions *****************************/
/* the following constant is used to generate bit masks for register testing
* in the self test functions, it defines the starting bit mask that is to be
* shifted from the LSB to MSB in creating a register test mask
*/
#define XIIF_V123B_FIRST_BIT_MASK 1UL
/**************************** Type Definitions *******************************/
/***************** Macros (Inline Functions) Definitions *********************/
/************************** Variable Definitions *****************************/
/************************** Function Prototypes ******************************/
static XStatus IpIntrSelfTest(u32 RegBaseAddress, u32 IpRegistersWidth);
/******************************************************************************
*
* FUNCTION:
*
* XIpIf_SelfTest
*
* DESCRIPTION:
*
* This function performs a self test on the specified IPIF component. Many
* of the registers in the IPIF are tested to ensure proper operation. This
* function is destructive because the IPIF is reset at the start of the test
* and at the end of the test to ensure predictable results. The IPIF reset
* also resets the entire device that uses the IPIF. This function exits with
* all interrupts for the device disabled.
*
* ARGUMENTS:
*
* InstancePtr points to the XIpIf to operate on.
*
* DeviceRegistersWidth contains the number of bits in the device interrupt
* registers. The hardware is parameterizable such that only the number of bits
* necessary to support a device are implemented. This value must be between 0
* and 32 with 0 indicating there are no device interrupt registers used.
*
* IpRegistersWidth contains the number of bits in the IP interrupt registers
* of the device. The hardware is parameterizable such that only the number of
* bits necessary to support a device are implemented. This value must be
* between 0 and 32 with 0 indicating there are no IP interrupt registers used.
*
* RETURN VALUE:
*
* A value of XST_SUCCESS indicates the test was successful with no errors.
* Any one of the following error values may also be returned.
*
* XST_IPIF_RESET_REGISTER_ERROR The value of a register at reset was
* not valid
* XST_IPIF_IP_STATUS_ERROR A write to the IP interrupt status
* register did not read back correctly
* XST_IPIF_IP_ACK_ERROR One or more bits in the IP interrupt
* status register did not reset when acked
* XST_IPIF_IP_ENABLE_ERROR The IP interrupt enable register
* did not read back correctly based upon
* what was written to it
*
* NOTES:
*
* None.
*
******************************************************************************/
/* the following constant defines the maximum number of bits which may be
* used in the registers at the device and IP levels, this is based upon the
* number of bits available in the registers
*/
#define XIIF_V123B_MAX_REG_BIT_COUNT 32
XStatus
XIpIfV123b_SelfTest(u32 RegBaseAddress, u8 IpRegistersWidth)
{
XStatus Status;
/* assert to verify arguments are valid */
XASSERT_NONVOID(IpRegistersWidth <= XIIF_V123B_MAX_REG_BIT_COUNT);
/* reset the IPIF such that it's in a known state before the test
* and interrupts are globally disabled
*/
XIIF_V123B_RESET(RegBaseAddress);
/* perform the self test on the IP interrupt registers, if
* it is not successful exit with the status
*/
Status = IpIntrSelfTest(RegBaseAddress, IpRegistersWidth);
if (Status != XST_SUCCESS) {
return Status;
}
/* reset the IPIF such that it's in a known state before exiting test */
XIIF_V123B_RESET(RegBaseAddress);
/* reaching this point means there were no errors, return success */
return XST_SUCCESS;
}
/******************************************************************************
*
* FUNCTION:
*
* IpIntrSelfTest
*
* DESCRIPTION:
*
* Perform a self test on the IP interrupt registers of the IPIF. This
* function modifies registers of the IPIF such that they are not guaranteed
* to be in the same state when it returns. Any bits in the IP interrupt
* status register which are set are assumed to be set by default after a reset
* and are not tested in the test.
*
* ARGUMENTS:
*
* InstancePtr points to the XIpIf to operate on.
*
* IpRegistersWidth contains the number of bits in the IP interrupt registers
* of the device. The hardware is parameterizable such that only the number of
* bits necessary to support a device are implemented. This value must be
* between 0 and 32 with 0 indicating there are no IP interrupt registers used.
*
* RETURN VALUE:
*
* A status indicating XST_SUCCESS if the test was successful. Otherwise, one
* of the following values is returned.
*
* XST_IPIF_RESET_REGISTER_ERROR The value of a register at reset was
* not valid
* XST_IPIF_IP_STATUS_ERROR A write to the IP interrupt status
* register did not read back correctly
* XST_IPIF_IP_ACK_ERROR One or more bits in the IP status
* register did not reset when acked
* XST_IPIF_IP_ENABLE_ERROR The IP interrupt enable register
* did not read back correctly based upon
* what was written to it
* NOTES:
*
* None.
*
******************************************************************************/
static XStatus
IpIntrSelfTest(u32 RegBaseAddress, u32 IpRegistersWidth)
{
/* ensure that the IP interrupt interrupt enable register is zero
* as it should be at reset, the interrupt status is dependent upon the
* IP such that it's reset value is not known
*/
if (XIIF_V123B_READ_IIER(RegBaseAddress) != 0) {
return XST_IPIF_RESET_REGISTER_ERROR;
}
/* if there are any used IP interrupts, then test all of the interrupt
* bits in all testable registers
*/
if (IpRegistersWidth > 0) {
u32 BitCount;
u32 IpInterruptMask = XIIF_V123B_FIRST_BIT_MASK;
u32 Mask = XIIF_V123B_FIRST_BIT_MASK; /* bits assigned MSB to LSB */
u32 InterruptStatus;
/* generate the register masks to be used for IP register tests, the
* number of bits supported by the hardware is parameterizable such
* that only that number of bits are implemented in the registers, the
* bits are allocated starting at the MSB of the registers
*/
for (BitCount = 1; BitCount < IpRegistersWidth; BitCount++) {
Mask = Mask << 1;
IpInterruptMask |= Mask;
}
/* get the current IP interrupt status register contents, any bits
* already set must default to 1 at reset in the device and these
* bits can't be tested in the following test, remove these bits from
* the mask that was generated for the test
*/
InterruptStatus = XIIF_V123B_READ_IISR(RegBaseAddress);
IpInterruptMask &= ~InterruptStatus;
/* set the bits in the device status register and verify them by reading
* the register again, all bits of the register are latched
*/
XIIF_V123B_WRITE_IISR(RegBaseAddress, IpInterruptMask);
InterruptStatus = XIIF_V123B_READ_IISR(RegBaseAddress);
if ((InterruptStatus & IpInterruptMask) != IpInterruptMask)
{
return XST_IPIF_IP_STATUS_ERROR;
}
/* test to ensure that the bits set in the IP interrupt status register
* can be cleared by acknowledging them in the IP interrupt status
* register then read it again and verify it was cleared
*/
XIIF_V123B_WRITE_IISR(RegBaseAddress, IpInterruptMask);
InterruptStatus = XIIF_V123B_READ_IISR(RegBaseAddress);
if ((InterruptStatus & IpInterruptMask) != 0) {
return XST_IPIF_IP_ACK_ERROR;
}
/* set the IP interrupt enable set register and then read the IP
* interrupt enable register and verify the interrupts were enabled
*/
XIIF_V123B_WRITE_IIER(RegBaseAddress, IpInterruptMask);
if (XIIF_V123B_READ_IIER(RegBaseAddress) != IpInterruptMask) {
return XST_IPIF_IP_ENABLE_ERROR;
}
/* clear the IP interrupt enable register and then read the
* IP interrupt enable register and verify the interrupts were disabled
*/
XIIF_V123B_WRITE_IIER(RegBaseAddress, 0);
if (XIIF_V123B_READ_IIER(RegBaseAddress) != 0) {
return XST_IPIF_IP_ENABLE_ERROR;
}
}
return XST_SUCCESS;
}